Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Sensitivity Study of The Effect Polymer Flooding Parameters to Improve Oil Recovery Using X-Gradient Boosting Algorithm

Journal of Applied Engineering and Technological Science (JAETS) · Vol. 4 No. 2 (2023) · hlm. 873–884

DOI
10.37385/jaets.v4i2.1871
ISSN
2715-6079, 2715-6087
Terbit
2023-06-05
Penerbit
Yayasan Riset dan Pengembangan Intelektual (YRPI)
Bahasa
en

Abstrak

Implementation of waterflooding sometimes cannot increase oil recovery effectively and requires additional methods to increase oil recovery. Polymer flooding is a common chemical EOR method that has been implemented in the last few decades and provides good effectiveness in increasing oil recovery and can reduce the amount of injection fluid injected into the reservoir. Seeing the success of polymer flooding in increasing oil recovery, it is necessary to know the parameters that influence the success of polymer flooding so that it can be evaluated and taken into consideration in creating a new scheme to increase oil recovery with polymer flooding. The parameters tested in this study include Injection Rate, Injection Time, Injection Pressure, Adsorption, Inaccessible Pore Volume, Residual Resistance Factor. This research uses the X-Gardient Boosting Algorithm to look at the most influential parameters in polymer flooding. The parameters that most influence the performance of polymer flooding on the value of oil recovery with the importance level of each parameter in this study are injection time of 0.452632, injection rate of 0.430075, injection pressure of 0.064662, Adsorption of 0.025564, RRF of 0.021053, IPV of 0.006014 and produce accurate predictive modeling using x-gradient boosting where with 3 variations of the comparison ratio of training and testing data obtained at a ratio of 0.7: 0.3 obtained an R2 train of 0.9886 and an R2 test of 0.9645, a ratio of 0.8: 0.2 obtained an R2 train of 0.9891 and an R2 test of 0.9579, and a ratio of 0.9: 0.1 obtained R2 train of 0.9890 and R2 test of 0.9660.

Kata kunci

Jaringan kolaborasi para penulis

24 penulis · 73 tautan kepenulisan bersama · 35 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Islamic University of Riau
  • Bandung Institute of Technology
  • Riau University
  • Universiti Teknologi MARA
  • Sebelas Maret University
  • Universitas Halu Oleo
  • Chulalongkorn University
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Muhammad Khairul AfdholIslamic University of Riau3
Fiki HidayatIslamic University of Riau3
Rika Lala SaputriIslamic University of Riau3
Razif Muhammed NordinUniversiti Teknologi MARA2
Adiella Zakky JuneidRiau University2
Intan PermatasariSebelas Maret University1
Hardiyanto HardiyantoUniversitas Halu Oleo1
Muhammad Yogi SatriaAfiliasi tidak diketahui1
Tengku Mohammad Sofyan AstsauriAfiliasi tidak diketahui1
Bayu Dedi PrasetiyoAfiliasi tidak diketahui1
Gerry SiregarAfiliasi tidak diketahui1
Muslim Darbi AbdurrahmanIslamic University of Riau1
Romal RamadhanChulalongkorn University1
Adi NovriansyahIslamic University of Riau1
Suparit TangparitkulChiang Mai University1
Arik DaniatiBandung Institute of Technology1
Asep Kurnia PermadiBandung Institute of Technology1
Dita Putri PurnamaIslamic University of Riau1
Muhammad Khairul AfdhoAfiliasi tidak diketahui1
Muhammad Salihin ZakariaUniversiti Malaysia Perlis1
MursyidahIslamic University of Riau1
Ari PrasetyoIslamic University of Riau1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.yrpipku.com/index.php/jaets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Sensitivity Study of The Effect Polymer Flooding Parameters to Improve Oil Recovery Using X-Gradient Boosting Algorithm  </dc:title>
	<dc:creator xml:lang="en">Erfando, Tomi</dc:creator>
	<dc:creator xml:lang="en">Khariszma, Rizqy </dc:creator>
	<dc:subject xml:lang="en">X- Gradient Boosting Algorithm</dc:subject>
	<dc:subject xml:lang="en">Polymer Flooding</dc:subject>
	<dc:subject xml:lang="en">Oil Recovery</dc:subject>
	<dc:subject xml:lang="en">energy</dc:subject>
	<dc:description xml:lang="en">Implementation of waterflooding sometimes cannot increase oil recovery effectively and requires additional methods to increase oil recovery. Polymer flooding is a common chemical EOR method that has been implemented in the last few decades and provides good effectiveness in increasing oil recovery and can reduce the amount of injection fluid injected into the reservoir. Seeing the success of polymer flooding in increasing oil recovery, it is necessary to know the parameters that influence the success of polymer flooding so that it can be evaluated and taken into consideration in creating a new scheme to increase oil recovery with polymer flooding. The parameters tested in this study include Injection Rate, Injection Time, Injection Pressure, Adsorption, Inaccessible Pore Volume, Residual Resistance Factor. This research uses the X-Gardient Boosting Algorithm to look at the most influential parameters in polymer flooding. The parameters that most influence the performance of polymer flooding on the value of oil recovery with the importance level of each parameter in this study are injection time of 0.452632, injection rate of 0.430075, injection pressure of 0.064662, Adsorption of 0.025564, RRF of 0.021053, IPV of 0.006014 and produce accurate predictive modeling using x-gradient boosting where with 3 variations of the comparison ratio of training and testing data obtained at a ratio of 0.7 : 0.3 obtained an R2 train of 0.9886 and an R2 test of 0.9645, a ratio of 0.8 : 0.2 obtained an R2 train of 0.9891 and an R2 test of 0.9579, and a ratio of 0.9: 0.1 obtained R2 train of 0.9890 and R2 test of 0.9660.</dc:description>
	<dc:publisher xml:lang="en">Yayasan Riset dan Pengembangan Intelektual (YRPI)</dc:publisher>
	<dc:date>2023-06-05</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.yrpipku.com/index.php/jaets/article/view/1871</dc:identifier>
	<dc:identifier>10.37385/jaets.v4i2.1871</dc:identifier>
	<dc:source xml:lang="en">Journal of Applied Engineering and Technological Science (JAETS); Vol. 4 No. 2 (2023): Journal of Applied Engineering and Technological Science (JAETS); 873-884</dc:source>
	<dc:source>2715-6079</dc:source>
	<dc:source>2715-6087</dc:source>
	<dc:source>10.37385/jaets.v4i2</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.yrpipku.com/index.php/jaets/article/view/1871/1312</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2023 Journal of Applied Engineering and Technological Science (JAETS)</dc:rights>
</oai_dc:dc>