Melola Discovery

← Melola Discovery

Jurnal SINTA 1

The Effect of Quenching With Oil on Annealing Temperature Variations on The Hardness Of ST 37 Equivalent Steel

Journal of Applied Engineering and Technological Science (JAETS) · Vol. 7 No. 2 (2026) · hlm. 1591–1608

DOI
10.37385/jaets.v7i2.10558
ISSN
2715-6079, 2715-6087
Terbit
2026-06-15
Penerbit
Yayasan Riset dan Pengembangan Intelektual (YRPI)
Bahasa
en

Abstrak

ST37 equivalent steel is widely used in engineering applications due to its high ductility; however, its relatively low hardness limits its performance in wear-related components. This study investigates the effect of annealing temperature variations and different oil quenching media on the hardness of ST37 equivalent steel. Specimens were annealed at 750°C, 850°C, and 950°C with a holding time of 10 minutes, followed by quenching in three types of oil: SAE 15W-40 mineral oil, SAE 10W-40 semi-synthetic oil, and SAE 10W-40 fully synthetic oil. Hardness measurements were conducted using the Rockwell B scale (HRB) at five different points on each specimen. The results indicate a consistent increase in hardness with increasing annealing temperature for all quenching media. The highest hardness value, 43.4 HRB, was obtained at 950°C using fully synthetic oil, representing an improvement of approximately 4.58% compared to the untreated material. Among the tested media, fully synthetic oil exhibited the most effective cooling performance. These findings demonstrate that both annealing temperature and oil type significantly influence the hardness characteristics of ST37 equivalent steel.

Kata kunci

Jaringan kolaborasi para penulis

36 penulis · 129 tautan kepenulisan bersama · 21 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Halu Oleo
  • Politeknik Negeri Ketapang
  • Poltekkes Kemenkes Palu
  • Universitas Sulawesi Tenggara
  • Universitas Islam Negeri Mataram
  • Institut Agama Islam Negeri Kendari
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Betti Ses Eka PoloniaPoliteknik Negeri Ketapang4
Asep RuchiyatPoliteknik Negeri Ketapang3
Suhirno SuhirnoUniversitas Halu Oleo2
Rahmat MadjidUniversitas Halu Oleo2
Epriyandi EpriyandiPoliteknik Negeri Ketapang2
Helanianto HelaniantoPoliteknik Negeri Ketapang2
Hairian RahmadiPoliteknik Negeri Ketapang2
Ismael MarjukiPoliteknik Negeri Ketapang2
Dewi NurmayasariPoliteknik Negeri Ketapang2
Efi AmsiAfiliasi tidak diketahui1
Nasrul NasrulPoltekkes Kemenkes Palu1
Murdjani KamaluddinUniversitas Halu Oleo1
Jeanet Silky MeitriUniversitas Halu Oleo1
Nurwati NurwatiUniversitas Halu Oleo1
Yusuf MontunduUniversitas Halu Oleo1
Asrip PuteraUniversitas Halu Oleo1
Ida Bagus Agung Surya AUniversitas Halu Oleo1
Eliyanti Agus MokodompitUniversitas Halu Oleo1
Adnan HakimUniversitas Halu Oleo1
Hartini HartiniUniversitas Halu Oleo1
Riski Amalia MadiUniversitas Halu Oleo1
Juharsah JuharsahUniversitas Halu Oleo1
Hastuti HastutiUniversitas Halu Oleo1
Wahyuniati HamidUniversitas Halu Oleo1
Nindy Ade MarsalenaUniversitas Sulawesi Tenggara1
Alida PalilatiUniversitas Halu Oleo1
Moh. AminUniversitas Halu Oleo1
Muh. Rivan KohawanUniversitas Halu Oleo1
Yusuf YusufUniversitas Halu Oleo1
Muhammad IkhsanInstitut Agama Islam Negeri Kendari1
Hunaepi HunaepiAfiliasi tidak diketahui1
Suhirman SuhirmanUniversitas Islam Negeri Mataram1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.yrpipku.com/index.php/jaets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">The Effect of Quenching With Oil on Annealing Temperature Variations on The Hardness Of ST 37 Equivalent Steel</dc:title>
	<dc:creator xml:lang="en">Anhar, Muh</dc:creator>
	<dc:creator xml:lang="en">Yusuf, Yusuf</dc:creator>
	<dc:creator xml:lang="en">SP, Irianto</dc:creator>
	<dc:creator xml:lang="en">Astriawati, Ningrum</dc:creator>
	<dc:subject xml:lang="en">ST 37 Steel</dc:subject>
	<dc:subject xml:lang="en">Heat Treatment</dc:subject>
	<dc:subject xml:lang="en">Annealing</dc:subject>
	<dc:subject xml:lang="en">Quenching</dc:subject>
	<dc:subject xml:lang="en">Oil Cooling Medium</dc:subject>
	<dc:description xml:lang="en">ST37 equivalent steel is widely used in engineering applications due to its high ductility; however, its relatively low hardness limits its performance in wear-related components. This study investigates the effect of annealing temperature variations and different oil quenching media on the hardness of ST37 equivalent steel. Specimens were annealed at 750°C, 850°C, and 950°C with a holding time of 10 minutes, followed by quenching in three types of oil: SAE 15W-40 mineral oil, SAE 10W-40 semi-synthetic oil, and SAE 10W-40 fully synthetic oil. Hardness measurements were conducted using the Rockwell B scale (HRB) at five different points on each specimen. The results indicate a consistent increase in hardness with increasing annealing temperature for all quenching media. The highest hardness value, 43.4 HRB, was obtained at 950°C using fully synthetic oil, representing an improvement of approximately 4.58% compared to the untreated material. Among the tested media, fully synthetic oil exhibited the most effective cooling performance. These findings demonstrate that both annealing temperature and oil type significantly influence the hardness characteristics of ST37 equivalent steel. </dc:description>
	<dc:publisher xml:lang="en">Yayasan Riset dan Pengembangan Intelektual (YRPI)</dc:publisher>
	<dc:date>2026-06-15</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.yrpipku.com/index.php/jaets/article/view/10558</dc:identifier>
	<dc:identifier>10.37385/jaets.v7i2.10558</dc:identifier>
	<dc:source xml:lang="en">Journal of Applied Engineering and Technological Science (JAETS); Vol. 7 No. 2 (2026): Journal of Applied Engineering and Technological Science (JAETS); 1591-1608</dc:source>
	<dc:source>2715-6079</dc:source>
	<dc:source>2715-6087</dc:source>
	<dc:source>10.37385/jaets.v7i2</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.yrpipku.com/index.php/jaets/article/view/10558/6428</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2026 Muh Anhar, Yusuf Yusuf, Irianto SP, Ningrum Astriawati</dc:rights>
</oai_dc:dc>