Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Design, simulation, and static testing of an eco-friendly prosthetic foot using ramie-PLA composite

Teknomekanik · Vol. 8 No. 1 (2025) · hlm. 117–135

DOI
10.24036/teknomekanik.v8i1.36572
ISSN
2621-8720, 2621-9980
Terbit
2025-06-30
Penerbit
Universitas Negeri Padang
Bahasa
eng
Lisensi
creativecommons.org/licenses/by/4.0

Abstrak

This study developed a sustainable lower-limb prosthetic prototype using biodegradable ramie fiber-reinforced PLA composite as its primary material. The design specifically addresses the needs of individuals with limb amputation while prioritizing environmental sustainability. PLA-based composites for structural biomedical applications—particularly those in lower-limb prosthetics—must meet rigorous mechanical and fatigue performance requirements under repetitive loading. This study investigates the development of a transtibial prosthetic foot prototype using a quasi-isotropic lay-up prepreg ramie-PLA composite fabricated via the hot press method. Material characterization was conducted per ASTM standards, and the design was evaluated using the Finite Element Method (FEM). The prototype underwent static testing according to ISO 22675 with a user load criterion. The laminate exhibited an ultimate tensile strength of 48.36 ± 0.95 MPa, an elastic modulus of 4.125 ± 0.25 GPa, and a flexural strength of 62.06 ± 3.43 MPa. FEM results showed that all normal and shear stresses during heel strike (17.78 MPa and 1.71 MPa) and toe-off (12.38 MPa and 5.69 MPa) phases remained below fatigue limits. Experimental static stresses were heel strike (12.72 MPa) and toe-off (20.09 MPa), both within safe operational limits. These findings highlight the structural viability and environmental sustainability of ramie-PLA composites, positioning them as a promising material for next-generation prosthetic foot development.

Kata kunci

Jaringan kolaborasi para penulis

15 penulis · 83 tautan kepenulisan bersama · 36 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • National Research and Innovation Agency
  • University of Indonesia
  • Université Paris Nanterre
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Djoko Wahyu KarmiadjiNational Research and Innovation Agency2
Mustasyar PerkasaNational Research and Innovation Agency2
Yudan WhulanzaUniversity of Indonesia2
Arief SetyawanNational Research and Innovation Agency2
Rizky Pratama MulyanaNational Research and Innovation Agency2
Arga Agung NugrohoNational Research and Innovation Agency2
Wahyu SulistiyoNational Research and Innovation Agency2
Masripah MasripahNational Research and Innovation Agency2
Ridho DwimansyahNational Research and Innovation Agency2
Makmuri MakmuriNational Research and Innovation Agency2
Wely PasadenaNational Research and Innovation Agency2

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/oai, pertama di-harvest 10 Nov 2026, terakhir terlihat 10 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Design, simulation, and static testing of an eco-friendly prosthetic foot using ramie-PLA composite</dc:title>
	<dc:creator xml:lang="en">Sopiyan, Iyan</dc:creator>
	<dc:creator xml:lang="en">Soemardi, Tresna P.</dc:creator>
	<dc:creator xml:lang="en">Purnomo, Herry</dc:creator>
	<dc:creator xml:lang="en">Polit, Olivier</dc:creator>
	<dc:subject xml:lang="en">ramie fibers</dc:subject>
	<dc:subject xml:lang="en">PLA</dc:subject>
	<dc:subject xml:lang="en">bio-composite</dc:subject>
	<dc:subject xml:lang="en">lower limb prosthetic foot</dc:subject>
	<dc:subject xml:lang="en">prosthetic design and development</dc:subject>
	<dc:description xml:lang="en">This study developed a sustainable lower-limb prosthetic prototype using biodegradable ramie fiber-reinforced PLA composite as its primary material. The design specifically addresses the needs of individuals with limb amputation while prioritizing environmental sustainability. PLA-based composites for structural biomedical applications—particularly those in lower-limb prosthetics—must meet rigorous mechanical and fatigue performance requirements under repetitive loading. This study investigates the development of a transtibial prosthetic foot prototype using a quasi-isotropic lay-up prepreg ramie-PLA composite fabricated via the hot press method. Material characterization was conducted per ASTM standards, and the design was evaluated using the Finite Element Method (FEM). The prototype underwent static testing according to ISO 22675 with a user load criterion. The laminate exhibited an ultimate tensile strength of 48.36 ± 0.95 MPa, an elastic modulus of 4.125 ± 0.25 GPa, and a flexural strength of 62.06 ± 3.43 MPa. FEM results showed that all normal and shear stresses during heel strike (17.78 MPa and 1.71 MPa) and toe-off (12.38 MPa and 5.69 MPa) phases remained below fatigue limits. Experimental static stresses were heel strike (12.72 MPa) and toe-off (20.09 MPa), both within safe operational limits. These findings highlight the structural viability and environmental sustainability of ramie-PLA composites, positioning them as a promising material for next-generation prosthetic foot development.</dc:description>
	<dc:publisher xml:lang="en">Universitas Negeri Padang</dc:publisher>
	<dc:date>2025-06-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/365</dc:identifier>
	<dc:identifier>10.24036/teknomekanik.v8i1.36572</dc:identifier>
	<dc:source xml:lang="en">Teknomekanik; Vol. 8 No. 1 (2025): Regular Issue; 117-135</dc:source>
	<dc:source>2621-8720</dc:source>
	<dc:source>2621-9980</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>http://teknomekanik.ppj.unp.ac.id/index.php/teknomekanik/article/view/365/98</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2025 Iyan Sopiyan, Tresna P. Soemardi, Herry Purnomo, Olivier Polit</dc:rights>
	<dc:rights xml:lang="en">http://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>