Jurnal SINTA 1
Finite Element Analysis (FEA) of blade weed design using Ansys workbench
Sinergi · Vol. 26 No. 3 (2022) · hlm. 371–378
- ISSN
- 2460-1217, 1410-2331
- Terbit
- 2022-10-14
- Penerbit
- Universitas Mercu Buana
- Bahasa
- eng
Abstrak
Manual, semi-conventional, and conventional weed eradication are the three forms of weed eradication utilized. Farmers benefit greatly from the usage of weeding equipment in combating pests in the fields. The blade you use determines how successful you are at weeding. As a result, it is required to examine the weeding weeds blade. With a tetrahedral mesh, simulation utilizing the finite element analysis approach allows for the optimization of design, computation, and prediction of material strength. The goal of this research was to figure out how much von Mises's stress, deformation, and safety factor were worth. ANSYS Workbench software was used to simulate various loadings of 10N, 25N, and 50N. The highest von Mises stress created by simulation of modelling weed blades at 10N, 25N, and 50N loads is around 2.95x10-2 MPa, 7.38x10-2 MPa, and 0.14755 MPa, respectively. Each of the safety factors is 15, and the maximum deformation value is 4.26x10-7mm; 1.06x10-6mm; 2.13x10-6mm. The safety factor indicates that the weed weeding knife design is safe to use up to 50N loading.
Kata kunci
Jaringan kolaborasi para penulis
39 penulis · 120 tautan kepenulisan bersama · 78 lintas organisasi
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
- Sumatera Institute of Technology
- Institut Teknologi Nasional Yogyakarta
- Universitas Tidar
- Universitas AKPRIND Indonesia
- Universitas Prof. Dr. Hazairin SH.
- Politeknik Negeri Banjarmasin
- Politeknik ATI Makassar
- Organisasi lain
- Afiliasi tidak diketahui
- Organisasi berbeda
- Organisasi sama
- Afiliasi tidak diketahui
- Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
| Rekan penulis | Organisasi | Artikel bersama |
|---|---|---|
| Akhmad Nurdin | Universitas Tidar | 2 |
| Rofiqul Umam | Kwansei Gakuin University | 2 |
| Tohirin | Afiliasi tidak diketahui | 1 |
| Andy Erwin Wijaya | Afiliasi tidak diketahui | 1 |
| Nofry Hence Tarumasely | Institut Teknologi Nasional Yogyakarta | 1 |
| Novandri Kusuma Wardana | Institut Teknologi Nasional Yogyakarta | 1 |
| Fajri Kurniawan | University of Technology Malaysia | 1 |
| Fajar Paundra | Sumatera Institute of Technology | 1 |
| Abdul Muhyi | Sumatera Institute of Technology | 1 |
| Dzikrina Salsabila Yasmin | Sumatera Institute of Technology | 1 |
| Iqbal Zulfikar Alief Utama | Universitas Tidar | 1 |
| Rosyidi Hidayat | Afiliasi tidak diketahui | 1 |
| Iqbal Zulfikar | Afiliasi tidak diketahui | 1 |
| Bambang Irawan | Politeknik Negeri Malang | 1 |
| Sofiana Herman | Sumatera Institute of Technology | 1 |
| Vico Luthfi Ipmawan | Sumatera Institute of Technology | 1 |
| Mochamad Iqbal | Sumatera Institute of Technology | 1 |
| Ikah Ning Prasetiowati Permanasari | Sumatera Institute of Technology | 1 |
| Zidan Yusron Wijanarko | Universitas Tidar | 1 |
| Obrin Trianda | Institut Teknologi Nasional Yogyakarta | 1 |
| Hurien Helmi | Institut Teknologi Nasional Yogyakarta | 1 |
| Hasan Said Tortop | İstanbul Esenyurt Üniversitesi | 1 |
| Andika Eko Prasetiyo | The University of Melbourne | 1 |
| Syamsul Huda | UIN Syekh Wasil Kediri | 1 |
| Kittisak Jermsittiparsert | Chulalongkorn University | 1 |
| Muhamad Syazali | Universitas Islam Negeri Raden Intan Lampung | 1 |
| Sely Novita Sari | Institut Teknologi Nasional Yogyakarta | 1 |
| Rahmad Junaidi | UIN Sunan Ampel Surabaya | 1 |
| Amir Machmud | National Central University | 1 |
| Alva Edy Tontowi | Universitas Gadjah Mada | 1 |
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.