Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Development of a hydraulic jack system bending tool for improved manufacturing efficiency

International Journal of Advances in Applied Sciences · Vol. 14 No. 4 (2025) · hlm. 1072–1082

DOI
10.11591/ijaas.v14.i4.pp1072-1082
ISSN
2722-2594, 2252-8814
Terbit
2025-12-01
Penerbit
Institute of Advanced Engineering and Science
Bahasa
eng
Lisensi
creativecommons.org/licenses/by-sa/4.0

Abstrak

This article presents the design, fabrication, and testing of a hydraulic sheet metal bending tool. The main objective was to create a tool capable of bending sheets of various thicknesses, ranging from 2 to 4 mm, with high precision and minimal operator effort. The design incorporates a hydraulic ram for easy operation, allowing multiple plates to be bent in a short period of time. Key calculations, including bending force, spring load, and hydraulic force, are performed to ensure the efficiency and safety of the tool. Experimental results show that the tool is able to achieve the desired bending angles, with minimal spring return, and can handle up to three 10 cm wide sheets in approximately 10 minutes. The performance of the tool has been proven by tests, and the results confirm that it can meet the requirements of industrial sheet metal bending. Based on these results, the tool demonstrates its effectiveness in small and medium-scale operations, providing a cost-effective solution for sheet metal production.

Jaringan kolaborasi para penulis

18 penulis · 50 tautan kepenulisan bersama · 12 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Ujung Pandang
  • University of Technology Malaysia
  • Politeknik Bosowa
  • State University of Makassar
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Muhammad IswarPoliteknik Negeri Ujung Pandang3
Muhira Dzar FarabyPoliteknik Negeri Ujung Pandang2
Syahrisal SyahrisalAfiliasi tidak diketahui2
Mohd Wazir MustafaUniversity of Technology Malaysia1
Makmur SainiPoliteknik Negeri Ujung Pandang1
Abdullah Asuhaimi Mohd ZinUniversity of Technology Malaysia1
A. R. SultanPoliteknik Negeri Ujung Pandang1
Asrul HidayatPoliteknik Bosowa1
Arthur Halik RazakPoliteknik Negeri Ujung Pandang1
Yosrihard BasonganPoliteknik Negeri Ujung Pandang1
Mahadir SirmanAfiliasi tidak diketahui1
Henny Pasandang NariAfiliasi tidak diketahui1
Mukhlisin MukhlisinState University of Makassar1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://ijaas.iaescore.com/index.php/IJAAS/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 8 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Development of a hydraulic jack system bending tool for improved manufacturing efficiency</dc:title>
	<dc:creator>Suyuti, Muhammad Arsyad</dc:creator>
	<dc:creator>Nur, Rusdi</dc:creator>
	<dc:creator>Muttaqin, Ahmad Nurul</dc:creator>
	<dc:creator>Arminas, Arminas</dc:creator>
	<dc:creator>Sudirman, Zainal</dc:creator>
	<dc:description xml:lang="en-US">This article presents the design, fabrication, and testing of a hydraulic sheet metal bending tool. The main objective was to create a tool capable of bending sheets of various thicknesses, ranging from 2 to 4 mm, with high precision and minimal operator effort. The design incorporates a hydraulic ram for easy operation, allowing multiple plates to be bent in a short period of time. Key calculations, including bending force, spring load, and hydraulic force, are performed to ensure the efficiency and safety of the tool. Experimental results show that the tool is able to achieve the desired bending angles, with minimal spring return, and can handle up to three 10 cm wide sheets in approximately 10 minutes. The performance of the tool has been proven by tests, and the results confirm that it can meet the requirements of industrial sheet metal bending. Based on these results, the tool demonstrates its effectiveness in small and medium-scale operations, providing a cost-effective solution for sheet metal production.</dc:description>
	<dc:publisher xml:lang="en-US">Institute of Advanced Engineering and Science</dc:publisher>
	<dc:contributor xml:lang="en-US"></dc:contributor>
	<dc:date>2025-12-01</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US"></dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ijaas.iaescore.com/index.php/IJAAS/article/view/21779</dc:identifier>
	<dc:identifier>10.11591/ijaas.v14.i4.pp1072-1082</dc:identifier>
	<dc:source xml:lang="en-US">International Journal of Advances in Applied Sciences; Vol 14, No 4: December 2025; 1072-1082</dc:source>
	<dc:source>2722-2594</dc:source>
	<dc:source>2252-8814</dc:source>
	<dc:source>10.11591/ijaas.v14.i4</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ijaas.iaescore.com/index.php/IJAAS/article/view/21779/13345</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025 Muhammad Arsyad Suyuti, Rusdi Nur, Ahmad Nurul Muttaqin, Arminas Arminas, Zainal Sudirman</dc:rights>
	<dc:rights xml:lang="en-US">http://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>