Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Hardness and microstructure of FDM 3D printed parts using self-made PLA-brass filaments

Sinergi · Vol. 28 No. 3 (2024) · hlm. 433–450

DOI
10.22441/sinergi.2024.3.001
ISSN
2460-1217, 1410-2331
Terbit
2024-07-08
Penerbit
Universitas Mercu Buana
Bahasa
eng

Abstrak

Technological advancements in the industrial sector have led to rapid developments in 3D printing technology, enabling the creation of three-dimensional prototype models. Various filaments, including polyethylene terephthalate glycol, nylon, and polylactic acid, have been widely adopted in the industry. However, filaments composed of metal mixtures are relatively scarce in Indonesia, primarily available only through select online shops worldwide. The production and sale of such filaments present lucrative opportunities within the manufacturing industry. In this research, an experimental study was conducted to examine the hardness of test specimens fabricated using PLA-brass filament. The objective was to identify the optimal hardness value of the specimens. The study focused on three key parameters: nozzle temperature, layer height, and print speed, each at two different levels. The Taguchi L4(2³) experimental design was employed, along with S/N ratio and ANOVA analysis, to evaluate the results. The findings revealed that specific combinations of parameters yield favorable hardness values, as determined by the Taguchi Method. The optimal set of parameters for achieving good hardness values was determined to be a nozzle temperature of 230°C, a layer height of 0.2 mm, and a print speed of 40 mm/s. These results enhance the understanding of PLA-brass filament properties and facilitate the utilization of 3D printing technology in the manufacturing industry.

Kata kunci

Jaringan kolaborasi para penulis

21 penulis · 57 tautan kepenulisan bersama · 14 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Jember
  • Papua New Guinea University of Technology
  • Sriwijaya University
  • Bandung Institute of Technology
  • Universitas Halu Oleo
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Mochamad AsrofiUniversitas Jember2
Laily Ilman WiduriSriwijaya University1
Tri HandoyoAfiliasi tidak diketahui1
Wardatul JannahBandung Institute of Technology1
Danang YudistiroUniversitas Jember1
Ahmad Rendi MaulanaUniversitas Jember1
Boy Arief FachriUniversitas Jember1
Mochamad Edoward RamadhanUniversitas Jember1
Renald Rochman MauludyUniversitas Jember1
Intan HardiatamaUniversitas Jember1
Doddy ParningotanAfiliasi tidak diketahui1
Muhammad YusufUniversitas Halu Oleo1
Salahuddin JunusUniversitas Jember1
Revvan Rifada PradizaUniversitas Jember1
Gaguk JatisukamtoAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://publikasi.mercubuana.ac.id/index.php/sinergi/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Hardness and microstructure of FDM 3D printed parts using self-made PLA-brass filaments</dc:title>
	<dc:creator>Darsin, Mahros</dc:creator>
	<dc:creator>Ramadhan, Ivan Fadilla</dc:creator>
	<dc:creator>Sumarji, Sumarji</dc:creator>
	<dc:creator>Dwilaksana, Dedi</dc:creator>
	<dc:creator>Sutjahjono, Hary</dc:creator>
	<dc:creator>Ales, Steve Korakan</dc:creator>
	<dc:subject xml:lang="en-US">3D Printing</dc:subject>
	<dc:subject xml:lang="en-US">Hardness</dc:subject>
	<dc:subject xml:lang="en-US">PLA-brass</dc:subject>
	<dc:description xml:lang="en-US">Technological advancements in the industrial sector have led to rapid developments in 3D printing technology, enabling the creation of three-dimensional prototype models. Various filaments, including polyethylene terephthalate glycol, nylon, and polylactic acid, have been widely adopted in the industry. However, filaments composed of metal mixtures are relatively scarce in Indonesia, primarily available only through select online shops worldwide. The production and sale of such filaments present lucrative opportunities within the manufacturing industry. In this research, an experimental study was conducted to examine the hardness of test specimens fabricated using PLA-brass filament. The objective was to identify the optimal hardness value of the specimens. The study focused on three key parameters: nozzle temperature, layer height, and print speed, each at two different levels. The Taguchi L4(2³) experimental design was employed, along with S/N ratio and ANOVA analysis, to evaluate the results. The findings revealed that specific combinations of parameters yield favorable hardness values, as determined by the Taguchi Method. The optimal set of parameters for achieving good hardness values was determined to be a nozzle temperature of 230°C, a layer height of 0.2 mm, and a print speed of 40 mm/s. These results enhance the understanding of PLA-brass filament properties and facilitate the utilization of 3D printing technology in the manufacturing industry. </dc:description>
	<dc:publisher xml:lang="en-US">Universitas Mercu Buana</dc:publisher>
	<dc:date>2024-07-08</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/21863</dc:identifier>
	<dc:identifier>10.22441/sinergi.2024.3.001</dc:identifier>
	<dc:source xml:lang="en-US">SINERGI; Vol. 28 No. 3 (2024); 433-450</dc:source>
	<dc:source>2460-1217</dc:source>
	<dc:source>1410-2331</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/21863/8736</dc:relation>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/21863/11681</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2024 SINERGI</dc:rights>
</oai_dc:dc>