Melola Discovery

← Melola Discovery

Jurnal SINTA 1

The influence of Silane Coupling Agent and porogen ratio on 3D scaffold PCL/HA

Sinergi · Vol. 29 No. 3 (2025) · hlm. 747–754

DOI
10.22441/sinergi.2025.3.016
ISSN
2460-1217, 1410-2331
Terbit
2025-09-04
Penerbit
Universitas Mercu Buana
Bahasa
eng

Abstrak

The design of scaffold based on polycaprolactone (PCL) and hydroxyapatite (HA) has attracted attention as a solution for bone tissue regeneration. However, the main challenge in its development is the difficulty in achieving an optimal balance between porosity and mechanical strength. Suboptimal porosity limits the scaffold ability to support cell proliferation, and weak mechanical properties result in the scaffold being less than optimal as a load-bearing implant material during the bone cell regeneration process. This study aims to address these issues by evaluating the effects of the silane coupling agent 3-aminopropyltriethoxysilane (APTES) and the porogen ratio (NaCl) on the mechanical properties, morphology, and biodegradation of PCL-HA-based 3D scaffold. The scaffold were synthesized using the solvent casting/particulate leaching (SCPL) method with varying APTES concentrations (1%, 3%, and 5%) and porogen ratios. (4:1, 6:1, and 8:1). The results of characterization show that the addition of 1% APTES increases compressive strength by 283% and tensile strength by 138% compared to scaffold without APTES. A higher porogen ratio (8:1) results in the highest porosity of 78.16%, but reduces mechanical strength by 84%. The optimal combination was found in scaffold with 1% APTES and a porogen ratio of 4:1, which have optimal mechanical strength, porosity of 69.65%, and a biodegradation time of up to 380 days. This research offers a comprehensive solution to enhance the properties of PCL-HA based 3D scaffold, making a significant contribution to the development of materials for bone tissue engineering applications.

Kata kunci

Jaringan kolaborasi para penulis

11 penulis · 22 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Institut Teknologi Sepuluh Nopember
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Endah R.M. PutriInstitut Teknologi Sepuluh Nopember1
Tri WahonoInstitut Teknologi Sepuluh Nopember1
Imam MukhlashInstitut Teknologi Sepuluh Nopember1
Wikan JatimurtiInstitut Teknologi Sepuluh Nopember1
Azzahwa Fariha PadmavatiInstitut Teknologi Sepuluh Nopember1
SulistijonoInstitut Teknologi Sepuluh Nopember1
Alvian Toto WibisonoInstitut Teknologi Sepuluh Nopember1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://publikasi.mercubuana.ac.id/index.php/sinergi/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">The influence of Silane Coupling Agent and porogen ratio on 3D scaffold PCL/HA</dc:title>
	<dc:creator>Faqih, Mu'adz Abdullah</dc:creator>
	<dc:creator>Purniawan, Agung</dc:creator>
	<dc:creator>Rasyida, Amaliya</dc:creator>
	<dc:creator>Susanti, Diah</dc:creator>
	<dc:subject xml:lang="en-US">3D Scaffold</dc:subject>
	<dc:subject xml:lang="en-US">Coupling Agent</dc:subject>
	<dc:subject xml:lang="en-US">Hiydroxyapatite</dc:subject>
	<dc:subject xml:lang="en-US">PCL</dc:subject>
	<dc:subject xml:lang="en-US">Porogen Ratio</dc:subject>
	<dc:description xml:lang="en-US">The design of scaffold based on polycaprolactone (PCL) and hydroxyapatite (HA) has attracted attention as a solution for bone tissue regeneration. However, the main challenge in its development is the difficulty in achieving an optimal balance between porosity and mechanical strength. Suboptimal porosity limits the scaffold ability to support cell proliferation, and weak mechanical properties result in the scaffold being less than optimal as a load-bearing implant material during the bone cell regeneration process. This study aims to address these issues by evaluating the effects of the silane coupling agent 3-aminopropyltriethoxysilane (APTES) and the porogen ratio (NaCl) on the mechanical properties, morphology, and biodegradation of PCL-HA-based 3D scaffold. The scaffold were synthesized using the solvent casting/particulate leaching (SCPL) method with varying APTES concentrations (1%, 3%, and 5%) and porogen ratios. (4:1, 6:1, and 8:1). The results of characterization show that the addition of 1% APTES increases compressive strength by 283% and tensile strength by 138% compared to scaffold without APTES. A higher porogen ratio (8:1) results in the highest porosity of 78.16%, but reduces mechanical strength by 84%. The optimal combination was found in scaffold with 1% APTES and a porogen ratio of 4:1, which have optimal mechanical strength, porosity of 69.65%, and a biodegradation time of up to 380 days. This research offers a comprehensive solution to enhance the properties of PCL-HA based 3D scaffold, making a significant contribution to the development of materials for bone tissue engineering applications. </dc:description>
	<dc:publisher xml:lang="en-US">Universitas Mercu Buana</dc:publisher>
	<dc:date>2025-09-04</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:format>application/vnd.openxmlformats-officedocument.wordprocessingml.document</dc:format>
	<dc:format>application/vnd.openxmlformats-officedocument.wordprocessingml.document</dc:format>
	<dc:identifier>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/31119</dc:identifier>
	<dc:identifier>10.22441/sinergi.2025.3.016</dc:identifier>
	<dc:source xml:lang="en-US">SINERGI; Vol. 29 No. 3 (2025); 747-754</dc:source>
	<dc:source>2460-1217</dc:source>
	<dc:source>1410-2331</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/31119/10054</dc:relation>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/31119/12227</dc:relation>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/31119/12228</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025 SINERGI</dc:rights>
</oai_dc:dc>