Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

The influence of coffee ground waste on the thermal and mechanical characteristics of polymer-based 3D printing filament materials

Mechanical Engineering for Society and Industry · Vol. 6 No. 1 (2026) · hlm. 230–239

DOI
10.31603/mesi.14897
ISSN
2798-5245
Terbit
2026-05-24
Penerbit
Universitas Muhammadiyah Magelang
Bahasa
en
Lisensi
creativecommons.org/licenses/by-nc/4.0

Abstrak

The development of polymer-based 3D printing filaments is challenged by the need for greater mechanical strength and thermal stability. Coffee grounds waste was selected as a filler to enhance the properties of polylactic acid (PLA), a widely used polymer filament. The coffee grounds were treated with NaOH to remove lignin, hemicellulose, and impurities, thereby improving their compatibility with the PLA matrix. The treated filler was incorporated into the polymer matrix at 2%- 8% w/w and molded into standard tensile test specimens according to ASTM D638. Mechanical testing and thermal analysis were performed to assess the performance of the resulting biocomposites. Results indicate that increasing the filler content in 2% w/w increments up to 8% w/w enhances tensile strength by approximately 1.5 MPa, tensile strain by 0.002, and elastic modulus by 30.378 MPa. Thermal analysis also shows an increase in glass transition temperature (Tg) from 59°C to 66°C and a rise in degradation peak temperature from 335.9°C to 371.1°C. These enhancements are attributed to improved interfacial adhesion between the treated filler and the PLA matrix, which restricts polymer chain mobility. Alkali-treated coffee grounds waste thus represents a promising sustainable filler for enhancing the mechanical and thermal performance of polymer-based 3D printing filaments.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 166 tautan kepenulisan bersama · 116 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Trisakti
  • Diponegoro University
  • State University of Jakarta
  • State University of Semarang
  • Islamic University of Indonesia
  • Universiti Malaysia Pahang Al-Sultan Abdullah
  • National Research and Innovation Agency
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Deni Fajar FitriyanaState University of Semarang9
Tezara CionitaINTI International University7
Al Ichlas ImranUniversitas Halu Oleo4
Rifky IsmailDiponegoro University3
Jamiluddin JaafarTun Hussein Onn University of Malaysia3
Samsudin AnisState University of Semarang2
Athanasius Priharyoto BayusenoDiponegoro University2
Agustinus Purna IrawanTarumanagara University2
Rozanna DewiMalikussaleh University2
M. R. M. RejabUniversiti Malaysia Pahang Al-Sultan Abdullah2
Agung Efriyo HadiUniversitas Malahayati2
Muji SetiyoUniversitas Muhammadiyah Magelang2
Joni FatUniversitas Trisakti1
Parwadi MoenginUniversitas Trisakti1
Pudji AstutiUniversitas Trisakti1
Agus PrasetyoDiponegoro University1
Risky IsmailAfiliasi tidak diketahui1
Muhammad AfrizalDiponegoro University1
Janviter ManaluCenderawasih University1
Achmad Erlangga Bintang SamodraAfiliasi tidak diketahui1
Gunawan RefiadiUniversitas Sebelas April1
Iis Siti AisyahUniversitas Muhammadiyah Malang1
Sri NugrohoDiponegoro University1
Thesar Aditya NurcholisDiponegoro University1
Riyadi RiyadiState University of Jakarta1
Ari SetiawanAfiliasi tidak diketahui1
Ahmad Yusuf KholilState University of Jakarta1
Siska Titik DwiyatiState University of Jakarta1
Danang Budi PratamaState University of Jakarta1
Eko Arif SyaefudinState University of Jakarta1
Rahmadi YotenkaIslamic University of Indonesia1
Rahmat Doni WidodoState University of Semarang1
Muhammad KhafidhIslamic University of Indonesia1
Finny Pratama PuteraIslamic University of Indonesia1
Nur Hidayah IsmailUniversiti Teknikal Malaysia Melaka1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.unimma.ac.id/index.php/mesi/oai, pertama di-harvest 9 Nov 2026, terakhir terlihat 9 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">The influence of coffee ground waste on the thermal and mechanical characteristics of polymer-based 3D printing filament materials</dc:title>
	<dc:creator xml:lang="en">Cahyati, Sally</dc:creator>
	<dc:creator xml:lang="en">Krusdianto, Rudi</dc:creator>
	<dc:creator xml:lang="en">Aji, Daisman Purnomo Bayyu</dc:creator>
	<dc:creator xml:lang="en">Siregar, Januar Parlaungan</dc:creator>
	<dc:creator xml:lang="en">Laskmono, Joddy Arya</dc:creator>
	<dc:subject xml:lang="en">Coffee</dc:subject>
	<dc:subject xml:lang="en">Alkalized</dc:subject>
	<dc:subject xml:lang="en">Waste</dc:subject>
	<dc:subject xml:lang="en">Filament</dc:subject>
	<dc:subject xml:lang="en">3D printing</dc:subject>
	<dc:description xml:lang="en">The development of polymer-based 3D printing filaments is challenged by the need for greater mechanical strength and thermal stability. Coffee grounds waste was selected as a filler to enhance the properties of polylactic acid (PLA), a widely used polymer filament. The coffee grounds were treated with NaOH to remove lignin, hemicellulose, and impurities, thereby improving their compatibility with the PLA matrix. The treated filler was incorporated into the polymer matrix at 2%- 8% w/w and molded into standard tensile test specimens according to ASTM D638. Mechanical testing and thermal analysis were performed to assess the performance of the resulting biocomposites. Results indicate that increasing the filler content in 2% w/w increments up to 8% w/w enhances tensile strength by approximately 1.5 MPa, tensile strain by 0.002, and elastic modulus by 30.378 MPa. Thermal analysis also shows an increase in glass transition temperature (Tg) from 59°C to 66°C and a rise in degradation peak temperature from 335.9°C to 371.1°C. These enhancements are attributed to improved interfacial adhesion between the treated filler and the PLA matrix, which restricts polymer chain mobility. Alkali-treated coffee grounds waste thus represents a promising sustainable filler for enhancing the mechanical and thermal performance of polymer-based 3D printing filaments.</dc:description>
	<dc:publisher xml:lang="en">Universitas Muhammadiyah Magelang</dc:publisher>
	<dc:date>2026-05-24</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unimma.ac.id/mesi/article/view/14897</dc:identifier>
	<dc:identifier>10.31603/mesi.14897</dc:identifier>
	<dc:source xml:lang="en">Mechanical Engineering for Society and Industry; Vol. 6 No. 1 (2026); 230-239</dc:source>
	<dc:source>2798-5245</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unimma.ac.id/mesi/article/view/14897/6821</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2026 Sally Cahyati, Rudi Krusdianto, Daisman Purnomo Bayyu Aji, Januar Parlaungan Siregar, Joddy Arya Laskmono</dc:rights>
	<dc:rights xml:lang="en">http://creativecommons.org/licenses/by-nc/4.0</dc:rights>
</oai_dc:dc>