Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Influence of water and oil quenching on the microstructure and mechanical properties of S45C steel

Sinergi · Vol. 30 No. 2 (2026) · hlm. 337–346

DOI
10.22441/sinergi.2026.2.002
ISSN
2460-1217, 1410-2331
Terbit
2026-06-02
Penerbit
Universitas Mercu Buana
Bahasa
eng
Lisensi
creativecommons.org/licenses/by-sa/4.0

Abstrak

S45C steel, commonly used in industrial applications due to its balanced mechanical properties, often requires further heat treatment to meet specific functional requirements. However, selecting the appropriate quenching medium, such as water or oil, significantly affects the steel's microstructural and mechanical outcomes, creating a trade-off between hardness and strength. This study systematically investigates the influence of water and oil quenching on the microstructure, hardness, and tensile properties of S45C steel. Specimens were austenitized at 900°C, held for 45 minutes, and rapidly quenched in either water or oil. Mechanical tests included hardness measurement using the Rockwell C (HRC) scale, ultimate tensile load, and ultimate tensile strength testing conducted on a universal testing machine. The Hall-Petch theory was applied to analyze the relationship between grain size and hardness. Results demonstrate significant improvements in mechanical properties with both quenching methods. Water quenching achieved the maximum hardness (55.7 HRC) compared to untreated steel (25.6 HRC), representing a 118% enhancement, with an ultimate tensile strength of 891.4 MPa versus 632.3 MPa for the baseline (41% improvement). Oil quenching demonstrated a moderate increase in hardness to 42.9 HRC (68% enhancement) while achieving a superior ultimate tensile strength of 1041.3 MPa (65% improvement). These findings establish critical trade-offs in quenching media selection: water quenching maximizes hardness for wear-resistant applications, while oil quenching optimizes tensile strength for structural components requiring superior load-bearing capacity.

Kata kunci

Jaringan kolaborasi para penulis

9 penulis · 20 tautan kepenulisan bersama · 3 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Mercu Buana University
  • Universiti of Malaysia Sabah
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Sofjan IskandarAfiliasi tidak diketahui1
Rufika MardalestariAfiliasi tidak diketahui1
Resmi HernawatiAfiliasi tidak diketahui1
Endang WahyuAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://publikasi.mercubuana.ac.id/index.php/sinergi/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Influence of water and oil quenching on the microstructure and mechanical properties of S45C steel</dc:title>
	<dc:creator>Mardiah, Enok</dc:creator>
	<dc:creator>Suharmadi, Suharmadi</dc:creator>
	<dc:creator>Fazliatul Adnan, Farrah Anis</dc:creator>
	<dc:creator>Rhyee, Jong Soo</dc:creator>
	<dc:creator>Ginting, Dianta</dc:creator>
	<dc:subject xml:lang="en-US">Grain structures</dc:subject>
	<dc:subject xml:lang="en-US">Hardness</dc:subject>
	<dc:subject xml:lang="en-US">Oil</dc:subject>
	<dc:subject xml:lang="en-US">S45C steel</dc:subject>
	<dc:subject xml:lang="en-US">Water</dc:subject>
	<dc:description xml:lang="en-US">S45C steel, commonly used in industrial applications due to its balanced mechanical properties, often requires further heat treatment to meet specific functional requirements. However, selecting the appropriate quenching medium, such as water or oil, significantly affects the steel's microstructural and mechanical outcomes, creating a trade-off between hardness and strength. This study systematically investigates the influence of water and oil quenching on the microstructure, hardness, and tensile properties of S45C steel. Specimens were austenitized at 900°C, held for 45 minutes, and rapidly quenched in either water or oil. Mechanical tests included hardness measurement using the Rockwell C (HRC) scale, ultimate tensile load, and ultimate tensile strength testing conducted on a universal testing machine. The Hall-Petch theory was applied to analyze the relationship between grain size and hardness. Results demonstrate significant improvements in mechanical properties with both quenching methods. Water quenching achieved the maximum hardness (55.7 HRC) compared to untreated steel (25.6 HRC), representing a 118% enhancement, with an ultimate tensile strength of 891.4 MPa versus 632.3 MPa for the baseline (41% improvement). Oil quenching demonstrated a moderate increase in hardness to 42.9 HRC (68% enhancement) while achieving a superior ultimate tensile strength of 1041.3 MPa (65% improvement). These findings establish critical trade-offs in quenching media selection: water quenching maximizes hardness for wear-resistant applications, while oil quenching optimizes tensile strength for structural components requiring superior load-bearing capacity. </dc:description>
	<dc:publisher xml:lang="en-US">Universitas Mercu Buana</dc:publisher>
	<dc:date>2026-06-02</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/32215</dc:identifier>
	<dc:identifier>10.22441/sinergi.2026.2.002</dc:identifier>
	<dc:source xml:lang="en-US">SINERGI; Vol. 30 No. 2 (2026); 337-346</dc:source>
	<dc:source>2460-1217</dc:source>
	<dc:source>1410-2331</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://publikasi.mercubuana.ac.id/index.php/sinergi/article/view/32215/12478</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2026 SINERGI</dc:rights>
	<dc:rights xml:lang="en-US">https://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>