Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Optimization of Tensile-Shear Strength in the Dissimilar Joint of Zn-Coated Steel and Low Carbon Steel

Automotive Experiences · Vol. 3 No. 3 (2020) · hlm. 115–125

DOI
10.31603/ae.v3i3.4053
ISSN
2615-6636, 2615-6202
Terbit
2020-10-22
Penerbit
Universitas Muhammadiyah Magelang
Bahasa
en

Abstrak

The present study features analytical and experimental results of optimizing resistance spot welding performed using a pneumatic force system (PFS). The optimization was performed to join SECC-AF (JIS G 3313) galvanized steel material with SPCC-SD low carbon steel. The SECC-AF is an SPCC-SD (JIS G 3141) sheet plate coated with zinc (Zn) with a thickness of about 2.5 microns. The zinc coating on the metal surface causes its weldability to decrease. This study aims to obtain the highest tensile-shear strength test results from the combination of the specified resistance spot welding parameters. The research method used the Taguchi method using four variables and a combination of experimental levels. The experimental levels are 2-levels for the first parameter and 3-levels for other parameters. The Taguchi optimization experimental results achieved the highest tensile-shear strength at 5049.64 N. It properly worked at 22 squeeze time cycles, 25 kA of welding current, and 0.6-second welding time and 12 holding-time cycles. The S/N ratio analysis found that the welding current had the most significant effect, followed by welding time, squeeze time, and holding time. The delta S/N ratio values were 1.05, 0.67, 0.57 and 0.29, respectively.

Kata kunci

Jaringan kolaborasi para penulis

29 penulis · 113 tautan kepenulisan bersama · 55 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Sekolah Tinggi Teknologi Wastukancana
  • Universitas Buana Perjuangan Karawang
  • Universitas PGRI Semarang
  • Bandung Institute of Technology
  • Universiti Teknologi Brunei
  • University of Kuala Lumpur
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Khoirudin KhoirudinUniversitas Buana Perjuangan Karawang8
Apang Djafar ShieddiequeSekolah Tinggi Teknologi Wastukancana6
Nana RahdianaUniversitas Buana Perjuangan Karawang5
Sukarman SukarmanUniversitas Buana Perjuangan Karawang3
Amin RaisSekolah Tinggi Teknologi Wastukancana3
Aries AbbasUniversity of Kuala Lumpur3
Murtalim MurtalimUniversitas Buana Perjuangan Karawang3
Fathan Mubina DewadiUniversitas Buana Perjuangan Karawang3
Ismi KaniawulanSekolah Tinggi Teknologi Wastukancana1
M Rafi MuttaqinSekolah Tinggi Teknologi Wastukancana1
Dhiya UlhaqSekolah Tinggi Teknologi Wastukancana1
Ibnu Fatkhu RoyanaUniversitas PGRI Semarang1
Bertika KusumaUniversitas PGRI Semarang1
Mardiyati MardiyatiBandung Institute of Technology1
Bambang WidyantoBandung Institute of Technology1
Muhamad Taufik UlhakimUniversitas Buana Perjuangan Karawang1
Nazar FazrinUniversitas Buana Perjuangan Karawang1
Tomas IrfaniUniversitas Buana Perjuangan Karawang1
Afif HakimUniversitas Buana Perjuangan Karawang1
KhoirudinUniversitas Buana Perjuangan Karawang1
SukarmanUniversitas Buana Perjuangan Karawang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://journal.unimma.ac.id/index.php/AutomotiveExperiences/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 8 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Optimization of Tensile-Shear Strength in the Dissimilar Joint of Zn-Coated Steel and Low Carbon Steel</dc:title>
	<dc:creator xml:lang="en">Sukarman, Sukarman</dc:creator>
	<dc:creator xml:lang="en">Abdulah, Amri</dc:creator>
	<dc:creator xml:lang="en">Jatira, Jatira</dc:creator>
	<dc:creator xml:lang="en">Rajab, Dede Ardi</dc:creator>
	<dc:creator xml:lang="en">Rohman, Rohman</dc:creator>
	<dc:creator xml:lang="en">Anwar, Choirul</dc:creator>
	<dc:creator xml:lang="en">Aminanda, Yulfian</dc:creator>
	<dc:creator xml:lang="en">Akbar, Muhammad Ali</dc:creator>
	<dc:subject xml:lang="en">Resistance spot welding</dc:subject>
	<dc:subject xml:lang="en">Taguchi method</dc:subject>
	<dc:subject xml:lang="en">Galvanized steel</dc:subject>
	<dc:subject xml:lang="en">Shear-tensile strength</dc:subject>
	<dc:description xml:lang="en">The present study features analytical and experimental results of optimizing resistance spot welding performed using a pneumatic force system (PFS). The optimization was performed to join SECC-AF (JIS G 3313) galvanized steel material with SPCC-SD low carbon steel. The SECC-AF is an SPCC-SD (JIS G 3141) sheet plate coated with zinc (Zn) with a thickness of about 2.5 microns. The zinc coating on the metal surface causes its weldability to decrease. This study aims to obtain the highest tensile-shear strength test results from the combination of the specified resistance spot welding parameters. The research method used the Taguchi method using four variables and a combination of experimental levels. The experimental levels are 2-levels for the first parameter and 3-levels for other parameters. The Taguchi optimization experimental results achieved the highest tensile-shear strength at 5049.64 N. It properly worked at 22 squeeze time cycles, 25 kA of welding current, and 0.6-second welding time and 12 holding-time cycles. The S/N ratio analysis found that the welding current had the most significant effect, followed by welding time, squeeze time, and holding time. The delta S/N ratio values were 1.05, 0.67, 0.57 and 0.29, respectively.</dc:description>
	<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
	<dc:date>2020-10-22</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unimma.ac.id/AutomotiveExperiences/article/view/4053</dc:identifier>
	<dc:identifier>10.31603/ae.v3i3.4053</dc:identifier>
	<dc:source xml:lang="en">Automotive Experiences; Vol. 3 No. 3 (2020); 115-125</dc:source>
	<dc:source>2615-6636</dc:source>
	<dc:source>2615-6202</dc:source>
	<dc:source>10.31603/ae.v3i3</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unimma.ac.id/AutomotiveExperiences/article/view/4053/1937</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2020 Sukarman - Sukarman, Amri Abdulah, Jatira Jatira, Dede Ardi Rajab, Rohman Rohman, Choirul Anwar, Yulfian Aminanda, Muhammad Ali Akbar</dc:rights>
</oai_dc:dc>