Melola Discovery

← Melola Discovery

Jurnal SINTA 1

A Report on Metal Forming Technology Transfer from Expert to Industry for Improving Production Efficiency

Mechanical Engineering for Society and Industry · Vol. 1 No. 2 (2021) · hlm. 96–103

DOI
10.31603/mesi.5613
ISSN
2798-5245
Terbit
2021-11-23
Penerbit
Universitas Muhammadiyah Magelang
Bahasa
en

Abstrak

This article reports on technological mastery assistance in three small metal forming industries in Indonesia. Problems in the blangking and piercing separately process caused increased production time which resulted in inefficiency cost. Therefore, the expert team aided in metal forming technology through participatory action research (PAR) methods and experimental methods through reverse engineering for several products. The PAR method involves optimal contribution and participation from the industry. Assistance in mastering technology in small metal-forming industries reduces the manufacturing process from seven to three stages, increasing efficiency. The press machine's tonnage capacity must balance with the force blanking/piercing requirement. The minimum press machine requirement is 6.7 tons, and based on the availability of existing press machines, the expert team recommends a 20-ton capacity press machine. Total efficiency can be further increased by implementing full progressive die technology by combining piercing, blanking, and bending processes.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 124 tautan kepenulisan bersama · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • International Islamic University, Islamabad
  • Universitas Halu Oleo
  • Sunan Kalijaga State Islamic University Yogyakarta
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Apang Djafar ShieddiequeAfiliasi tidak diketahui9
Dede Ardi RajabAfiliasi tidak diketahui6
Nazar FazrinAfiliasi tidak diketahui5
Yulfian AminandaAfiliasi tidak diketahui4
Muhamad Taufik UlhakimAfiliasi tidak diketahui4
Tomas IrfaniAfiliasi tidak diketahui4
Afif HakimAfiliasi tidak diketahui4
Rachmat Abdul GaniAfiliasi tidak diketahui3
Amir AmirUniversitas Halu Oleo3
Renata Lintang AzizahAfiliasi tidak diketahui3
Suwardi SuwardiAfiliasi tidak diketahui2
Septa PrimanandaAfiliasi tidak diketahui2
Herry WirianataAfiliasi tidak diketahui2
Yiyi SulaemanAfiliasi tidak diketahui2
Edi YatnoAfiliasi tidak diketahui2
Bertika KusumaAfiliasi tidak diketahui1
Ibnu FatkhuAfiliasi tidak diketahui1
Subaidi SubaidiSunan Kalijaga State Islamic University Yogyakarta1
Muhammad KhoiruddinAfiliasi tidak diketahui1
Mohamad Rifqi RoosdhaniAfiliasi tidak diketahui1
Abdulaziz KalupaeAfiliasi tidak diketahui1
Ibrahim TehhaeeAfiliasi tidak diketahui1
Noorsafuan Bin Che Noh FeloAfiliasi tidak diketahui1
SuwardiAfiliasi tidak diketahui1
Win Listyaningrum ArifinAfiliasi tidak diketahui1
Lilis SetyaningsihAfiliasi tidak diketahui1
Ach MuzammilAfiliasi tidak diketahui1
syamsudin syamsudinAfiliasi tidak diketahui1
Muhammad Fauzaan Fikri Sudarjat SudarjatAfiliasi tidak diketahui1
Enjang MuaheminAfiliasi tidak diketahui1
Farid MajediAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.unimma.ac.id/index.php/mesi/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 9 Nov 2026.
Metadata asli (oai_dc) 
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">A Report on Metal Forming Technology Transfer from Expert to Industry for Improving Production Efficiency</dc:title>
	<dc:creator xml:lang="en">Khoirudin, Khoirudin</dc:creator>
	<dc:creator xml:lang="en">Sukarman, Sukarman</dc:creator>
	<dc:creator xml:lang="en">Murtalim, Murtalim</dc:creator>
	<dc:creator xml:lang="en">Dewadi, Fathan Mubina</dc:creator>
	<dc:creator xml:lang="en">Rahdiana, Nana</dc:creator>
	<dc:creator xml:lang="en">Rais, Amin</dc:creator>
	<dc:creator xml:lang="en">Abdulah, Amri</dc:creator>
	<dc:creator xml:lang="en">Anwar, Choirul</dc:creator>
	<dc:creator xml:lang="en">Abbas, Aries</dc:creator>
	<dc:subject xml:lang="en">Blanking and piercing</dc:subject>
	<dc:subject xml:lang="en">Metal forming</dc:subject>
	<dc:subject xml:lang="en">Progressives die</dc:subject>
	<dc:subject xml:lang="en">Reverse engineering</dc:subject>
	<dc:subject xml:lang="en">Technology dissemination</dc:subject>
	<dc:description xml:lang="en">This article reports on technological mastery assistance in three small metal forming industries in Indonesia. Problems in the blangking and piercing separately process caused increased production time which resulted in inefficiency cost. Therefore, the expert team aided in metal forming technology through participatory action research (PAR) methods and experimental methods through reverse engineering for several products. The PAR method involves optimal contribution and participation from the industry. Assistance in mastering technology in small metal-forming industries reduces the manufacturing process from seven to three stages, increasing efficiency. The press machine's tonnage capacity must balance with the force blanking/piercing requirement. The minimum press machine requirement is 6.7 tons, and based on the availability of existing press machines, the expert team recommends a 20-ton capacity press machine. Total efficiency can be further increased by implementing full progressive die technology by combining piercing, blanking, and bending processes.</dc:description>
	<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
	<dc:date>2021-11-23</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unimma.ac.id/mesi/article/view/5613</dc:identifier>
	<dc:identifier>10.31603/mesi.5613</dc:identifier>
	<dc:source xml:lang="en">Mechanical Engineering for Society and Industry; Vol. 1 No. 2 (2021); 96-103</dc:source>
	<dc:source>2798-5245</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unimma.ac.id/mesi/article/view/5613/2840</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2021 Khoirudin Khoirudin, Sukarman Sukarman, Murtalim Murtalim, Fathan Mubina Dewadi, Nana Rahdiana, Amin Rais, Amri Abdulah, Choirul Anwar, Aries Abbas</dc:rights>
</oai_dc:dc>