Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Tensile shear load in resistance spot welding of dissimilar metals: An optimization study using response surface methodology

Mechanical Engineering for Society and Industry · Vol. 3 No. 2 (2023) · hlm. 66–77

DOI
10.31603/mesi.9606
ISSN
2798-5245
Terbit
2023-09-11
Penerbit
Universitas Muhammadiyah Magelang
Bahasa
en

Abstrak

Resistance spot welding (RSW) is being applied extensively in different industries, specifically the automotive sector. Therefore, this study was conducted to optimize the tensile strength load (TSL) in RSW by investigating the application of dissimilar materials as input parameters. The optimization process involved the combination of different galvanized and non-galvanized steel materials. The production of car bodies using galvanized steel with approximately 13.0 microns thick zinc (Zn) coating was found to be a standard practice, but this zinc layer usually presents challenges due to the poor weldability. This study prepared 27 units of TSL samples using a spot-welding machine and a pressure force system (PFS) for the electrode tip. The aim was to determine the optimal TSL through the exploration of specified RSW parameters. The process focused on using the response surface methodology (RSM) to achieve the desired outcome while the Box-Behnken design was applied to determine the input parameters. The optimal TSL obtained was 5265.15 N by setting the squeeze time to 21.0 cycles at a welding current of 24.5 kA, a welding time of 0.5 s, and a holding time of 15.0 cycles. The highest TSL value recorded was 5937.94 N at 21.0 cycles, 27.0 kA, 0.6 s, and 15.0 cycles respectively. These findings were considered significant to the enhancement of productivity across industries, specifically in the RSW process. However, further study was required to investigate additional response variables such as the changes in hardness and microstructure.

Kata kunci

Jaringan kolaborasi para penulis

38 penulis · 154 tautan kepenulisan bersama · 84 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Buana Perjuangan Karawang
  • Sebelas Maret University
  • Sekolah Tinggi Teknologi Wastukancana
  • Indonesia University of Education
  • Universitas Halu Oleo
  • Bandung Institute of Technology
  • Universitas Muhammadiyah Magelang
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Khoirudin KhoirudinUniversitas Buana Perjuangan Karawang4
Apang Djafar ShieddiequeSekolah Tinggi Teknologi Wastukancana2
Muhamad Taufik UlhakimUniversitas Buana Perjuangan Karawang2
Tomas IrfaniUniversitas Buana Perjuangan Karawang2
Afif HakimUniversitas Buana Perjuangan Karawang2
Azizah AzizahIndonesia University of Education2
Muji SetiyoUniversitas Muhammadiyah Magelang2
Amir AmirUniversitas Buana Perjuangan Karawang2
Nazar FahrizinUniversitas Buana Perjuangan Karawang2
W.H. AzmiUniversiti Malaysia Pahang Al-Sultan Abdullah2
Jahidin JahidinUniversitas Halu Oleo1
Al RubaiynUniversitas Halu Oleo1
Muhammad AmirAfiliasi tidak diketahui1
Muhammad Hasan BasriSam Ratulangi University1
Yulfian AminandaUniversiti Teknologi Brunei1
Mardiyati MardiyatiBandung Institute of Technology1
Bambang WidyantoBandung Institute of Technology1
Saifudin SaifudinUniversitas Muhammadiyah Magelang1
Nurul MuhayatSebelas Maret University1
Eko SurojoSebelas Maret University1
Yupiter HP ManurungUniversiti Teknologi MARA1
Sukarman SukarmanSekolah Tinggi Teknologi Wastukancana1
Fajar MucharromAfiliasi tidak diketahui1
Karyadi KaryadiUniversitas Buana Perjuangan Karawang1
Sukarman SukarmanNational Research and Innovation Agency1
Nana RahdianaUniversitas Buana Perjuangan Karawang1
Dodi MulyadiUniversitas Buana Perjuangan Karawang1
Alizar NurdinUniversitas Buana Perjuangan Karawang1
Amri AbdulahSekolah Tinggi Teknologi Wastukancana1
Dede Ardi RajabSekolah Tinggi Teknologi Wastukancana1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.unimma.ac.id/index.php/mesi/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Tensile shear load in resistance spot welding of dissimilar metals: An optimization study using response surface methodology</dc:title>
	<dc:creator xml:lang="en">Sukarman, Sukarman</dc:creator>
	<dc:creator xml:lang="en">Triyono, Triyono</dc:creator>
	<dc:creator xml:lang="en">Kristiawan, Budi</dc:creator>
	<dc:creator xml:lang="en">Amir, Amir</dc:creator>
	<dc:creator xml:lang="en">Fazrin, Nazar</dc:creator>
	<dc:creator xml:lang="en">Suhara, Ade</dc:creator>
	<dc:creator xml:lang="en">Azizah, Renata Lintang</dc:creator>
	<dc:creator xml:lang="en">Mucharom, Fajar</dc:creator>
	<dc:subject xml:lang="en">Box-Behnken design</dc:subject>
	<dc:subject xml:lang="en">Resistance spot welding</dc:subject>
	<dc:subject xml:lang="en">Response Surface Methodology</dc:subject>
	<dc:subject xml:lang="en">Tensile shear load</dc:subject>
	<dc:description xml:lang="en">Resistance spot welding (RSW) is being applied extensively in different industries, specifically the automotive sector. Therefore, this study was conducted to optimize the tensile strength load (TSL) in RSW by investigating the application of dissimilar materials as input parameters. The optimization process involved the combination of different galvanized and non-galvanized steel materials. The production of car bodies using galvanized steel with approximately 13.0 microns thick zinc (Zn) coating was found to be a standard practice, but this zinc layer usually presents challenges due to the poor weldability. This study prepared 27 units of TSL samples using a spot-welding machine and a pressure force system (PFS) for the electrode tip. The aim was to determine the optimal TSL through the exploration of specified RSW parameters. The process focused on using the response surface methodology (RSM) to achieve the desired outcome while the Box-Behnken design was applied to determine the input parameters. The optimal TSL obtained was 5265.15 N by setting the squeeze time to 21.0 cycles at a welding current of 24.5 kA, a welding time of 0.5 s, and a holding time of 15.0 cycles. The highest TSL value recorded was 5937.94 N at 21.0 cycles, 27.0 kA, 0.6 s, and 15.0 cycles respectively. These findings were considered significant to the enhancement of productivity across industries, specifically in the RSW process. However, further study was required to investigate additional response variables such as the changes in hardness and microstructure.</dc:description>
	<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
	<dc:date>2023-09-11</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unimma.ac.id/mesi/article/view/9606</dc:identifier>
	<dc:identifier>10.31603/mesi.9606</dc:identifier>
	<dc:source xml:lang="en">Mechanical Engineering for Society and Industry; Vol. 3 No. 2 (2023); 66-77</dc:source>
	<dc:source>2798-5245</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unimma.ac.id/mesi/article/view/9606/4576</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2023 Sukarman - Sukarman, Triyono Triyono, Budi Kristiawan, Amir Amir, Nazar Fazrin, Ade Suhara, Renata Lintang Azizah, Fajar Mucharom</dc:rights>
</oai_dc:dc>