Melola Discovery

← Melola Discovery

Jurnal SINTA 1

STUDY OF MAKING POLYESTER RESIN MATRIX COMPOSITES USING BASALT SCORIA POWDER FILLERS TO TENSILE STRENGTH AND COMPRESSIVE STRENGTH

Sinergi · Vol. 25 No. 3 (2021) · hlm. 299–308

DOI
10.22441/sinergi.2021.3.007
ISSN
2460-1217, 1410-2331
Terbit
2021-08-25
Penerbit
Universitas Mercu Buana
Bahasa
eng

Abstrak

An experimental study on the manufacture of polyester resin matrix composites using basalt powder as a reinforcing filler has been carried out. Basalt is a volcanic igneous rock often found in East Lampung and has not been utilised. Basalt is chosen as a reinforcing filler because basalt has advantages such as wear resistance, corrosion resistance, resistance to chemical reactions, and high hardness. The research parameters used were variations in the size of the basalt powder, the composition of the polyester resin matrix to the basalt powder, and the percentage of the catalyst. All parameters were mixed according to the research procedure, and all samples were formed under pressure 20 kN. Tensile test results showed the highest value of 0.961 kgf/mm2 from 60 mesh-25% polyester-1/30 catalyst variation parameter. The highest compressive strength value of 28.331 kgf/mm2 was obtained from the various parameters of 270 mesh-20% polyester-1/20 catalyst and 270 mesh-25% polyester-1/30 catalyst. The results were not much different from those, which is 27.787 kgf/mm2. The use of 1/30 hardener catalyst to the amount of polymer by 25 %wt gives optimal results on the characterisation material testing. However, the effect of the filler grain size gave different results for each test carried out. Therefore, to obtain the desired mechanical properties when using basalt rock powder as a filler, it is necessary to pay attention to the correct grain size.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 209 tautan kepenulisan bersama · 142 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • National Research and Innovation Agency
  • Sriwijaya University
  • Indonesian Institute of Sciences
  • Institut Teknologi Sepuluh Nopember
  • Institut Teknologi Kalimantan
  • Universitas Jambi
  • State University of Jakarta
  • Organisasi lain
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Tumpal Ojahan RajagukgukUniversitas Malahayati5
Hasanudin HasanudinSriwijaya University4
Lenny MarlindaUniversitas Jambi4
Roni MaryanaIndonesian Institute of Sciences3
Wan Ryan AsriSriwijaya University3
Nino RinaldiNational Research and Innovation Agency3
Novia NoviaSriwijaya University3
Indri YatiNational Research and Innovation Agency3
Maja Pranata MarbunAfiliasi tidak diketahui3
Achmad RoesyadiInstitut Teknologi Sepuluh Nopember3
Danawati Hari PrajitnoInstitut Teknologi Sepuluh Nopember3
Fahma RiyantiSriwijaya University2
Fitri HadiahSriwijaya University2
Peri OktiarmiUniversitas Jambi2
Sugeng PriyantoState University of Jakarta2
Abdul AzizInstitut Teknologi Sepuluh Nopember2
Sudibyo SudibyoNational Research and Innovation Agency2
Rahmawati RahmawatiSamudra University1
Erik Budi SantikoNational Research and Innovation Agency1
Sarah Nur FauziahUniversitas Muhammadiyah Jakarta1
Yustinah YustinahUniversitas Muhammadiyah Jakarta1
S. SudibyoNational Research and Innovation Agency1
Sugeng PriyantoState University of Jakarta1
Tri MaryaniUniversitas Semarang1
Triastuti SulistyaningsihState University of Semarang1
Andreas SibueaLampung University1
Wasinton SimanjuntakLampung University1
Fuad SyafaatInstitut Teknologi Kalimantan1
Havier Samuel Huttur Silalahi RajaInstitut Teknologi Kalimantan1
Riza AlvianyInstitut Teknologi Kalimantan1
Erik PrasetyoIndonesian Institute of Sciences1
Mhika NakashimaSriwijaya University1
Firman KurniawansyahInstitut Teknologi Sepuluh Nopember1
Dibyo PranowoNational Research and Innovation Agency1
Asif AunillahNational Research and Innovation Agency1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://publikasi.mercubuana.ac.id/index.php/sinergi/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 10 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">STUDY OF MAKING POLYESTER RESIN MATRIX COMPOSITES USING BASALT SCORIA POWDER FILLERS TO TENSILE STRENGTH AND COMPRESSIVE STRENGTH</dc:title>
	<dc:creator>Birawidha, David Candra</dc:creator>
	<dc:creator>Isnugroho, Kusno</dc:creator>
	<dc:creator>Hendronursito, Yusup</dc:creator>
	<dc:creator>Amin, Muhammad</dc:creator>
	<dc:creator>Al Muttaqii, Muhammad</dc:creator>
	<dc:subject xml:lang="en-US">Basalt</dc:subject>
	<dc:subject xml:lang="en-US">Composites</dc:subject>
	<dc:subject xml:lang="en-US">Compressive strength</dc:subject>
	<dc:subject xml:lang="en-US">Resin polyester</dc:subject>
	<dc:subject xml:lang="en-US">Tensile strength</dc:subject>
	<dc:description xml:lang="en-US">An experimental study on the manufacture of polyester resin matrix composites using basalt powder as a reinforcing filler has been carried out. Basalt is a volcanic igneous rock often found in East Lampung and has not been utilised. Basalt is chosen as a reinforcing filler because basalt has advantages such as wear resistance, corrosion resistance, resistance to chemical reactions, and high hardness. The research parameters used were variations in the size of the basalt powder, the composition of the polyester resin matrix to the basalt powder, and the percentage of the catalyst. All parameters were mixed according to the research procedure, and all samples were formed under pressure 20 kN. Tensile test results showed the highest value of 0.961 kgf/mm2 from 60 mesh-25% polyester-1/30 catalyst variation parameter. The highest compressive strength value of 28.331 kgf/mm2 was obtained from the various parameters of 270 mesh-20% polyester-1/20 catalyst and 270 mesh-25% polyester-1/30 catalyst. The results were not much different from those, which is 27.787 kgf/mm2. The use of 1/30 hardener catalyst to the amount of polymer by 25 %wt gives optimal results on the characterisation material testing. However, the effect of the filler grain size gave different results for each test carried out. Therefore, to obtain the desired mechanical properties when using basalt rock powder as a filler, it is necessary to pay attention to the correct grain size.</dc:description>
	<dc:publisher xml:lang="en-US">Universitas Mercu Buana</dc:publisher>
	<dc:date>2021-08-25</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:format>application/msword</dc:format>
	<dc:identifier>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/9973</dc:identifier>
	<dc:identifier>10.22441/sinergi.2021.3.007</dc:identifier>
	<dc:source xml:lang="en-US">SINERGI; Vol. 25 No. 3 (2021); 299-308</dc:source>
	<dc:source>2460-1217</dc:source>
	<dc:source>1410-2331</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/9973/4810</dc:relation>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/9973/10955</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2021 SINERGI</dc:rights>
</oai_dc:dc>