Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Effect of Forging Deformation and Cooling on Mechanical Properties of Martensitic Stainless Steel

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 21 No. 3 (2021) · hlm. 225–231

DOI
10.31940/logic.v21i3.225-231
ISSN
2580-5649, 1412-114X
Terbit
2021-11-30
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

Stainless steel has good mechanical properties compared to other materials for strength and hardness, usually it will increase in hardness after hardening or forging. The purpose of this study was to obtain information about: The value of hardness and tensile strength of martensitic stainless steel forging with various deformations and cooling. The research method used is an experimental method, namely by forging on martensitic stainless steel with variations in deformation and cooling rate. Variations of forging deformation used are 25%, 50%, and 75%. The cooling media used are water, oil and air. The results of forgings with various cooling media were tested for tensile strength and tested for hardness using the Rockwell C (HRC) method. It was found that the higher the value of forging deformation, the higher the value of strength and hardness of martensitic stainless steel. This is because more and more martensite structures are recrystallized. In addition, it was also found that water and air cooling media gave an increase in the hardness of martensitic stainless steels. This is influenced by the cooling rate, where the higher the cooling rate, the more martensite structures formed, thus increasing the hardness value. The increase in hardness value is proportional to the increase in yield strength and tensile strength.

Kata kunci

Jaringan kolaborasi para penulis

16 penulis · 34 tautan kepenulisan bersama · 1 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • University of Brawijaya
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
R.N. Akhsanu TakwimPoliteknik Negeri Malang3
PurwokoAfiliasi tidak diketahui2
Anggit MurdaniPoliteknik Negeri Malang2
Samsul HadiPoliteknik Negeri Malang2
Muhamad Zidan WibowoPoliteknik Negeri Malang2
Faizatul AmaliaUniversity of Brawijaya1
Radhi Nurvian AmrullahPoliteknik Negeri Malang1
Naufal Reza PutraAfiliasi tidak diketahui1
Syamsul HadiPoliteknik Negeri Malang1
Muhammad Naufal Abiyyi HutagalungPoliteknik Negeri Malang1
Firman DwiyantoPoliteknik Negeri Malang1
Dadang KurniawanPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Effect of Forging Deformation and Cooling on Mechanical Properties of Martensitic Stainless Steel</dc:title>
	<dc:creator>Subagiyo</dc:creator>
	<dc:creator>Syamsul Hadi</dc:creator>
	<dc:creator>Sarjiyana</dc:creator>
	<dc:creator>Bayu Pranoto</dc:creator>
	<dc:subject xml:lang="en-US">martensitic stainless steel</dc:subject>
	<dc:subject xml:lang="en-US">forging deformation</dc:subject>
	<dc:subject xml:lang="en-US">cooling rate</dc:subject>
	<dc:subject xml:lang="en-US">tensile strength</dc:subject>
	<dc:subject xml:lang="en-US">hardness</dc:subject>
	<dc:subject xml:lang="en-US">yield strength</dc:subject>
	<dc:subject xml:lang="en-US">elongation</dc:subject>
	<dc:description xml:lang="en-US">Stainless steel has good mechanical properties compared to other materials for strength and hardness, usually it will increase in hardness after hardening or forging. The purpose of this study was to obtain information about: The value of hardness and tensile strength of martensitic stainless steel forging with various deformations and cooling. The research method used is an experimental method, namely by forging on martensitic stainless steel with variations in deformation and cooling rate. Variations of forging deformation used are 25%, 50%, and 75%. The cooling media used are water, oil and air. The results of forgings with various cooling media were tested for tensile strength and tested for hardness using the Rockwell C (HRC) method. It was found that the higher the value of forging deformation, the higher the value of strength and hardness of martensitic stainless steel. This is because more and more martensite structures are recrystallized. In addition, it was also found that water and air cooling media gave an increase in the hardness of martensitic stainless steels. This is influenced by the cooling rate, where the higher the cooling rate, the more martensite structures formed, thus increasing the hardness value. The increase in hardness value is proportional to the increase in yield strength and tensile strength.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2021-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/99</dc:identifier>
	<dc:identifier>10.31940/logic.v21i3.225-231</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 21 No. 3 (2021): November; 225-231</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v21i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/99/50</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2021  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>