Jurnal
SINTA 1
Effect of deposition current on bead geometry characteristics of low carbon steel single wall structure fabricated by wire arc additive manufacturing
Mechanical Engineering for Society and Industry · Vol. 5 No. 2 (2025) · hlm. 510–520
ISSN 2798-5245
Terbit 2025-12-28
Penerbit Universitas Muhammadiyah Magelang
Bahasa en
Abstrak
Wire arc additive manufacturing (WAAM) is gaining popularity due to its ability to produce large metal parts quickly and efficiently. It produces less waste and has a more efficient production time than subtractive manufacturing. However, those capabilities come with unavoidable disadvantages, post-processing by machining becomes necessary to achieve the desired product dimension. Therefore, this research aimed to evaluate the bead geometry and utilization area of the WAAM-fabricated structure by varying the deposition current. The wall-structured specimens were fabricated using gas metal arc welding (GMAW) with motorized drivers for x, y, and z coordinates. The material used in this research was low carbon steel ER70S-6 filler metal with ASTM A36 low carbon steel substrate. The Varying parameter was deposition current with other related process parameters remaining constant. Material testing and characterization techniques included geometric measurement by profile projector plotted into a scattered diagram, and the cross section of the specimens were observed using a digital microscope. The experiment resulted in increased bead dimension in width and height along with increased deposition current. The largest bead dimension was achieved in 180A deposition current with average bead width and height was 6.84 mm and 1.6 mm respectively. The best deposition current was 160A, with highest area utilization of 81.43% and width uniformity.
Jaringan kolaborasi para penulis
21 penulis ·
47 tautan kepenulisan bersama
· 18 lintas organisasi
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
University of Indonesia Sekolah Tinggi Teknologi Warga Surakarta Jakarta State Polytechnic Keio University University of Sharjah Universitas Tunas Pembangunan Afiliasi tidak diketahui
Organisasi berbeda
Organisasi sama
Afiliasi tidak diketahui
Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.
Sumber metadata: OAI-PMH (metadata jurnal) https://journal.unimma.ac.id/index.php/mesi/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/ http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
<dc:title xml:lang="en">Effect of deposition current on bead geometry characteristics of low carbon steel single wall structure fabricated by wire arc additive manufacturing</dc:title>
<dc:creator xml:lang="en">Wicaksono, Danny</dc:creator>
<dc:creator xml:lang="en">Baskoro, Ario Sunar</dc:creator>
<dc:creator xml:lang="en">Guarsa, Nicholas Ego</dc:creator>
<dc:creator xml:lang="en">Kiswanto, Gandjar</dc:creator>
<dc:creator xml:lang="en">Junaidi, Syarif</dc:creator>
<dc:subject xml:lang="en">GMAW</dc:subject>
<dc:subject xml:lang="en">Area utilization</dc:subject>
<dc:subject xml:lang="en">Geometric measurement</dc:subject>
<dc:subject xml:lang="en">Heat input</dc:subject>
<dc:subject xml:lang="en">Layer dimension</dc:subject>
<dc:description xml:lang="en">Wire arc additive manufacturing (WAAM) is gaining popularity due to its ability to produce large metal parts quickly and efficiently. It produces less waste and has a more efficient production time than subtractive manufacturing. However, those capabilities come with unavoidable disadvantages, post-processing by machining becomes necessary to achieve the desired product dimension. Therefore, this research aimed to evaluate the bead geometry and utilization area of the WAAM-fabricated structure by varying the deposition current. The wall-structured specimens were fabricated using gas metal arc welding (GMAW) with motorized drivers for x, y, and z coordinates. The material used in this research was low carbon steel ER70S-6 filler metal with ASTM A36 low carbon steel substrate. The Varying parameter was deposition current with other related process parameters remaining constant. Material testing and characterization techniques included geometric measurement by profile projector plotted into a scattered diagram, and the cross section of the specimens were observed using a digital microscope. The experiment resulted in increased bead dimension in width and height along with increased deposition current. The largest bead dimension was achieved in 180A deposition current with average bead width and height was 6.84 mm and 1.6 mm respectively. The best deposition current was 160A, with highest area utilization of 81.43% and width uniformity.</dc:description>
<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
<dc:date>2025-12-28</dc:date>
<dc:type>info:eu-repo/semantics/article</dc:type>
<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
<dc:format>application/pdf</dc:format>
<dc:identifier>https://journal.unimma.ac.id/mesi/article/view/14623</dc:identifier>
<dc:identifier>10.31603/mesi.14623</dc:identifier>
<dc:source xml:lang="en">Mechanical Engineering for Society and Industry; Vol. 5 No. 2 (2025); 510-520</dc:source>
<dc:source>2798-5245</dc:source>
<dc:language>en</dc:language>
<dc:relation>https://journal.unimma.ac.id/mesi/article/view/14623/6427</dc:relation>
<dc:rights xml:lang="en">Copyright (c) 2025 Danny Wicaksono, Ario Sunar Baskoro, Nicholas ego Guarsa, Gandjar Kiswanto, Syarif Junaidi, Prof.</dc:rights>
</oai_dc:dc>
Sitasi dan pengindeksan
Jumlah menurut tiap indeks pada 13 Nov 2026; setiap indeks menghitung sitasi dengan cara berbeda.
OpenAlex juga mencatat karya ini di: crossref.
Sitasi artikel ini
APA 7
Wicaksono, D., Baskoro, A. S., Guarsa, N. E., Kiswanto, G., & Junaidi, S. (2025). Effect of deposition current on bead geometry characteristics of low carbon steel single wall structure fabricated by wire arc additive manufacturing. Mechanical Engineering for Society and Industry, 5(2), 510–520. https://doi.org/10.31603/mesi.14623
Salin
IEEE
D. Wicaksono, A. S. Baskoro, N. E. Guarsa, G. Kiswanto, and S. Junaidi, “Effect of deposition current on bead geometry characteristics of low carbon steel single wall structure fabricated by wire arc additive manufacturing,” Mechanical Engineering for Society and Industry, vol. 5, no. 2, pp. 510–520, 2025, doi: 10.31603/mesi.14623.
Salin
Dibuat dari metadata jurnal; periksa nama penulis sebelum dipakai.