Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Properties and Performance of Gas Diffusion Layer PEMFC Derived from Coconut Coir

Journal of Engineering and Technological Sciences · Vol. 50 No. 3 (2018) · hlm. 409–419

DOI
10.5614/j.eng.technol.sci.2018.50.3.7
ISSN
2338-5502, 2337-5779
Terbit
2018-08-31
Penerbit
Directorate for Research and Community Services, Institut Teknologi Bandung
Bahasa
eng

Abstrak

In this work, carbon composite papers (CCP) were successfully produced by mixing 80 wt% carbon derived from coconut coir and 20 wt% binder (ethylene vinyl acetate and polyethylene glycol). The CCPs were prepared with two different forms of carbon material, i.e. powder (particle size: ± 74 µm) and fiber (length: ± 2 mm, diameter: 100-500 µm). Two types of papers were developed based on their composition. The first type, called CCP-1, was made from carbon in powder form (80 wt%), while the second one, CCP-2, was based on a combination of fiber (70 wt%) and powder (10 wt%). The influence of the carbon form on CCP properties were investigated, including electrical conductivity, porosity, hydrophobicity, microstructure, and its performance as a gas diffusion layer (GDL) in a stack of proton exchange membrane fuel cell (PEMFC) system. Based on the results, CCP-1 showed a slightly better fuel cell performance than CCP-2, which was also confirmed by its lower porosity, electrical conductivity, and water contact angle. The effect of carbon composite paper's properties, including its morphology and performance, are disscused in this paper in detail and compared with a commercially based GDL material (TGP-H-120).

Kata kunci

Jaringan kolaborasi para penulis

25 penulis · 62 tautan kepenulisan bersama · 27 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Indonesian Institute of Sciences
  • National Research and Innovation Agency
  • Mercu Buana University
  • Tun Hussein Onn University of Malaysia
  • National Nuclear Energy Agency of Indonesia
  • Sunan Gunung Djati State Islamic University Bandung
  • University of Mataram
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Indriyati IndriyatiIndonesian Institute of Sciences1
Tita PuspitasariNational Nuclear Energy Agency of Indonesia1
Sudirman SudirmanUniversity of Mataram1
Rike YudiantiNational Research and Innovation Agency1
Shofia ManzaliniSunan Gunung Djati State Islamic University Bandung1
Bambang SugengNational Research and Innovation Agency1
Harayasu AsaharaThe University of Osaka1
Jarot RaharjoAfiliasi tidak diketahui1
Ade Utami HapsariAfiliasi tidak diketahui1
Retna Deca PravitasariAfiliasi tidak diketahui1
Hanif YulianiAfiliasi tidak diketahui1
Damisih DamisihAfiliasi tidak diketahui1
Aghni Ulma SaudiAfiliasi tidak diketahui1
Wahyu Mulyo UtomoTun Hussein Onn University of Malaysia1
Afarulrazi Abu BakarTun Hussein Onn University of Malaysia1
Triyanto PangaribowoMercu Buana University1
Abdul Hamid BudimanNational Research and Innovation Agency1
Bambang MulyantoMercu Buana University1
Dani Tri WahyudiIndonesian Institute of Sciences1
Desi FajarwatiMercu Buana University1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journals.itb.ac.id/index.php/jets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Properties and Performance of Gas Diffusion Layer PEMFC Derived from Coconut Coir</dc:title>
	<dc:creator>Destyorini, Fredina</dc:creator>
	<dc:creator>Irmawati, Yuyun</dc:creator>
	<dc:creator>Widodo, Henry</dc:creator>
	<dc:creator>Khaerudini, Deni Shidqi</dc:creator>
	<dc:creator>Indayaningsih, Nanik</dc:creator>
	<dc:subject xml:lang="en-US">cell performance</dc:subject>
	<dc:subject xml:lang="en-US">coconut coir</dc:subject>
	<dc:subject xml:lang="en-US">electrical conductivity</dc:subject>
	<dc:subject xml:lang="en-US">fuel cell</dc:subject>
	<dc:subject xml:lang="en-US">gas diffusion layer.</dc:subject>
	<dc:description xml:lang="en-US">In this work, carbon composite papers (CCP) were successfully produced by mixing 80 wt% carbon derived from coconut coir and 20 wt% binder (ethylene vinyl acetate and polyethylene glycol). The CCPs were prepared with two different forms of carbon material, i.e. powder (particle size: ± 74 µm) and fiber (length: ± 2 mm, diameter: 100-500 µm). Two types of papers were developed based on their composition. The first type, called CCP-1, was made from carbon in powder form (80 wt%), while the second one, CCP-2, was based on a combination of fiber (70 wt%) and powder (10 wt%). The influence of the carbon form on CCP properties were investigated, including electrical conductivity, porosity, hydrophobicity, microstructure, and its performance as a gas diffusion layer (GDL) in a stack of proton exchange membrane fuel cell (PEMFC) system. Based on the results, CCP-1 showed a slightly better fuel cell performance than CCP-2, which was also confirmed by its lower porosity, electrical conductivity, and water contact angle. The effect of carbon composite paper's properties, including its morphology and performance, are disscused in this paper in detail and compared with a commercially based GDL material (TGP-H-120).</dc:description>
	<dc:publisher xml:lang="en-US">Directorate for Research and Community Services, Institut Teknologi Bandung</dc:publisher>
	<dc:date>2018-08-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journals.itb.ac.id/index.php/jets/article/view/6431</dc:identifier>
	<dc:identifier>10.5614/j.eng.technol.sci.2018.50.3.7</dc:identifier>
	<dc:source xml:lang="en-US">Journal of Engineering and Technological Sciences; Vol. 50 No. 3 (2018); 409-419</dc:source>
	<dc:source>2338-5502</dc:source>
	<dc:source>2337-5779</dc:source>
	<dc:source>10.5614/j.eng.technol.sci.2018.50.3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://journals.itb.ac.id/index.php/jets/article/view/6431/3458</dc:relation>
</oai_dc:dc>