Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Unconfined Compressive Strength and Damage Evolution in Geopolymer-Stabilized Clay Shale: Role of Temperature and Alkali Activator Ratio

Journal of the Civil Engineering Forum · Vol. 12 No. 2 (2026) · hlm. 255–266

DOI
10.22146/jcef.22477
ISSN
2549-5925, 2581-1037
Terbit
2026-04-18
Penerbit
Department of Civil and Environmental Engineering, Faculty of Engineering, Universitas Gadjah Mada
Bahasa
eng

Abstrak

Exposed clay shale is highly susceptible to weathering and rapid strength degradation, which often leads to slope and earth-structure instability. Geopolymer-based soil stabilization has emerged as a promising method to improve the mechanical properties of such problematic materials. However, this chemical stabilization process is sensitive to environmental conditions, particularly temperature fluctuations. The performance of geopolymer-stabilized clay shale under elevated-temperature conditions remains insufficiently investigated, particularly in tropical regions such as Indonesia, where temperatures can fluctuate between 25◦C and 40◦C, and the exposed ground surface may reach up to 60◦C during the dry season because of intense solar radiation. This study evaluates the effectiveness of fly ash–based geopolymer in stabilizing clay shale under temperature variations ranging from 26◦C to 60◦C. A series of laboratory experiments was conducted using two alkali activator ratios (Na2SiO3:NaOH), namely 2.0 (Ratio A) and 2.5 (Ratio B). Mechanical performance was assessed through unconfined compressive strength (UCS) tests, stress–strain analysis, and energy-based damage evolution to quantify strength development and failure behavior. The results indicate that temperature is the dominant factor controlling strength development. A 10◦C increase in curing temperature resulted in a 40–60% increase in UCS, whereas variations in the alkali activator ratio produced only a 15–20% increase. The highest strength amplification, reaching 16 times that of untreated soil, was achieved using Ratio B at 60◦C, while Ratio A showed strength stagnation above 50◦C. Microstructural observations suggest that elevated temperatures accelerate geopolymer gel formation, leading to higher initial stiffness and an expanded elastic region. However, this also resulted in more brittle behavior, characterized by a higher brittleness index and rapid post-peak damage propagation for Ratio B, whereas Ratio A exhibited greater ductility. Overall, higher curing temperatures increased the dissipated energy at failure and revealed a clear strength–ductility trade-off. These findings provide insights for optimizing geopolymer stabilization of clay shale, particularly for geotechnical applications in tropical environments where elevated in situ temperatures are common.

Kata kunci

Jaringan kolaborasi para penulis

19 penulis · 41 tautan kepenulisan bersama · 19 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Muhammadiyah University of Yogyakarta
  • Universitas Jambi
  • Politeknik Negeri Tanah Laut
  • National Taiwan University of Science and Technology
  • Andalas University
  • Kyoto University
  • Kasetsart University
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Abd. Dzargifar HemetoAfiliasi tidak diketahui3
Muhammad AzharPoliteknik Negeri Tanah Laut3
Lia IndrianiMuhammadiyah University of Yogyakarta3
Jazaul IkhsanMuhammadiyah University of Yogyakarta2
Wilis DianaMuhammadiyah University of Yogyakarta2
Anita RahmawatiMuhammadiyah University of Yogyakarta2
Liao H.J.National Taiwan University of Science and Technology1
Rehni SetiatiAndalas University1
Ryosuke UzuokaKyoto University1
Nurul FataMuhammadiyah University of Yogyakarta1
Apiniti JotisankasaKasetsart University1
Kuo‐Hsin YangNational Taiwan University1
Ani HairaniMuhammadiyah University of Yogyakarta1
Muhammad Fikri PermanaMuhammadiyah University of Yogyakarta1
Farid Nur BahtiMuhammadiyah University of Yogyakarta1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://jurnal.ugm.ac.id/v3/jcef/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Unconfined Compressive Strength and Damage Evolution in Geopolymer-Stabilized Clay Shale: Role of Temperature and Alkali Activator Ratio</dc:title>
	<dc:creator>Diana, Willis</dc:creator>
	<dc:creator>Hartono, Edi</dc:creator>
	<dc:creator>Muntohar, Agus Setyo </dc:creator>
	<dc:creator>Abiyoga, Nurza Purwa </dc:creator>
	<dc:subject xml:lang="en-US">Alkali Activator Ratio</dc:subject>
	<dc:subject xml:lang="en-US">Clay Shale</dc:subject>
	<dc:subject xml:lang="en-US">Damage Properties</dc:subject>
	<dc:subject xml:lang="en-US">Geopolymer Stabilization</dc:subject>
	<dc:subject xml:lang="en-US">Temperature</dc:subject>
	<dc:description xml:lang="en-US">Exposed clay shale is highly susceptible to weathering and rapid strength degradation, which often leads to slope and earth-structure instability. Geopolymer-based soil stabilization has emerged as a promising method to improve the mechanical properties of such problematic materials. However, this chemical stabilization process is sensitive to environmental conditions, particularly temperature fluctuations. The performance of geopolymer-stabilized clay shale under elevated-temperature conditions remains insufficiently investigated, particularly in tropical regions such as Indonesia, where temperatures can fluctuate between 25◦C and 40◦C, and the exposed ground surface may reach up to 60◦C during the dry season because of intense solar radiation. This study evaluates the effectiveness of fly ash–based geopolymer in stabilizing clay shale under temperature variations ranging from 26◦C to 60◦C. A series of laboratory experiments was conducted using two alkali activator ratios (Na2SiO3:NaOH), namely 2.0 (Ratio A) and 2.5 (Ratio B). Mechanical performance was assessed through unconfined compressive strength (UCS) tests, stress–strain analysis, and energy-based damage evolution to quantify strength development and failure behavior. The results indicate that temperature is the dominant factor controlling strength development. A 10◦C increase in curing temperature resulted in a 40–60% increase in UCS, whereas variations in the alkali activator ratio produced only a 15–20% increase. The highest strength amplification, reaching 16 times that of untreated soil, was achieved using Ratio B at 60◦C, while Ratio A showed strength stagnation above 50◦C. Microstructural observations suggest that elevated temperatures accelerate geopolymer gel formation, leading to higher initial stiffness and an expanded elastic region. However, this also resulted in more brittle behavior, characterized by a higher brittleness index and rapid post-peak damage propagation for Ratio B, whereas Ratio A exhibited greater ductility. Overall, higher curing temperatures increased the dissipated energy at failure and revealed a clear strength–ductility trade-off. These findings provide insights for optimizing geopolymer stabilization of clay shale, particularly for geotechnical applications in tropical environments where elevated in situ temperatures are common.</dc:description>
	<dc:publisher xml:lang="en-US">Department of Civil and Environmental Engineering, Faculty of Engineering, Universitas Gadjah Mada</dc:publisher>
	<dc:date>2026-04-18</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://jurnal.ugm.ac.id/v3/JCEF/article/view/22477</dc:identifier>
	<dc:identifier>10.22146/jcef.22477</dc:identifier>
	<dc:source xml:lang="en-US">Journal of the Civil Engineering Forum; Vol. 12 No. 2 (May 2026); 255-266</dc:source>
	<dc:source>2549-5925</dc:source>
	<dc:source>2581-1037</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://jurnal.ugm.ac.id/v3/JCEF/article/view/22477/6981</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2026 The Author(s)</dc:rights>
</oai_dc:dc>