Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

THE INFLUENCE OF MOLYBDENUM DISULPHIDE-FRICTION MODIFIER (FM) ADDITIVE INCREMENT ON THE FRICTION AND WEAR PREVENTION BEHAVIOUR OF HVI 60 BASE OIL

Scientific Contributions Oil and Gas · Vol. 38 No. 2 (2015) · hlm. 71–82

DOI
10.29017/SCOG.38.2.542
ISSN
2541-0520, 2089-3361
Terbit
2015-08-31
Penerbit
Testing Center for Oil and Gas LEMIGAS
Bahasa
eng
Lisensi
creativecommons.org/licenses/by/4.0

Abstrak

Friction will always be found in a mechanical system. It is therefore necessary to minimize friction, so it becomes a more effi cient use of energy. This paper discusses the infl uence of MoS2 friction modifier (FM) additive in the form of powder with two different mesh sizes, i.e. 90 nm and 1.5 um, on the friction and wear characteristic of HVI 60 base oil. The variation of MoS2 were 0,05%; 0,1%; 0,5% weight whereas MoS2 1.5 um were 0,05%; 0,1%; 0,5%; 1% and 2% weight. MoS2 additive 90 nm was mixed with base oil and stirred with magnetic stirrer for 60 minutes at 50oC and homogenized in an ultrasonic homogenizer for 1 hour. For the MoS2 1.5 um, the additive was mixed with base oil and stirred with magnetic stirrer for 60 minutes at 75oC without using an ultrasonic homogenizer. Friction and wear characteristics of these mixtures were tested using four-ball and SRV test-rig. The wear scars were analyzed by using a scanning electron microscope (SEM). The results of the tests showed that the addition of 0.1% weight MoS2 additive, both in 90 nm and 1.5 um, resulted in an optimum increase in friction and wear characteristic of 23% and 11%, respectively. Observation on the wear scar showed that adhesive and abrasive wear mechanisms were involved in the wear process. The results of this research could be applied in the production of lubricating oils that can improve engine performance. Keywords: additive, friction, wear, molybdenum disulfi de, four-ball

Kata kunci

Jaringan kolaborasi para penulis

11 penulis · 23 tautan kepenulisan bersama · 8 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • University of Indonesia
  • Kementerian Energi dan Sumber Daya Mineral
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Setyo WidodoAfiliasi tidak diketahui2
Rona Malam KarinaAfiliasi tidak diketahui2
Muhammad Faja TaufiqurrahmanUniversity of Indonesia1
Tri Aji SetyawanUniversity of Indonesia1
Riesta AnggaraniKementerian Energi dan Sumber Daya Mineral1
Cahyo Setyo WibowoKementerian Energi dan Sumber Daya Mineral1
Bambang SugiartoUniversity of Indonesia1
Milda FibreAfiliasi tidak diketahui1
Setyo Ari WibowoAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.lemigas.esdm.go.id/index.php/SCOG/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 10 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">THE INFLUENCE OF MOLYBDENUM DISULPHIDE-FRICTION MODIFIER (FM) ADDITIVE INCREMENT ON THE FRICTION AND WEAR PREVENTION BEHAVIOUR OF HVI 60 BASE OIL</dc:title>
	<dc:creator xml:lang="en">Hanifuddin, Muhammad</dc:creator>
	<dc:creator xml:lang="en">Sofyan, Nofrijon</dc:creator>
	<dc:subject xml:lang="en">additive</dc:subject>
	<dc:subject xml:lang="en">friction</dc:subject>
	<dc:subject xml:lang="en">wear</dc:subject>
	<dc:subject xml:lang="en">molybdenum disulfi de</dc:subject>
	<dc:subject xml:lang="en">four-ball</dc:subject>
	<dc:description xml:lang="en">Friction will always be found in a mechanical system. It is therefore necessary to minimize friction, so it becomes a more effi cient use of energy. This paper discusses the infl uence of MoS2 friction modifier (FM) additive in the form of powder with two different mesh sizes, i.e. 90 nm and 1.5 um, on the friction and wear characteristic of HVI 60 base oil. The variation of MoS2 were 0,05%; 0,1%; 0,5% weight whereas MoS2 1.5 um were 0,05%; 0,1%; 0,5%; 1% and 2% weight. MoS2 additive 90 nm was mixed with base oil and stirred with magnetic stirrer for 60 minutes at 50oC and homogenized in an ultrasonic homogenizer for 1 hour. For the MoS2 1.5 um, the additive was mixed with base oil and stirred with magnetic stirrer for 60 minutes at 75oC without using an ultrasonic homogenizer. Friction and wear characteristics of these mixtures were tested using four-ball and SRV test-rig. The wear scars were analyzed by using a scanning electron microscope (SEM). The results of the tests showed that the addition of 0.1% weight MoS2 additive, both in 90 nm and 1.5 um, resulted in an optimum increase in friction and wear characteristic of 23% and 11%, respectively. Observation on the wear scar showed that adhesive and abrasive wear mechanisms were involved in the wear process. The results of this research could be applied in the production of lubricating oils that can improve engine performance. Keywords: additive, friction, wear, molybdenum disulfi de, four-ball</dc:description>
	<dc:publisher xml:lang="en">Testing Center for Oil and Gas LEMIGAS</dc:publisher>
	<dc:date>2015-08-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.lemigas.esdm.go.id/index.php/SCOG/article/view/542</dc:identifier>
	<dc:identifier>10.29017/SCOG.38.2.542</dc:identifier>
	<dc:source xml:lang="en">Scientific Contributions Oil and Gas; Vol. 38 No. 2 (2015); 71-82</dc:source>
	<dc:source xml:lang="id">Scientific Contributions Oil and Gas; Vol 38 No 2 (2015); 71-82</dc:source>
	<dc:source>2541-0520</dc:source>
	<dc:source>2089-3361</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://journal.lemigas.esdm.go.id/index.php/SCOG/article/view/542/308</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2015 SCIENTIFIC CONTRIBUTIONS OIL AND GAS (SCOG)</dc:rights>
	<dc:rights xml:lang="en">https://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>