Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Effect of Temperature Variation of Static Thermal Tensioning on Angular Distortion and Sensitization behavior of GMAW Welded SUS 304 Stainless Steel Plate

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 21 No. 3 (2021) · hlm. 218–224

DOI
10.31940/logic.v21i3.218-224
ISSN
2580-5649, 1412-114X
Terbit
2021-11-30
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

Due to its rust resistance properties, the use of stainless steels, especially SUS304 for industrial equipment is increasing. The manufacturing process that is often used is GMAW welding. One of the disadvantages of SUS304 is the occurrence of distortion and sensitization when welded. In this study, the effect of temperature variations of Static Thermal Tensioning on angle distortion and microstructure behavior due to GMAW welding of SUS 304 T-joint plates was studied. Heating by electric heater is given to both parts of the base metal plate SUS 304 5mm thick with temperature variations of 200 oC, 250 oC and 300 oC. Cooling water with a temperature of 24 oC is provided on the back side of the welded track. Welding using filler ER 304 with a diameter of 0.8 mm with welding parameters such as welding current, voltage, gas flow and travel speed controlled at 75 A, 22 V, 10 l/min and 8 mm/s, respectively. Angular distortion of welding results for each treatment temperature variation was measured using a bevel protractor, and perform metallographic test to knowing the microstructural behavior. The results of the measurement of the average angular distortion of three repetitions show that at a temperature of 250 C static thermal tensioning produces the smallest angular distortion of 3ᵒ70', compared to other temperature variations which produce angular distortion 4o45’ at 200 oC and 3o86' at temperature 300 oC. The findings of the largest Cr (carbide) deposits due to sensitization were found at a temperature of 300 oC at 16,49% and the lowest at a temperature of 200 oC at 7,05%

Kata kunci

Jaringan kolaborasi para penulis

22 penulis · 47 tautan kepenulisan bersama · 1 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Universitas Gadjah Mada
  • State University of Semarang
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Anggit MurdaniPoliteknik Negeri Malang5
Naufal Reza PutraAfiliasi tidak diketahui3
SubagiyoAfiliasi tidak diketahui2
MaryonoAfiliasi tidak diketahui1
WinarsihState University of Semarang1
Syahrul FauziUniversitas Gadjah Mada1
Syamsul HadiPoliteknik Negeri Malang1
SarjiyanaAfiliasi tidak diketahui1
Samsul HadiPoliteknik Negeri Malang1
Muhamad Zidan WibowoPoliteknik Negeri Malang1
Syamsul HadiPoliteknik Negeri Malang1
Muhammad Naufal Abiyyi HutagalungPoliteknik Negeri Malang1
Firman DwiyantoPoliteknik Negeri Malang1
Dadang KurniawanPoliteknik Negeri Malang1
Sugeng Hadi SusiloPoliteknik Negeri Malang1
Zahratul JannahPoliteknik Negeri Malang1
Imam MashudiPoliteknik Negeri Malang1
Agus HardjitoPoliteknik Negeri Malang1
Listiono ListionoPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Effect of Temperature Variation of Static Thermal Tensioning on Angular Distortion and Sensitization behavior of GMAW Welded SUS 304 Stainless Steel Plate</dc:title>
	<dc:creator>R.N. Akhsanu Takwim</dc:creator>
	<dc:creator>Purwoko</dc:creator>
	<dc:creator>Bayu Pranoto</dc:creator>
	<dc:subject xml:lang="en-US">static thermal tensioning</dc:subject>
	<dc:subject xml:lang="en-US">sensitization</dc:subject>
	<dc:subject xml:lang="en-US">SUS 304</dc:subject>
	<dc:subject xml:lang="en-US">GMAW</dc:subject>
	<dc:subject xml:lang="en-US">angular distortion</dc:subject>
	<dc:description xml:lang="en-US">Due to its rust resistance properties, the use of stainless steels, especially SUS304 for industrial equipment is increasing.
The manufacturing process that is often used is GMAW welding.&amp;nbsp;One of the disadvantages of SUS304 is the occurrence of distortion and sensitization when welded.&amp;nbsp;In this study, the effect of temperature variations of Static Thermal Tensioning on angle distortion and microstructure behavior due to GMAW welding of SUS 304 T-joint plates was studied. Heating by electric heater is given to both parts of the base metal plate SUS 304 5mm thick with temperature variations of 200 oC, 250 oC and 300 oC. Cooling water with a temperature of 24 oC is provided on the back side of the welded track. Welding using filler ER 304 with a diameter of 0.8 mm with welding parameters such as welding current, voltage, gas flow and travel speed controlled at 75 A, 22 V, 10 l/min and 8 mm/s, respectively. Angular distortion of welding results for each treatment temperature variation was measured using a bevel protractor, and perform metallographic test to knowing the microstructural behavior. The results of the measurement of the average angular distortion of three repetitions show that at a temperature of 250 C static thermal tensioning produces the smallest angular distortion of 3ᵒ70', compared to other temperature variations which produce angular distortion 4o45’ at 200 oC and 3o86' at temperature 300 oC.&amp;nbsp;The findings of the largest Cr (carbide) deposits due to sensitization were found at a temperature of 300 oC at 16,49% and the lowest at a temperature of 200 oC at 7,05%</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2021-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/98</dc:identifier>
	<dc:identifier>10.31940/logic.v21i3.218-224</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 21 No. 3 (2021): November; 218-224</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v21i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/98/49</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2021  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>