Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Chemical Anchor Pullout Force Modeling with Variation of Anchor Embedment Length in Concrete and Concrete Strength

Journal of the Civil Engineering Forum · Vol. 8 No. 3 (2022) · hlm. 277–290

DOI
10.22146/jcef.3769
ISSN
2549-5925, 2581-1037
Terbit
2022-07-28
Penerbit
Department of Civil and Environmental Engineering, Faculty of Engineering, Universitas Gadjah Mada
Bahasa
eng

Abstrak

The embedment length influences the adhesion between the cast iron material and the concrete. The concrete's compression strength also contributes to an increase in bond strength. Therefore, this research aims to determine the maximum pullout force on each variation of the anchor and the optimal embedment length. A gauge is modeled as a rod-type with a diameter of 16 mm, and the embedment lengths used are 5D, 10D, and 15D, while the compressive strengths include fc’ 20, 30, 40, 50, and 60 MPa. Furthermore, a finite element-based application was utilized with the ANSYS Workbench student version. The result showed that the concrete with strengths of 20, 30, 40, 50, and 60 MPa has maximum pullout forces of 27.011, 53.536, 68.657, 68.970, and 84.407 kN, respectively at an embedment length of 15D. It was observed that the failure pattern obtained starts from the defect in the concrete cone and ends with the breakage of reinforcement or steel failure at each variation of concrete strength. A combination of two non-parametric techniques was used in this research, which includes Kruskal Wallis and U-Mann Whitney test. The first technique revealed that the chi-square value for strengths 20, 40, 50, and 60 MPa is 9.486, while that of 30 MPa is 9.881. The second test employed showed a significance value below 0.05. In conclusion, the embedment length affected the value of pullout force, and 15D was the optimum embedment length for each variation of concrete strength. The enhancement in tensile strength increases with the strength of the concrete.

Kata kunci

Jaringan kolaborasi para penulis

12 penulis · 22 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Jakarta State Polytechnic
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
I Ketut SucitaJakarta State Polytechnic5
Hanif Satria AjiJakarta State Polytechnic2
Oky Bima PutraJakarta State Polytechnic2
Ilham Dwiputra RamadhanJakarta State Polytechnic2
Tree Irma DindaJakarta State Polytechnic2
Alvin DunaufalJakarta State Polytechnic1
Hanan YurizkaJakarta State Polytechnic1
Nadhila Ramadhani A.P.Jakarta State Polytechnic1
Annisaa Dina PuspitaJakarta State Polytechnic1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://jurnal.ugm.ac.id/v3/jcef/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Chemical Anchor Pullout Force Modeling with Variation of Anchor Embedment Length in Concrete and Concrete Strength</dc:title>
	<dc:creator>Rosyidah, Anis</dc:creator>
	<dc:creator>Widiana Putra, Jasun </dc:creator>
	<dc:creator>Saputra, Jonathan</dc:creator>
	<dc:subject xml:lang="en-US">Maximum Axial Force</dc:subject>
	<dc:subject xml:lang="en-US">Embedment Length</dc:subject>
	<dc:subject xml:lang="en-US">Concrete Strength</dc:subject>
	<dc:subject xml:lang="en-US">Finite Elements</dc:subject>
	<dc:subject xml:lang="en-US">Statistics</dc:subject>
	<dc:description xml:lang="en-US">The embedment length influences the adhesion between the cast iron material and the concrete. The concrete's compression strength also contributes to an increase in bond strength. Therefore, this research aims to determine the maximum pullout force on each variation of the anchor and the optimal embedment length. A gauge is modeled as a rod-type with a diameter of 16 mm, and the embedment lengths used are 5D, 10D, and 15D, while the compressive strengths include fc’ 20, 30, 40, 50, and 60 MPa. Furthermore, a finite element-based application was utilized with the ANSYS Workbench student version. The result showed that the concrete with strengths of 20, 30, 40, 50, and 60 MPa has maximum pullout forces of 27.011, 53.536, 68.657, 68.970, and 84.407 kN, respectively at an embedment length of 15D. It was observed that the failure pattern obtained starts from the defect in the concrete cone and ends with the breakage of reinforcement or steel failure at each variation of concrete strength. A combination of two non-parametric techniques was used in this research, which includes Kruskal Wallis and U-Mann Whitney test. The first technique revealed that the chi-square value for strengths 20, 40, 50, and 60 MPa is 9.486, while that of 30 MPa is 9.881. The second test employed showed a significance value below 0.05. In conclusion, the embedment length affected the value of pullout force, and 15D was the optimum embedment length for each variation of concrete strength. The enhancement in tensile strength increases with the strength of the concrete.</dc:description>
	<dc:publisher xml:lang="en-US">Department of Civil and Environmental Engineering, Faculty of Engineering, Universitas Gadjah Mada</dc:publisher>
	<dc:date>2022-07-28</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://jurnal.ugm.ac.id/v3/JCEF/article/view/3769</dc:identifier>
	<dc:identifier>10.22146/jcef.3769</dc:identifier>
	<dc:source xml:lang="en-US">Journal of the Civil Engineering Forum; Vol. 8 No. 3 (September 2022); 277-290</dc:source>
	<dc:source>2549-5925</dc:source>
	<dc:source>2581-1037</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://jurnal.ugm.ac.id/v3/JCEF/article/view/3769/1810</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2022 The Author(s)</dc:rights>
</oai_dc:dc>