Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Energy saving of variable frequency drive in dust collector fan motors in the smelting process at the steel industry

International Journal of Power Electronics and Drive Systems · Vol. 16 No. 2 (2025) · hlm. 1399–1408

DOI
10.11591/ijpeds.v16.i2.pp1399-1408
ISSN
2722-256X, 2088-8694
Terbit
2025-06-01
Penerbit
Institute of Advanced Engineering and Science
Bahasa
eng
Lisensi
creativecommons.org/licenses/by-sa/4.0

Abstrak

The dust removal system is a crucial component in the steel industry, designed to eliminate dust and gas generated during the smelting process. Its primary purpose is to prevent personnel in the surrounding area from inhaling harmful dust particles. A dust collector system is used to carry out this process before being removed from the chimney to the outside air. In the operation of the dust collector, there is still limited attention given to optimizing its operation to meet the needs of its load, where the dust collector still operates at maximum capacity continuously when the dust load decreases due to the smelting process, in an idle state. Setting the rotational speed of the fan motor to produce an airflow rate as required using a variable frequency drive (VFD). The Motor speed was varied in low and high conditions at 322 rpm and 879 rpm. The research results showed that the average airflow rate for the speed of 322 rpm was 150,326 m³/h, and it has 384.193 m³/h at the speed of 879 rpm. The energy savings obtained from the application of VFD to control the airflow rate value are 1,253,544 kWh/year, and the cost savings obtained are IDR 1,249,457,447 per year.

Kata kunci

Jaringan kolaborasi para penulis

30 penulis · 78 tautan kepenulisan bersama · 39 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Diponegoro University
  • Universitas Ahmad Dahlan
  • Sultan Agung Islamic University
  • SRM Institute of Science and Technology
  • State University of Semarang
  • National Research and Innovation Agency
  • Universiti Tenaga Nasional
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Tole SutiknoUniversitas Ahmad Dahlan6
Watra ArsadiandoAfiliasi tidak diketahui2
Hendril Satrian PurnamaAfiliasi tidak diketahui2
Wahyu Sapto AjiUniversitas Ahmad Dahlan2
Teguh Budi PrakosoDiponegoro University1
Fredi PrastiyoDiponegoro University1
Susatyo HandokoDiponegoro University1
Muhammad ZainuriDiponegoro University1
Sudjadi SudjadiDiponegoro University1
Emak Pancar SaktiDiponegoro University1
Auzani JidinUniversiti Teknikal Malaysia Melaka1
Preethicaa RameshSRM Institute of Science and Technology1
Sowmmiya USRM Institute of Science and Technology1
Vigna K. RamachandaramurthyUniversiti Tenaga Nasional1
Chee Wei TanUniversity of Technology Malaysia1
Tri WahonoUniversitas Ahmad Dahlan1
Lina HandayaniUniversitas Ahmad Dahlan1
Zainal SalamAfiliasi tidak diketahui1
Munawar Agus RiyadiDiponegoro University1
Imam Much Ibnu SubrotoSultan Agung Islamic University1
Arief MarwantoSultan Agung Islamic University1
Gunawan GunawanSultan Agung Islamic University1
Hermawan HermawanDiponegoro University1
Riza Arif PratamaUniversitas Tunas Pembangunan1
Nur IksanState University of Semarang1
Abdul SyakurDiponegoro University1
Anindira Listy HartisaState University of Semarang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://ijpeds.iaescore.com/index.php/IJPEDS/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Energy saving of variable frequency drive in dust collector fan motors in the smelting process at the steel industry</dc:title>
	<dc:creator>Turinno, Sarwo</dc:creator>
	<dc:creator>Facta, Mochammad</dc:creator>
	<dc:creator>Cahyadi, Cahyadi</dc:creator>
	<dc:subject xml:lang="en-US">dust collector system; energy saving; motor fan; steel industry; variable frequency drive</dc:subject>
	<dc:description xml:lang="en-US">The dust removal system is a crucial component in the steel industry, designed to eliminate dust and gas generated during the smelting process. Its primary purpose is to prevent personnel in the surrounding area from inhaling harmful dust particles. A dust collector system is used to carry out this process before being removed from the chimney to the outside air. In the operation of the dust collector, there is still limited attention given to optimizing its operation to meet the needs of its load, where the dust collector still operates at maximum capacity continuously when the dust load decreases due to the smelting process, in an idle state. Setting the rotational speed of the fan motor to produce an airflow rate as required using a variable frequency drive (VFD). The Motor speed was varied in low and high conditions at 322 rpm and 879 rpm. The research results showed that the average airflow rate for the speed of 322 rpm was 150,326 m³/h, and it has 384.193 m³/h at the speed of 879 rpm. The energy savings obtained from the application of VFD to control the airflow rate value are 1,253,544 kWh/year, and the cost savings obtained are IDR 1,249,457,447 per year.</dc:description>
	<dc:publisher xml:lang="en-US">Institute of Advanced Engineering and Science</dc:publisher>
	<dc:contributor xml:lang="en-US"></dc:contributor>
	<dc:date>2025-06-01</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US"></dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ijpeds.iaescore.com/index.php/IJPEDS/article/view/23532</dc:identifier>
	<dc:identifier>10.11591/ijpeds.v16.i2.pp1399-1408</dc:identifier>
	<dc:source xml:lang="en-US">International Journal of Power Electronics and Drive Systems (IJPEDS); Vol 16, No 2: June 2025; 1399-1408</dc:source>
	<dc:source>2722-256X</dc:source>
	<dc:source>2088-8694</dc:source>
	<dc:source>10.11591/ijpeds.v16.i2</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ijpeds.iaescore.com/index.php/IJPEDS/article/view/23532/14976</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025 Sarwo Turinno, Mochammad Facta, Cahyadi Cahyadi</dc:rights>
	<dc:rights xml:lang="en-US">http://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>