Jurnal
SINTA 1
Evaluation of Bogie Bolster Centre Plate and Side Bearing under Vertical Static Loads through Finite Element (FEA) Modelling
INDONESIAN JOURNAL OF APPLIED PHYSICS · Vol. 15 No. 2 (2025) · hlm. 449–463
ISSN 2477-6416, 2089-0133
Terbit 2025-10-30
Penerbit Department of Physics, Sebelas Maret University
Bahasa eng
Abstrak
The bolster is one of the main structural elements in railway bogies, playing the central role of transmitting vertical and dynamic loads from the train body to the wheel-sets. The mechanical behavior of an ASTM A148 Grade 80-50 material bolster under vertical static loading is examined in this work. This simulation is analyzed by applying the Finite Element Analysis (FEA) using student version software with nonlinear static analysis, which was run with a tetrahedral mesh and Newton-Raphson iteration. There are three variables, respectively, two variables as dependent, such as Von Misses Stress (VMS) and total deformation resulting from the loading condition. Then, the independent variable is a loading value based on the AAR M-202 standard. In this work, three values of loading condition were carried out, such as P1 = 536010.7 N, P2 = 854058.8 N, P3 = 1027500 N respectively. The result of the simulation shows that the maximum average stress in the critical area is 305.58 MPa, which is still less than the yield strength of the material at 390 MPa. The maximum elastic deflection of 0.102 mm is well within the AAR M-202 standard allowable values. In conclusion, bolster bogie based on ASTM A148 Grade 80-50 has reliability for static loading and is available with a safety factor according to the AAR M-202 standard.
Jaringan kolaborasi para penulis
12 penulis ·
22 tautan kepenulisan bersama
· 3 lintas organisasi
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
Udayana University Politeknik Negeri Bali Afiliasi tidak diketahui
Organisasi berbeda
Organisasi sama
Afiliasi tidak diketahui
Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.
Sumber metadata: OAI-PMH (metadata jurnal) https://jurnal.uns.ac.id/ijap/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/ http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
<dc:title xml:lang="en-US">Evaluation of Bogie Bolster Centre Plate and Side Bearing under Vertical Static Loads through Finite Element (FEA) Modelling</dc:title>
<dc:creator>Artha Wirawan, I.P.</dc:creator>
<dc:creator>Ary Subagia, I.D.G</dc:creator>
<dc:creator>Adiatmika, I.K</dc:creator>
<dc:creator>Farid, A.R</dc:creator>
<dc:subject xml:lang="en-US">Bogie Bolster; Deflection, Finite Element Method; Static Loading; Train; Stress Strain</dc:subject>
<dc:description xml:lang="en-US">The bolster is one of the main structural elements in railway bogies, playing the central role of transmitting vertical and dynamic loads from the train body to the wheel-sets. The mechanical behavior of an ASTM A148 Grade 80-50 material bolster under vertical static loading is examined in this work. This simulation is analyzed by applying the Finite Element Analysis (FEA) using student version software with nonlinear static analysis, which was run with a tetrahedral mesh and Newton-Raphson iteration. There are three variables, respectively, two variables as dependent, such as Von Misses Stress (VMS) and total deformation resulting from the loading condition. Then, the independent variable is a loading value based on the AAR M-202 standard. In this work, three values of loading condition were carried out, such as P1 = 536010.7 N, P2 = 854058.8 N, P3 = 1027500 N respectively. The result of the simulation shows that the maximum average stress in the critical area is 305.58 MPa, which is still less than the yield strength of the material at 390 MPa. The maximum elastic deflection of 0.102 mm is well within the AAR M-202 standard allowable values. In conclusion, bolster bogie based on ASTM A148 Grade 80-50 has reliability for static loading and is available with a safety factor according to the AAR M-202 standard.</dc:description>
<dc:publisher xml:lang="en-US">Department of Physics, Sebelas Maret University</dc:publisher>
<dc:contributor xml:lang="en-US"></dc:contributor>
<dc:date>2025-10-30</dc:date>
<dc:type>info:eu-repo/semantics/article</dc:type>
<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
<dc:format>application/pdf</dc:format>
<dc:identifier>https://jurnal.uns.ac.id/ijap/article/view/105272</dc:identifier>
<dc:identifier>10.13057/ijap.v15i2.105272</dc:identifier>
<dc:source xml:lang="en-US">INDONESIAN JOURNAL OF APPLIED PHYSICS; Vol 15, No 2 (2025): October; 449-463</dc:source>
<dc:source>2477-6416</dc:source>
<dc:source>2089-0133</dc:source>
<dc:language>eng</dc:language>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/view/105272/52269</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22284</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22285</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22286</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22287</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22288</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22289</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22290</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22291</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/105272/22292</dc:relation>
<dc:rights xml:lang="en-US">Copyright (c) 2025 INDONESIAN JOURNAL OF APPLIED PHYSICS</dc:rights>
</oai_dc:dc>
Sitasi dan pengindeksan
Jumlah menurut tiap indeks pada 13 Nov 2026; setiap indeks menghitung sitasi dengan cara berbeda.
OpenAlex juga mencatat karya ini di: crossref, doaj.
Sitasi artikel ini
APA 7
Artha Wirawan, I., Ary Subagia, I., Adiatmika, I., & Farid, A. (2025). Evaluation of Bogie Bolster Centre Plate and Side Bearing under Vertical Static Loads through Finite Element (FEA) Modelling. INDONESIAN JOURNAL OF APPLIED PHYSICS, 15(2), 449–463. https://doi.org/10.13057/ijap.v15i2.105272
Salin
IEEE
I. Artha Wirawan, I. Ary Subagia, I. Adiatmika, and A. Farid, “Evaluation of Bogie Bolster Centre Plate and Side Bearing under Vertical Static Loads through Finite Element (FEA) Modelling,” INDONESIAN JOURNAL OF APPLIED PHYSICS, vol. 15, no. 2, pp. 449–463, 2025, doi: 10.13057/ijap.v15i2.105272.
Salin
Dibuat dari metadata jurnal; periksa nama penulis sebelum dipakai.