Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

DC-DC Boost Converter Design for Fast and Accurate MPPT Algorithms in Stand-Alone Photovoltaic System

International Journal of Power Electronics and Drive Systems · Vol. 9 No. 3 (2018) · hlm. 1038–1050

DOI
10.11591/ijpeds.v9.i3.pp1038-1050
ISSN
2722-256X, 2088-8694
Terbit
2018-09-01
Penerbit
Institute of Advanced Engineering and Science
Bahasa
eng
Lisensi
creativecommons.org/licenses/by-sa/4.0

Abstrak

The main components of a Stand-Alone Photovoltaic (SAPV) system consists of PV array, DC-DC converter, load and the maximum power point tracking (MPPT) control algorithm. MPPT algorithm was used for extracting maximum available power from PV module under a particular environmental condition by controlling the duty ratio of DC-DC converter. Based on maximum power transfer theorem, by changing the duty cycle, the load resistance as seen by the source is varied and matched with the internal resistance of PV module at maximum power point (MPP) so as to transfer the maximum power. Under sudden changes in solar irradiance, the selection of MPPT algorithm’s sampling time (TS_MPPT) is very much depends on two main components of the converter circuit namely; inductor and capacitor. As the value of these components increases, the settling time of the transient response for PV voltage and current will also increase linearly. Consequently, TS_MPPT needs to be increased for accurate MPPT and therefore reduce the tracking speed. This work presents a design considerations of DC-DC Boost Converter used in SAPV system for fast and accurate MPPT algorithm. The conventional Hill Climbing (HC) algorithm has been applied to track the MPP when subjected to sudden changes in solar irradiance. By selecting the optimum value of the converter circuit components, a fast and accurate MPPT especially during sudden changes in irradiance has been realized.

Jaringan kolaborasi para penulis

22 penulis · 57 tautan kepenulisan bersama · 15 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universiti Teknologi MARA
  • University of Technology Malaysia
  • Universiti Teknikal Malaysia Melaka
  • Swinburne University of Technology
  • Islamia University of Bahawalpur
  • Government College University, Faisalabad
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Rahimi BaharomUniversiti Teknologi MARA4
Ismail MusirinUniversiti Teknologi MARA3
Azhan Ab RahmanUniversiti Teknikal Malaysia Melaka3
Muhammad Murtadha OthmanUniversiti Teknologi MARA2
Muhammad Khairul Azman Mohd JamhariUniversiti Teknologi MARA2
Naeem M. S. HannoonUniversiti Teknologi MARA1
Nor Farahaida Abdul RahmanUniversiti Teknologi MARA1
Ahmad Farid AbidinUniversiti Teknologi MARA1
Khairul Safuan MuhammadUniversiti Teknologi MARA1
Dygku Aniqnatasa Awg OsmanUniversiti Teknologi MARA1
Muhamad Nabil Bin HidayatUniversiti Teknologi MARA1
Jubaer AhmedSwinburne University of Technology1
Zulkifli RamliUniversity of Technology Malaysia1
Muhammad AmjadIslamia University of Bahawalpur1
Mohd Junaidi Abdul AzizUniversity of Technology Malaysia1
Abdul Rauf BhattiGovernment College University, Faisalabad1
Kong Pui YeeUniversity of Technology Malaysia1
Muhammad Qusyairi Iqbal Mohd ZamaniUniversiti Teknologi MARA1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://ijpeds.iaescore.com/index.php/IJPEDS/oai, pertama di-harvest 8 Nov 2026, terakhir terlihat 8 Nov 2026.
Metadata asli (oai_dc) 
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">DC-DC Boost Converter Design for Fast and Accurate MPPT Algorithms in Stand-Alone Photovoltaic System</dc:title>
	<dc:creator>Hashim, Norazlan</dc:creator>
	<dc:creator>Salam, Zainal</dc:creator>
	<dc:creator>Johari, Dalina</dc:creator>
	<dc:creator>Nik Ismail, Nik Fasdi</dc:creator>
	<dc:description xml:lang="en-US">The main components of a Stand-Alone Photovoltaic (SAPV) system consists of PV array, DC-DC converter, load and the maximum power point tracking (MPPT) control algorithm. MPPT algorithm was used for extracting maximum available power from PV module under a particular environmental condition by controlling the duty ratio of DC-DC converter. Based on maximum power transfer theorem, by changing the duty cycle, the load resistance as seen by the source is varied and matched with the internal resistance of PV module at maximum power point (MPP) so as to transfer the maximum power. Under sudden changes in solar irradiance, the selection of MPPT algorithm’s sampling time (TS_MPPT) is very much depends on two main components of the converter circuit namely; inductor and capacitor. As the value of these components increases, the settling time of the transient response for PV voltage and current will also increase linearly. Consequently, TS_MPPT needs to be increased for accurate MPPT and therefore reduce the tracking speed. This work presents a design considerations of DC-DC Boost Converter used in SAPV system for fast and accurate MPPT algorithm. The conventional Hill Climbing (HC) algorithm has been applied to track the MPP when subjected to sudden changes in solar irradiance. By selecting the optimum value of the converter circuit components, a fast and accurate MPPT especially during sudden changes in irradiance has been realized.</dc:description>
	<dc:publisher xml:lang="en-US">Institute of Advanced Engineering and Science</dc:publisher>
	<dc:contributor xml:lang="en-US"></dc:contributor>
	<dc:date>2018-09-01</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US"></dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ijpeds.iaescore.com/index.php/IJPEDS/article/view/14399</dc:identifier>
	<dc:identifier>10.11591/ijpeds.v9.i3.pp1038-1050</dc:identifier>
	<dc:source xml:lang="en-US">International Journal of Power Electronics and Drive Systems (IJPEDS); Vol 9, No 3: September 2018; 1038-1050</dc:source>
	<dc:source>2722-256X</dc:source>
	<dc:source>2088-8694</dc:source>
	<dc:source>10.11591/ijpeds.v9.i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ijpeds.iaescore.com/index.php/IJPEDS/article/view/14399/11300</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2018 Norazlan Hashim, Zainal Salam, Dalina Johari, Nik Fasdi Nik Ismail</dc:rights>
	<dc:rights xml:lang="en-US">http://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>