Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Effect of Moisture Content of Green Sand on The Casting Defects

Journal of Applied Engineering and Technological Science (JAETS) · Vol. 2 No. 1 (2020) · hlm. 1–6

DOI
10.37385/jaets.v2i1.77
ISSN
2715-6079, 2715-6087
Terbit
2020-08-06
Penerbit
Yayasan Riset dan Pengembangan Intelektual (YRPI)
Bahasa
en

Abstrak

In this study, three percentages of moisture content on the green sand were benchmarked to be observed their effects on the casting defects. The metal used is scrap Al-Si with wt% of Al 59.7. The metal was melted in a furnace at 550 ºC then poured into sand molds and cooled for 24 hours before it can be removed, cleaned, and finished. There were prepared three specimens for each benchmark. Qualitative observation of defects was done by physical observations on the surface of the specimens. The observations show that on the moisture content of 2.5%, there is a defect in the form of porosity. Defects in the form of drops, misruns, blowholes, and shrinkage cavity are found on the benchmark 3.5%. The most severe defects are found on the benchmark 4.5% in the form of buckles and severe shrinkage cavities that are found in almost all specimens.

Kata kunci

Jaringan kolaborasi para penulis

27 penulis · 90 tautan kepenulisan bersama · 32 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Politeknik Negeri Semarang
  • Universitas Negeri Padang
  • State University of Malang
  • Politeknik Negeri Banyuwangi
  • Politeknik Negeri Samarinda
  • Cranfield University
  • Organisasi lain
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Andre KurniawanUniversitas Negeri Padang4
Lutfi HakimPoliteknik Negeri Banyuwangi4
Fataa KusumattaqiinPoliteknik Negeri Samarinda4
Rangga E. SantosoCranfield University4
Moh. HartonoPoliteknik Negeri Malang3
Moh. Nasir HariyantoPoliteknik Negeri Malang3
Syamsul HadiUniversity of Sarjanawiyata Tamansiswa3
Yusuf Dewantoro HerlambangPoliteknik Negeri Semarang1
Nanang ApriandiPoliteknik Negeri Semarang1
Avicenna An-NizhamiPoliteknik Negeri Semarang1
Bono BonoPoliteknik Negeri Semarang1
Friska Ayu Fitrianti SugionoPoliteknik Negeri Semarang1
Ignatius Gunawan WidodoPoliteknik Negeri Semarang1
Padang YanuarPoliteknik Negeri Semarang1
Poppy PuspitasariState University of Malang1
Putut MurdantoState University of Malang1
Mohammad Sugi HartonoPoliteknik Negeri Malang1
Remon LapisaUniversitas Negeri Padang1
Jasman JasmanUniversitas Negeri Padang1
Zainal AbadiUniversitas Negeri Padang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.yrpipku.com/index.php/jaets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 9 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Effect of Moisture Content of Green Sand on The Casting Defects </dc:title>
	<dc:creator xml:lang="en">Qosim, Nanang</dc:creator>
	<dc:creator xml:lang="en">Mufarrih, AM</dc:creator>
	<dc:creator xml:lang="en">Sai’in, Ali</dc:creator>
	<dc:creator xml:lang="en">Firdaus, A. Hanif</dc:creator>
	<dc:creator xml:lang="en">Andika F. A., Fina </dc:creator>
	<dc:creator xml:lang="en">Monasari, Ratna</dc:creator>
	<dc:creator xml:lang="en">Emzain, Zakki F.</dc:creator>
	<dc:subject xml:lang="en">sand casting, green sand, moisture content, Al-Si, casting defects</dc:subject>
	<dc:description xml:lang="en">In this study, three percentages of moisture content on the green sand were benchmarked to be observed their effects on the casting defects. The metal used is scrap Al-Si with wt% of Al 59.7. The metal was melted in a furnace at 550 ºC then poured into sand molds and cooled for 24 hours before it can be removed, cleaned, and finished. There were prepared three specimens for each benchmark. Qualitative observation of defects was done by physical observations on the surface of the specimens. The observations show that on the moisture content of 2.5%, there is a defect in the form of porosity. Defects in the form of drops, misruns, blowholes, and shrinkage cavity are found on the benchmark 3.5%. The most severe defects are found on the benchmark 4.5% in the form of buckles and severe shrinkage cavities that are found in almost all specimens.</dc:description>
	<dc:publisher xml:lang="en">Yayasan Riset dan Pengembangan Intelektual (YRPI)</dc:publisher>
	<dc:date>2020-08-06</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.yrpipku.com/index.php/jaets/article/view/77</dc:identifier>
	<dc:identifier>10.37385/jaets.v2i1.77</dc:identifier>
	<dc:source xml:lang="en">Journal of Applied Engineering and Technological Science (JAETS); Vol. 2 No. 1 (2020): Journal of Applied Engineering and Technological Science (JAETS); 1-6</dc:source>
	<dc:source>2715-6079</dc:source>
	<dc:source>2715-6087</dc:source>
	<dc:source>10.37385/jaets.v2i1</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.yrpipku.com/index.php/jaets/article/view/77/82</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2020 Journal of Applied Engineering and Technological Science (JAETS)</dc:rights>
</oai_dc:dc>