Jurnal
SINTA 1
Thermo-Fluid Dynamics of PLA Deposition in Fused Filament Fabrication 3D Printing: A Numerical Study
INDONESIAN JOURNAL OF APPLIED PHYSICS · Vol. 15 No. 1 (2025) · hlm. 110–123
ISSN 2477-6416, 2089-0133
Terbit 2025-05-04
Penerbit Department of Physics, Sebelas Maret University
Bahasa eng
Abstrak
Prototyping plays an important role in product design and has recently gained benefit from the rising popularity of 3D printing. It is to be expected that 3D printing will accommodate more materials, which need to be tailored to specific design requirements. Insights into heat transfer and fluid flows (thermo-fluid dynamics) in the printing process is thus essential to obtain favorable process parameters that can lead to high quality prints. In this work, polylactic acid (PLA) melt in Fused Filament Fabrication (FFF) 3D printing was numerically studied through Computational Fluid Dynamics (CFD) simulations, with a focus on the thermo-fluid dynamics of the strand deposition of the filament melt on the printer platform. The study was carried out by evaluating 6 printing cases, with a variation of 2 key process parameters, i.e., printing speed (30 and 45 mm/s) and platform temperature (310, 320, and 340 K). The simulation results showed that the free surface in the tip region of the strand has the most tendency to adhere to the printing platform heated at 340 K with the printing speed of 45 mm/s, as compared with other cases. This was affected by the lower dynamic viscosity in the region, relative to other cases, resulting from the high platform temperature and shear rate generated by the high printing speed.
Jaringan kolaborasi para penulis
18 penulis ·
38 tautan kepenulisan bersama
· 7 lintas organisasi
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
Universitas Pembangunan Jaya Muria Kudus University Satya Wacana Christian University Monash University Afiliasi tidak diketahui
Organisasi berbeda
Organisasi sama
Afiliasi tidak diketahui
Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.
Sumber metadata: OAI-PMH (metadata jurnal) https://jurnal.uns.ac.id/ijap/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 8 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/ http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
<dc:title xml:lang="en-US">Thermo-Fluid Dynamics of PLA Deposition in Fused Filament Fabrication 3D Printing: A Numerical Study</dc:title>
<dc:creator>Saldi, Zaki Saptari</dc:creator>
<dc:creator>Purnama, Purba</dc:creator>
<dc:creator>Nurmalia, Nurmalia</dc:creator>
<dc:creator>Alfarisi, Salman</dc:creator>
<dc:creator>Arifin, Muhammad</dc:creator>
<dc:creator>Suweco, Ammar Munadi</dc:creator>
<dc:subject xml:lang="en-US">3D printing; Computational Fluid Dynamics; Fused Filament Fabrication; thermo-fluid dynamics; polylactic acid</dc:subject>
<dc:description xml:lang="en-US">Prototyping plays an important role in product design and has recently gained benefit from the rising popularity of 3D printing. It is to be expected that 3D printing will accommodate more materials, which need to be tailored to specific design requirements. Insights into heat transfer and fluid flows (thermo-fluid dynamics) in the printing process is thus essential to obtain favorable process parameters that can lead to high quality prints. In this work, polylactic acid (PLA) melt in Fused Filament Fabrication (FFF) 3D printing was numerically studied through Computational Fluid Dynamics (CFD) simulations, with a focus on the thermo-fluid dynamics of the strand deposition of the filament melt on the printer platform. The study was carried out by evaluating 6 printing cases, with a variation of 2 key process parameters, i.e., printing speed (30 and 45 mm/s) and platform temperature (310, 320, and 340 K). The simulation results showed that the free surface in the tip region of the strand has the most tendency to adhere to the printing platform heated at 340 K with the printing speed of 45 mm/s, as compared with other cases. This was affected by the lower dynamic viscosity in the region, relative to other cases, resulting from the high platform temperature and shear rate generated by the high printing speed.</dc:description>
<dc:publisher xml:lang="en-US">Department of Physics, Sebelas Maret University</dc:publisher>
<dc:contributor xml:lang="en-US">The Ministry of Education, Culture, Research and Technology (Kemendikbudristek)</dc:contributor>
<dc:contributor xml:lang="en-US">Universitas Prasetiya Mulya</dc:contributor>
<dc:date>2025-05-04</dc:date>
<dc:type>info:eu-repo/semantics/article</dc:type>
<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
<dc:format>application/pdf</dc:format>
<dc:identifier>https://jurnal.uns.ac.id/ijap/article/view/87634</dc:identifier>
<dc:identifier>10.13057/ijap.v15i1.87634</dc:identifier>
<dc:source xml:lang="en-US">INDONESIAN JOURNAL OF APPLIED PHYSICS; Vol 15, No 1 (2025): April; 110-123</dc:source>
<dc:source>2477-6416</dc:source>
<dc:source>2089-0133</dc:source>
<dc:language>eng</dc:language>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/view/87634/50046</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/87634/17401</dc:relation>
<dc:relation>https://jurnal.uns.ac.id/ijap/article/downloadSuppFile/87634/17402</dc:relation>
<dc:rights xml:lang="en-US">Copyright (c) 2025 INDONESIAN JOURNAL OF APPLIED PHYSICS</dc:rights>
</oai_dc:dc>
Sitasi dan pengindeksan
Jumlah menurut tiap indeks pada 13 Nov 2026; setiap indeks menghitung sitasi dengan cara berbeda.
OpenAlex juga mencatat karya ini di: crossref, doaj.
Sitasi artikel ini
APA 7
Saldi, Z. S., Purnama, P., Nurmalia, N., Alfarisi, S., Arifin, M., & Suweco, A. M. (2025). Thermo-Fluid Dynamics of PLA Deposition in Fused Filament Fabrication 3D Printing: A Numerical Study. INDONESIAN JOURNAL OF APPLIED PHYSICS, 15(1), 110–123. https://doi.org/10.13057/ijap.v15i1.87634
Salin
IEEE
Z. S. Saldi, P. Purnama, N. Nurmalia, S. Alfarisi, M. Arifin, and A. M. Suweco, “Thermo-Fluid Dynamics of PLA Deposition in Fused Filament Fabrication 3D Printing: A Numerical Study,” INDONESIAN JOURNAL OF APPLIED PHYSICS, vol. 15, no. 1, pp. 110–123, 2025, doi: 10.13057/ijap.v15i1.87634.
Salin
Dibuat dari metadata jurnal; periksa nama penulis sebelum dipakai.