Melola Discovery

← Melola Discovery

Jurnal SINTA 1

Effect of Spring Back on Formation Process of Sheet Metal Bending Plates

Teknomekanik · Vol. 3 No. 1 (2020) · hlm. 28–35

DOI
10.24036/tm.v3i1.5872
ISSN
2621-8720, 2621-9980
Terbit
2020-05-25
Penerbit
Universitas Negeri Padang
Bahasa
eng

Abstrak

This study aims to observe the amount of deviation that occurs due to the influence of spring back on the forming process. spring back in question is the back force when the plate undergoes a forming process, but when the load is released, the plate condition will reverse or return to its initial condition. This reversal is due to the factor of the elasticity of the material that is owned. Other factors that influence the bending process include thickness, width, angle of bending and others. object of this research is a sheet metal plate with a thickness of 1 mm - 4 mm. Forming process is done by bending process. This bending process is widely used in the plate forming process, namely to bend the sides of the plate to make it stiffer. This bending process is carried out in cold conditions where the process is carried out at room temperature. This research was conducted by preparing slices of the same width and length and then the process of bending them to form an angle of 20 ° to 120 °. results of this test indicate that the thicker the bent material has the tendency to produce small deviations. This means that the value of the spring back ratio also decreases. The value of the spring back ratio in this study ranges from 1% to 9%. This means that if the bending process is carried out on a steel plate with the resulting bending angle of 90 °, the bending angle of the shoe must be more than 90 °, the excess is 1 ° - 9 °. So that when the load is released, the position of the susdut bends closer to 90 °.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 136 tautan kepenulisan bersama · 26 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Negeri Padang
  • State University of Medan
  • Universitas Syiah Kuala
  • Tun Hussein Onn University of Malaysia
  • Institut Agama Islam Negeri Kendari
  • Iloilo Science and Technology University
  • Vinh Long University of Technology Education
  • Organisasi lain
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Jasman JasmanUniversitas Negeri Padang7
Waskito WaskitoUniversitas Negeri Padang5
Irzal IrzalUniversitas Negeri Padang4
Budi SyahriUniversitas Negeri Padang3
Refdinal RefdinalUniversitas Negeri Padang3
A YufrizalUniversitas Negeri Padang2
Primawati PrimawatiUniversitas Negeri Padang2
Andre KurniawanUniversitas Negeri Padang2
Tze Kiong TeeTun Hussein Onn University of Malaysia2
Rizky Ema WulansariUniversitas Negeri Padang2
Yufrizal YufrizalUniversitas Negeri Padang2
Junil ArdiUniversitas Negeri Padang2
M Iksan ArdiyansyahUniversitas Negeri Padang1
Putu Satria RinaldoUniversitas Negeri Padang1
Ahmad Halim SidiqUniversitas Negeri Padang1
Ar TrisyaldiUniversitas Negeri Padang1
Syahril SyahrilUniversitas Negeri Padang1
Syahrul SyahrulInstitut Agama Islam Negeri Kendari1
Wakhinuddin WakhinuddinUniversitas Negeri Padang1
Abdul AzizUniversitas Negeri Padang1
Bahrul AminUniversitas Negeri Padang1
Yolli FernandaUniversitas Negeri Padang1
Muhammad Agung PratomoUniversitas Negeri Padang1
Muhammad RizkiUniversitas Negeri Padang1
Rodger EliabIloilo Science and Technology University1
Ahmad SabirinUniversitas Negeri Padang1
Muhammad Fikhri AldioUniversitas Negeri Padang1
Aprizal SaputraUniversitas Negeri Padang1
Chau Trung TinVinh Long University of Technology Education1
Janter Pangaduan SimanjuntakState University of Medan1
Binsar Maruli Tua PakpahanState University of Medan1
Khaled Ali Al-AttabUniversiti Sains Malaysia1
Muhammad Shadiq FahreziUniversitas Negeri Padang1
Firza FernandaUniversitas Negeri Padang1
Egi FadillahUniversitas Negeri Padang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Effect of Spring Back on Formation Process of Sheet Metal Bending Plates</dc:title>
	<dc:creator xml:lang="en">Purwantono, Purwantono</dc:creator>
	<dc:creator xml:lang="en">Erizon, Nelvi</dc:creator>
	<dc:creator xml:lang="en">Helmi, Nofri</dc:creator>
	<dc:creator xml:lang="en">Akhbar, Muhammad</dc:creator>
	<dc:creator xml:lang="en">Muhibuddin, Muhibuddin</dc:creator>
	<dc:subject xml:lang="en">Spring Back</dc:subject>
	<dc:subject xml:lang="en">Sheet metal</dc:subject>
	<dc:subject xml:lang="en">Bending</dc:subject>
	<dc:subject xml:lang="en">Elastisity</dc:subject>
	<dc:description xml:lang="en">This study aims to observe the amount of deviation that occurs due to the influence of spring back on the forming process. spring back in question is the back force when the plate undergoes a forming process, but when the load is released, the plate condition will reverse or return to its initial condition. This reversal is due to the factor of the elasticity of the material that is owned. Other factors that influence the bending process include thickness, width, angle of bending and others. object of this research is a sheet metal plate with a thickness of 1 mm - 4 mm. Forming process is done by bending process. This bending process is widely used in the plate forming process, namely to bend the sides of the plate to make it stiffer. This bending process is carried out in cold conditions where the process is carried out at room temperature. This research was conducted by preparing slices of the same width and length and then the process of bending them to form an angle of 20 ° to 120 °. results of this test indicate that the thicker the bent material has the tendency to produce small deviations. This means that the value of the spring back ratio also decreases. The value of the spring back ratio in this study ranges from 1% to 9%. This means that if the bending process is carried out on a steel plate with the resulting bending angle of 90 °, the bending angle of the shoe must be more than 90 °, the excess is 1 ° - 9 °. So that when the load is released, the position of the susdut bends closer to 90 °.</dc:description>
	<dc:publisher xml:lang="en">Universitas Negeri Padang</dc:publisher>
	<dc:date>2020-05-25</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/58</dc:identifier>
	<dc:identifier>10.24036/tm.v3i1.5872</dc:identifier>
	<dc:source xml:lang="en">Teknomekanik; Vol. 3 No. 1 (2020): Regular Issue; 28-35</dc:source>
	<dc:source>2621-8720</dc:source>
	<dc:source>2621-9980</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/58/29</dc:relation>
</oai_dc:dc>