Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Effect of Temperature, Holding Time, and Addition of Sn on Density on Metal Injection Molding Sintering Process

Journal of Engineering and Technological Sciences · Vol. 55 No. 2 (2023) · hlm. 143–152

DOI
10.5614/j.eng.technol.sci.2023.55.2.4
ISSN
2338-5502, 2337-5779
Terbit
2023-05-24
Penerbit
Directorate for Research and Community Services, Institut Teknologi Bandung
Bahasa
eng

Abstrak

Metal injection molding (MIM) is a metal forming technique that combines powder metallurgy with plastic injection molding. MIM is very efficient in manufacturing small and complex products in large quantities. The MIM process has four steps: mixing, debinding, injection molding, and sintering. This research was conducted to determine the effect of variations in Sn addition, temperature, and holding time on the density of Al-PP products after the sintering process. Density is mass per volume so to find out the volume of Al-PP products, the use of a 3D scanner was attempted along with the EinScan application and a mesh mixer. The Taguchi method was used for data processing to determine the influence of variations in Sn addition, temperature, and holding time on density. The calculation of the percentage contribution showed that variations in Sn addition, temperature, and holding time affected density by 47%, 21%, and 3%. Also, 2% Sn addition yielded a reasonably good microstructure formation compared to without Sn addition and 1% Sn addition, where many voids remained in the specimen (the more significant the voids, the lower the density).

Kata kunci

Jaringan kolaborasi para penulis

29 penulis · 86 tautan kepenulisan bersama · 21 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Jember
  • Bandung Institute of Technology
  • Sriwijaya University
  • Sacred Heart College
  • University of Technology Malaysia
  • Papua New Guinea University of Technology
  • Universitas Halu Oleo
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Salahuddin JunusUniversitas Jember3
Revvan Rifada PradizaUniversitas Jember3
Muhammad YusufUniversitas Halu Oleo2
Gaguk JatisukamtoAfiliasi tidak diketahui2
Laily Ilman WiduriSriwijaya University1
Tri HandoyoAfiliasi tidak diketahui1
Gindeka Bimara AryantakaUniversitas Jember1
Rizky Akhmad PrayogiUniversitas Jember1
Rahma Rei SakuraUniversitas Jember1
R. Puranggo Ganjar WidityoUniversitas Jember1
Robertus SidartawanUniversitas Jember1
Muhammad YusufUniversitas Jember1
Midhun Dominic C. D.Sacred Heart College1
R.A. IlyasUniversity of Technology Malaysia1
Boy Arief FachriUniversitas Jember1
Mochamad Edoward RamadhanUniversitas Jember1
Renald Rochman MauludyUniversitas Jember1
Intan HardiatamaUniversitas Jember1
Doddy ParningotanAfiliasi tidak diketahui1
Ivan Fadilla RamadhanUniversitas Jember1
Sumarji SumarjiUniversitas Jember1
Dedi DwilaksanaUniversitas Jember1
Hary SutjahjonoUniversitas Jember1
Steve Korakan AlesPapua New Guinea University of Technology1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journals.itb.ac.id/index.php/jets/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Effect of Temperature, Holding Time, and Addition of Sn on Density on Metal Injection Molding Sintering Process</dc:title>
	<dc:creator>Jannah, Wardatul</dc:creator>
	<dc:creator>Yudistiro, Danang</dc:creator>
	<dc:creator>Asrofi, Mochamad</dc:creator>
	<dc:creator>Darsin, Mahros</dc:creator>
	<dc:creator>Maulana, Ahmad Rendi</dc:creator>
	<dc:subject xml:lang="en-US">3D scanner</dc:subject>
	<dc:subject xml:lang="en-US">metal injection molding</dc:subject>
	<dc:subject xml:lang="en-US">sintering</dc:subject>
	<dc:subject xml:lang="en-US">Sn</dc:subject>
	<dc:subject xml:lang="en-US">Taguchi</dc:subject>
	<dc:subject xml:lang="en-US">Mechanical Engineering</dc:subject>
	<dc:description xml:lang="en-US">Metal injection molding (MIM) is a metal forming technique that combines powder metallurgy with plastic injection molding. MIM is very efficient in manufacturing small and complex products in large quantities. The MIM process has four steps: mixing, debinding, injection molding, and sintering. This research was conducted to determine the effect of variations in Sn addition, temperature, and holding time on the density of Al-PP products after the sintering process. Density is mass per volume so to find out the volume of Al-PP products, the use of a 3D scanner was attempted along with the EinScan application and a mesh mixer. The Taguchi method was used for data processing to determine the influence of variations in Sn addition, temperature, and holding time on density. The calculation of the percentage contribution showed that variations in Sn addition, temperature, and holding time affected density by 47%, 21%, and 3%. Also, 2% Sn addition yielded a reasonably good microstructure formation compared to without Sn addition and 1% Sn addition, where many voids remained in the specimen (the more significant the voids, the lower the density).</dc:description>
	<dc:publisher xml:lang="en-US">Directorate for Research and Community Services, Institut Teknologi Bandung</dc:publisher>
	<dc:date>2023-05-24</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journals.itb.ac.id/index.php/jets/article/view/18780</dc:identifier>
	<dc:identifier>10.5614/j.eng.technol.sci.2023.55.2.4</dc:identifier>
	<dc:source xml:lang="en-US">Journal of Engineering and Technological Sciences; Vol. 55 No. 2 (2023); 143-152</dc:source>
	<dc:source>2338-5502</dc:source>
	<dc:source>2337-5779</dc:source>
	<dc:source>10.5614/j.eng.technol.sci.2023.55.2</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://journals.itb.ac.id/index.php/jets/article/view/18780/6211</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2023 Journal of Engineering and Technological Sciences</dc:rights>
</oai_dc:dc>