Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Effect of Electrode Diameter and Current on Dissimilar Metal Welding (Stainless Steel - Galvanized Steel) in Bus Body Construction: Microstructure and Properties Evaluation

Automotive Experiences · Vol. 5 No. 3 (2022) · hlm. 402–415

DOI
10.31603/ae.7094
ISSN
2615-6636, 2615-6202
Terbit
2022-07-23
Penerbit
Universitas Muhammadiyah Magelang
Bahasa
en

Abstrak

This study evaluates the macrostructure, microstructure, hardness, and tensile strength in dissimilar metal welding applied to bus body construction. The process involved joining hollow stainless steel and galvanized steel at the dimensions of 80 x 40 x 3.2 mm through Gas Metal Arc Welding (GMAW). The current was varied at 90, 100, and 110 A while ER70S-6 electrodes with diameters of 0.8 and 1.0 mm were used. The results showed that electrode diameter and welding current affect the capping area, penetration depth, and hardness. Moreover, the formation of the widmasatten ferrite phase was increased and the coarse grain boundaries in the weld zone were detected. It was also observed that an increase in the diameter of the electrode and the welding current which indicates an increment in the heat reduced the rate of solidification and cooling. The average tensile strength for all the samples investigated was found to be lower than the value for the base metal. Therefore, further research is recommended to improve the tensile strength.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 86 tautan kepenulisan bersama · 22 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • State University of Semarang
  • National Nuclear Energy Agency of Indonesia
  • Sekolah Tinggi Ilmu Kesehatan Harapan Ibu Jambi
  • Universitas Wahid Hasyim
  • Universitas Jambi
  • Pertamina (Indonesia)
  • Bandung Institute of Technology
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
S. SugihartoNational Nuclear Energy Agency of Indonesia2
Supadi SupadiAfiliasi tidak diketahui1
Tatas Aldian SukmanaState University of Semarang1
Vita Soniya MaslivahState University of Semarang1
Emi PujiastutiState University of Semarang1
Karina PratinuariState University of Semarang1
Alamsyah AlamsyahState University of Semarang1
Atik SuryaniState University of Semarang1
Hery SutartoState University of Semarang1
Yan Amal AbdilahState University of Semarang1
Adi Nur CahyonoState University of Semarang1
Arinto Surya PriambodoState University of Semarang1
Edy SoedjokoState University of Semarang1
Anisa Nur AfridaState University of Semarang1
Isnarto IsnartoState University of Semarang1
Erna KuneniState University of Semarang1
Sumarni SumarniUniversitas Jambi1
Sunarmi SunarmiState University of Semarang1
Rochmad RochmadState University of Semarang1
Mita KonitaState University of Semarang1
Zaenuri ZaenuriState University of Semarang1
Hilyatin FardaState University of Semarang1
Muh. Fajar Safa’atullahState University of Semarang1
Kurnia Setyo RiniState University of Semarang1
Ririn RosnardiSekolah Tinggi Ilmu Kesehatan Harapan Ibu Jambi1
Aidil HafizSekolah Tinggi Ilmu Kesehatan Harapan Ibu Jambi1
Putri Sahara HarahapSekolah Tinggi Ilmu Kesehatan Harapan Ibu Jambi1
Fhala Sasqia AsharSekolah Tinggi Ilmu Kesehatan Harapan Ibu Jambi1
Achdiyat AchdiyatNational Nuclear Energy Agency of Indonesia1
B. AzmiNational Nuclear Energy Agency of Indonesia1
A. YaniPertamina (Indonesia)1
Wibisono WibisonoNational Nuclear Energy Agency of Indonesia1
Kushartono KushartonoNational Nuclear Energy Agency of Indonesia1
T. SuryantoroNational Nuclear Energy Agency of Indonesia1
Rizal KurniadiBandung Institute of Technology1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://journal.unimma.ac.id/index.php/AutomotiveExperiences/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Effect of Electrode Diameter and Current on Dissimilar Metal Welding (Stainless Steel - Galvanized Steel) in Bus Body Construction: Microstructure and Properties Evaluation</dc:title>
	<dc:creator xml:lang="en">Suntari, Suntari</dc:creator>
	<dc:creator xml:lang="en">Purwanto, Helmy</dc:creator>
	<dc:creator xml:lang="en">Respati, Sri Mulyo Bondan</dc:creator>
	<dc:creator xml:lang="en">Sugiarto, Sugiarto</dc:creator>
	<dc:creator xml:lang="en">Abidin, Zainal</dc:creator>
	<dc:subject xml:lang="en">Dissimilar welding</dc:subject>
	<dc:subject xml:lang="en">Material properties</dc:subject>
	<dc:subject xml:lang="en">Body bus construction</dc:subject>
	<dc:description xml:lang="en">This study evaluates the macrostructure, microstructure, hardness, and tensile strength in dissimilar metal welding applied to bus body construction. The process involved joining hollow stainless steel and galvanized steel at the dimensions of 80 x 40 x 3.2 mm through Gas Metal Arc Welding (GMAW). The current was varied at 90, 100, and 110 A while ER70S-6 electrodes with diameters of 0.8 and 1.0 mm were used. The results showed that electrode diameter and welding current affect the capping area, penetration depth, and hardness. Moreover, the formation of the widmasatten ferrite phase was increased and the coarse grain boundaries in the weld zone were detected. It was also observed that an increase in the diameter of the electrode and the welding current which indicates an increment in the heat reduced the rate of solidification and cooling. The average tensile strength for all the samples investigated was found to be lower than the value for the base metal. Therefore, further research is recommended to improve the tensile strength.</dc:description>
	<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
	<dc:date>2022-07-23</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unimma.ac.id/AutomotiveExperiences/article/view/7094</dc:identifier>
	<dc:identifier>10.31603/ae.7094</dc:identifier>
	<dc:source xml:lang="en">Automotive Experiences; Vol. 5 No. 3 (2022); 402-415</dc:source>
	<dc:source>2615-6636</dc:source>
	<dc:source>2615-6202</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unimma.ac.id/AutomotiveExperiences/article/view/7094/3482</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2022 Suntari Suntari, Helmy Purwanto, Sri Mulyo Bondan Respati, Sugiarto Sugiarto, Zainal Abidin</dc:rights>
</oai_dc:dc>