Akses terbuka
Jurnal
SINTA 1
Optimization of Cu2O Thickness to Enhance Photocatalytic Properties of Electrodeposited Cu2O/FTO Photoanode
Bulletin of Chemical Reaction Engineering & Catalysis · Vol. ume (2024) · hlm. 108–117
ISSN 1978-2993
Terbit 2024-04-30
Penerbit Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)
Bahasa eng
Abstrak
Currently, n-type cuprous oxide (Cu2O) is a promising material as photocatalyst because of its energy gap of 2 eV that absorbs visible light up to a wavelength of 600 nm. As a photoelectrode, the thickness of Cu2O is crucial, where the improper thickness may worsen the photocatalytic properties. This work aimed to enhance the photocatalytic properties of Cu2O electrodeposited on fluorine-doped tin oxide (FTO), called Cu2O/FTO, by optimizing the Cu2O thickness. The thickness of Cu2O was controlled by adjusting the deposition time in the electrochemical deposition of Cu2O/FTO. By changing the deposition time from 5 to 45 min, the morphology of Cu2O changed from a leaf-like shape to an irregular facet shape with highly dense coverage, and the average thickness increased from 370 to 1100 nm. The increasing Cu2O thickness resulted in the increasing light absorption. The Cu2O/FTO demonstrated anodic photocurrent, which increased with the Cu2O thickness up to a threshold value of 1000 nm (35 min deposition time). At a thickness of 1000 nm, Cu2O/FTO achieved the highest photocurrent (150 and 58 µA under irradiation of 365 and 470 nm, respectively) due to the highly dense morphology and high absorption. In addition, with a thickness of 1000 nm, the charge diffusion was still good. Further, the increase of Cu2O film thickness higher than 1000 nm caused low photocatalytic properties even though the morphology was highly dense, and the absorption was the highest. This condition could be due to the relatively too-high resistance of Cu2O that caused poor charge diffusion. Copyright © 2024 by Authors, Published by BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Jaringan kolaborasi para penulis
16 penulis ·
39 tautan kepenulisan bersama
· 24 lintas organisasi
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
University of Indonesia National Research and Innovation Agency State University of Semarang Institut Teknologi Indonesia Indonesian Institute of Sciences Sunan Gunung Djati State Islamic University Bandung University of Mataram Organisasi lain Afiliasi tidak diketahui
Organisasi berbeda
Organisasi sama
Afiliasi tidak diketahui
Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.
Sumber metadata: OAI-PMH (metadata jurnal) https://journal.bcrec.id/index.php/bcrec/oai, pertama di-harvest 16 Nov 2026, terakhir terlihat 16 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/ http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
<dc:title xml:lang="en-US">Optimization of Cu2O Thickness to Enhance Photocatalytic Properties of Electrodeposited Cu2O/FTO Photoanode</dc:title>
<dc:creator>Khasanah, Riza Ariyani Nur</dc:creator>
<dc:creator>Chien, Forest Shih-Sen</dc:creator>
<dc:creator>Prasetyowati, Rita</dc:creator>
<dc:creator>Yudianti, Rike</dc:creator>
<dc:subject xml:lang="en-US">Cu2O; thickness; photocatalytic properties; electrochemical deposition; deposition time</dc:subject>
<dc:description xml:lang="en-US">Currently, n-type cuprous oxide (Cu2O) is a promising material as photocatalyst because of its energy gap of 2 eV that absorbs visible light up to a wavelength of 600 nm. As a photoelectrode, the thickness of Cu2O is crucial, where the improper thickness may worsen the photocatalytic properties. This work aimed to enhance the photocatalytic properties of Cu2O electrodeposited on fluorine-doped tin oxide (FTO), called Cu2O/FTO, by optimizing the Cu2O thickness. The thickness of Cu2O was controlled by adjusting the deposition time in the electrochemical deposition of Cu2O/FTO. By changing the deposition time from 5 to 45 min, the morphology of Cu2O changed from a leaf-like shape to an irregular facet shape with highly dense coverage, and the average thickness increased from 370 to 1100 nm. The increasing Cu2O thickness resulted in the increasing light absorption. The Cu2O/FTO demonstrated anodic photocurrent, which increased with the Cu2O thickness up to a threshold value of 1000 nm (35 min deposition time). At a thickness of 1000 nm, Cu2O/FTO achieved the highest photocurrent (150 and 58 µA under irradiation of 365 and 470 nm, respectively) due to the highly dense morphology and high absorption. In addition, with a thickness of 1000 nm, the charge diffusion was still good. Further, the increase of Cu2O film thickness higher than 1000 nm caused low photocatalytic properties even though the morphology was highly dense, and the absorption was the highest. This condition could be due to the relatively too-high resistance of Cu2O that caused poor charge diffusion. Copyright © 2024 by Authors, Published by BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).</dc:description>
<dc:publisher xml:lang="en-US">Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)</dc:publisher>
<dc:date>2024-04-30</dc:date>
<dc:type>info:eu-repo/semantics/article</dc:type>
<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
<dc:type xml:lang="en-US"></dc:type>
<dc:format>application/pdf</dc:format>
<dc:identifier>https://journal.bcrec.id/index.php/bcrec/article/view/20081</dc:identifier>
<dc:identifier>10.9767/bcrec.20081</dc:identifier>
<dc:source xml:lang="en-US">Bulletin of Chemical Reaction Engineering & Catalysis; 2024: BCREC Volume 19 Issue 1 Year 2024 (April 2024); 108-117</dc:source>
<dc:source>1978-2993</dc:source>
<dc:language>eng</dc:language>
<dc:relation>https://journal.bcrec.id/index.php/bcrec/article/view/20081/9685</dc:relation>
<dc:rights xml:lang="en-US">Copyright (c) 2024 by Authors, Published by BCREC Group</dc:rights>
<dc:rights xml:lang="en-US">https://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>
Sitasi dan pengindeksan
OpenAlex
Belum diperiksa
Crossref
Terindeks
lewat DOI
3 sitasi
Jumlah menurut tiap indeks pada 16 Nov 2026; setiap indeks menghitung sitasi dengan cara berbeda.
Sitasi artikel ini
APA 7
Khasanah, R. A. N., Chien, F. S. S., Prasetyowati, R., & Yudianti, R. (2024). Optimization of Cu2O Thickness to Enhance Photocatalytic Properties of Electrodeposited Cu2O/FTO Photoanode. Bulletin of Chemical Reaction Engineering & Catalysis, ume, 108–117. https://doi.org/10.9767/bcrec.20081
Salin
IEEE
R. A. N. Khasanah, F. S. S. Chien, R. Prasetyowati, and R. Yudianti, “Optimization of Cu2O Thickness to Enhance Photocatalytic Properties of Electrodeposited Cu2O/FTO Photoanode,” Bulletin of Chemical Reaction Engineering & Catalysis, vol. ume, pp. 108–117, 2024, doi: 10.9767/bcrec.20081.
Salin
Dibuat dari metadata jurnal; periksa nama penulis sebelum dipakai.