Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Effect of V-shaped Ribs on Internal Cooling of Gas Turbine Blades

Journal of Engineering and Technological Sciences · Vol. 49 No. 4 (2017) · hlm. 520–533

DOI
10.5614/j.eng.technol.sci.2017.49.4.7
ISSN
2338-5502, 2337-5779
Terbit
2017-10-31
Penerbit
Directorate for Research and Community Services, Institut Teknologi Bandung
Bahasa
eng

Abstrak

Thermal efficiency and power output of gas turbines increase with increasing turbine rotor inlet temperature. The rotor inlet temperatures in most gas turbines are far higher than the melting point of the blade material. Hence the turbine blades need to be cooled. In this work, simulations were carried out with the leading edge of gas turbine blade being internally cooled by coolant passages with V-shaped ribs at angles of 30°, 45° or 60° and at three aspect ratios (1:1, 1:2 and 2:3). The trailing edge of the blade was cooled by cylindrical and triangular pin-fin perforations in staggered and inline arrangements. Numerical analyses were carried out for each configuration of the cooling passages. The best cooling passages for leading edge and trailing edge were deduced by comparing the results of these analyses. It was found that using V-shaped ribs and fins induces a swirling flow, which in turn increases the velocity gradient and hence produces an improvement in heat transfer. The results show that under real time flow conditions, the application of V-shaped ribs and pin-fin perforations is a very promising technique for improving blade life.

Kata kunci

Jaringan kolaborasi para penulis

11 penulis · 21 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Manipal Academy of Higher Education
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Anand PaiManipal Academy of Higher Education2
Pradyumna KodanchaManipal Academy of Higher Education1
Rajesh K BayarAfiliasi tidak diketahui1
Gaurav GulabaniManipal Academy of Higher Education1
Beegum Shahnaz Abdul KarimManipal Academy of Higher Education1
Jayakrishnan RadhakrishnanManipal Academy of Higher Education1
Mohammad ZuberManipal Academy of Higher Education1
Laxmikant G. KeniManipal Academy of Higher Education1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journals.itb.ac.id/index.php/jets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Effect of V-shaped Ribs on Internal Cooling of Gas Turbine Blades</dc:title>
	<dc:creator>Kamat, Harishkumar</dc:creator>
	<dc:creator>Shenoy, Satish B.</dc:creator>
	<dc:creator>Kini, Chandrakant R</dc:creator>
	<dc:subject xml:lang="en-US">Leading edge</dc:subject>
	<dc:subject xml:lang="en-US">internal cooling</dc:subject>
	<dc:subject xml:lang="en-US">ribs</dc:subject>
	<dc:subject xml:lang="en-US">trailing edge</dc:subject>
	<dc:subject xml:lang="en-US">turbine blade cooling.</dc:subject>
	<dc:description xml:lang="en-US">Thermal efficiency and power output of gas turbines increase with increasing turbine rotor inlet temperature. The rotor inlet temperatures in most gas turbines are far higher than the melting point of the blade material. Hence the turbine blades need to be cooled. In this work, simulations were carried out with the leading edge of gas turbine blade being internally cooled by coolant passages with V-shaped ribs at angles of 30°, 45° or 60° and at three aspect ratios (1:1, 1:2 and 2:3). The trailing edge of the blade was cooled by cylindrical and triangular pin-fin perforations in staggered and inline arrangements. Numerical analyses were carried out for each configuration of the cooling passages. The best cooling passages for leading edge and trailing edge were deduced by comparing the results of these analyses. It was found that using V-shaped ribs and fins induces a swirling flow, which in turn increases the velocity gradient and hence produces an improvement in heat transfer. The results show that under real time flow conditions, the application of V-shaped ribs and pin-fin perforations is a very promising technique for improving blade life. </dc:description>
	<dc:publisher xml:lang="en-US">Directorate for Research and Community Services, Institut Teknologi Bandung</dc:publisher>
	<dc:date>2017-10-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journals.itb.ac.id/index.php/jets/article/view/4100</dc:identifier>
	<dc:identifier>10.5614/j.eng.technol.sci.2017.49.4.7</dc:identifier>
	<dc:source xml:lang="en-US">Journal of Engineering and Technological Sciences; Vol. 49 No. 4 (2017); 520-533</dc:source>
	<dc:source>2338-5502</dc:source>
	<dc:source>2337-5779</dc:source>
	<dc:source>10.5614/j.eng.technol.sci.2017.49.4</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://journals.itb.ac.id/index.php/jets/article/view/4100/2992</dc:relation>
</oai_dc:dc>