Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Performance Analysis of Water Heating System by Using Double Glazed Flat Plate Solar Water Heater

Teknomekanik · Vol. 4 No. 1 (2021) · hlm. 1–7

DOI
10.24036/teknomekanik.v4i1.7872
ISSN
2621-8720, 2621-9980
Terbit
2021-05-24
Penerbit
Universitas Negeri Padang
Bahasa
eng
Lisensi
creativecommons.org/licenses/by/4.0

Abstrak

Nowadays, the use of solar energy is incredibly important to be increased since solar energy is renewable energy and also does not cause pollution. To harness solar energy, a solar collector device is needed to convert solar energy into heat energy. This study aimed to analyze the heat transfer in the flat plate solar collector which is used as a source of thermal energy in the water heating process for bathing. A double-glazed solar collector was used to absorb solar thermal energy and then transferred it to a water pipe. The pipe material used copper which has a very high conductivity value with an outer diameter of 15.7 mm. The plate collector used aluminium plates because they have high thermal conductivity. The dimensions of the collector frame were 150 cm long, 80 cm wide and 80 cm high. The collector frame was made of wood and covered with an insulator from coconut fibre with a thickness of 8 cm, with a tilt angle of 15˚. Based on the experimental process, the collector temperature was taken by using a thermocouple in order to heat the water which the inlet temperature in a bucket was 28˚C and the outlet water temperature during the experiment was 40˚C.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 127 tautan kepenulisan bersama · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Halu Oleo
  • Institut Agama Islam Negeri Kendari
  • Universitas Negeri Padang
  • Universitas Muhammadiyah Parepare
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Hendri NurdinAfiliasi tidak diketahui4
Yufrizal AAfiliasi tidak diketahui2
Budi SyahriAfiliasi tidak diketahui2
Kadir KadirUniversitas Halu Oleo1
La Ode Ahmad BarataAfiliasi tidak diketahui1
Takahiro KiwataAfiliasi tidak diketahui1
Dion Pratama PutraAfiliasi tidak diketahui1
Mursyidatul FadhliahAfiliasi tidak diketahui1
Yassirly Amrona RosyadaAfiliasi tidak diketahui1
Nurhidayah NurhidayahAfiliasi tidak diketahui1
Atun HomsatunInstitut Agama Islam Negeri Kendari1
Jamhari JamhariAfiliasi tidak diketahui1
Mefta SetianiAfiliasi tidak diketahui1
Nurhidayah NurhidayahAfiliasi tidak diketahui1
Fadhilah FadhilahAfiliasi tidak diketahui1
Andre KurniawanAfiliasi tidak diketahui1
Waskito WaskitoAfiliasi tidak diketahui1
Toto SugiartoAfiliasi tidak diketahui1
Rudy AnartaAfiliasi tidak diketahui1
Fathi Aulia DZAfiliasi tidak diketahui1
Meisuri HandayaniAfiliasi tidak diketahui1
Ambiyar AmbiyarUniversitas Negeri Padang1
Darmawi DarmawiAfiliasi tidak diketahui1
Sepdirama SetiawanAfiliasi tidak diketahui1
Defindo EfendiAfiliasi tidak diketahui1
Jasman JasmanUniversitas Muhammadiyah Parepare1
Nelvi ErizonAfiliasi tidak diketahui1
Muhammad Agung PratomoAfiliasi tidak diketahui1
Wagino WaginoAfiliasi tidak diketahui1
Batu Mahadi SiregarAfiliasi tidak diketahui1
Irzal IrzalAfiliasi tidak diketahui1
Eko IndrawanAfiliasi tidak diketahui1
Shih-Chen ShiAfiliasi tidak diketahui1
Dieter RahmadiawanAfiliasi tidak diketahui1
Wei-Ting ZhuangAfiliasi tidak diketahui1
Bagas SantosoAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 10 Nov 2026.
Metadata asli (oai_dc) 
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Performance Analysis of Water Heating System by Using Double Glazed Flat Plate Solar Water Heater</dc:title>
	<dc:creator xml:lang="en">Putra, Andika</dc:creator>
	<dc:creator xml:lang="en">K, Arwizet</dc:creator>
	<dc:creator xml:lang="en">Fernanda, Yolli</dc:creator>
	<dc:creator xml:lang="en">Sari, Delima Yanti</dc:creator>
	<dc:subject xml:lang="en">Solar Energy</dc:subject>
	<dc:subject xml:lang="en">Solar Collector</dc:subject>
	<dc:subject xml:lang="en">Solar Water</dc:subject>
	<dc:subject xml:lang="en">Double Plate Heater</dc:subject>
	<dc:subject xml:lang="en">Water Heating</dc:subject>
	<dc:description xml:lang="en">Nowadays, the use of solar energy is incredibly important to be increased since solar energy is renewable energy and also does not cause pollution. To harness solar energy, a solar collector device is needed to convert solar energy into heat energy. This study aimed to analyze the heat transfer in the flat plate solar collector which is used as a source of thermal energy in the water heating process for bathing. A double-glazed solar collector was used to absorb solar thermal energy and then transferred it to a water pipe. The pipe material used copper which has a very high conductivity value with an outer diameter of 15.7 mm. The plate collector used aluminium plates because they have high thermal conductivity. The dimensions of the collector frame were 150 cm long, 80 cm wide and 80 cm high. The collector frame was made of wood and covered with an insulator from coconut fibre with a thickness of 8 cm, with a tilt angle of 15˚. Based on the experimental process, the collector temperature was taken by using a thermocouple in order to heat the water which the inlet temperature in a bucket was 28˚C and the outlet water temperature during the experiment was 40˚C.</dc:description>
	<dc:publisher xml:lang="en">Universitas Negeri Padang</dc:publisher>
	<dc:date>2021-05-24</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/78</dc:identifier>
	<dc:identifier>10.24036/teknomekanik.v4i1.7872</dc:identifier>
	<dc:source xml:lang="en">Teknomekanik; Vol. 4 No. 1 (2021): Regular Issue; 1-7</dc:source>
	<dc:source>2621-8720</dc:source>
	<dc:source>2621-9980</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/78/37</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2021 Andika Putra, Arwizet K, Yolli Fernanda, Delima Yanti Sari</dc:rights>
	<dc:rights xml:lang="en">http://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>