Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Implementation of Inverse Kinematic and Trajectory Planning on 6-DOF Robotic Arm for Straight-Flat Welding Movement

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 22 No. 1 (2022) · hlm. 51–61

DOI
10.31940/logic.v22i1.51-61
ISSN
2580-5649, 1412-114X
Terbit
2022-03-30
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

Robotic arms have been used in various processes such as for moving goods, welding, assembling, and painting. In the case of welding and painting, it is necessary to move the end-effector robot accurately and smoothly to follow the specified trajectory. In robotic arm control, 2 things are important to be analyzed and implemented in controlling the motion of the robotic arm, namely inverse kinematic and trajectory planning. In this study, the inverse kinematic and trajectory planning algorithms are implemented to the robotic arm controller in the form of an Arduino Mega 2560 microcontroller. The inverse kinematic solution uses geometric and algebraic analytical methods. while the trajectory planning method is using LSPB (Linear Segment Parabolic Blend) Trajectory in Cartesian Space. Data retrieval is done by giving 2 input coordinates of the desired position and orientation, then the data in the form of the joint angle value will be measured using a rotary encoder as an angle sensor. Furthermore, the joint angle measurement value is converted in cartesian coordinates to get the end-effector position. Data analysis is done by comparing the data value of each joint angle with the calculated value so that the error value appears. The results showed that the inverse kinematic and trajectory planning algorithms were successfully applied to the 6-DOF robotic arm to perform straight-flat welding movements. Inverse kinematic testing on both input coordinates, the average error value for joints 2, 3, and 5 is 1.82º, 1.26º, and 2.08º. Meanwhile, the average error of the end-effector position at the x and z coordinates is 2.08 mm and 12.9 mm, respectively. Then for the trajectory planning test, the error value for the end-effector position in the x and z coordinates is 2.25 mm and 10.7 mm.

Kata kunci

Jaringan kolaborasi para penulis

16 penulis · 33 tautan kepenulisan bersama · 9 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Jakarta State Polytechnic
  • Indonesia University of Education
  • State University of Semarang
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Heru PrasetyoPoliteknik Negeri Malang1
Kris WitonoPoliteknik Negeri Malang1
Pondi UdiantoPoliteknik Negeri Malang1
Agus SetiawanIndonesia University of Education1
SuryantoAfiliasi tidak diketahui1
Eko YudiyantoPoliteknik Negeri Malang1
Khambali KhambaliPoliteknik Negeri Malang1
Falih AlauddinPoliteknik Negeri Malang1
R.N. Akhsanu TakwimPoliteknik Negeri Malang1
Zahratul JannahPoliteknik Negeri Malang1
Asrori AsroriState University of Semarang1
Mira Esculenta MartawatiPoliteknik Negeri Malang1
W LulutPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Implementation of Inverse Kinematic and Trajectory Planning on 6-DOF Robotic Arm for Straight-Flat Welding Movement</dc:title>
	<dc:creator>Muhammad Arif Nur Huda</dc:creator>
	<dc:creator>Sugeng Hadi Susilo</dc:creator>
	<dc:creator>Pribadi Mumpuni Adhi</dc:creator>
	<dc:subject xml:lang="en-US">inverse kinematic</dc:subject>
	<dc:subject xml:lang="en-US"> trajectory planning</dc:subject>
	<dc:subject xml:lang="en-US">robotic arm </dc:subject>
	<dc:subject xml:lang="en-US">DOF</dc:subject>
	<dc:subject xml:lang="en-US">welding movement</dc:subject>
	<dc:description xml:lang="en-US">Robotic arms have been used in various processes such as for moving goods, welding, assembling, and painting. In the case of welding and painting, it is necessary to move the end-effector robot accurately and smoothly to follow the specified trajectory. In robotic arm control, 2 things are important to be analyzed and implemented in controlling the motion of the robotic arm, namely inverse kinematic and trajectory planning. In this study, the inverse kinematic and trajectory planning algorithms are implemented to the robotic arm controller in the form of an Arduino Mega 2560 microcontroller. The inverse kinematic solution uses geometric and algebraic analytical methods. while the trajectory planning method is using LSPB (Linear Segment Parabolic Blend) Trajectory in Cartesian Space. Data retrieval is done by giving 2 input coordinates of the desired position and orientation, then the data in the form of the joint angle value will be measured using a rotary encoder as an angle sensor. Furthermore, the joint angle measurement value is converted in cartesian coordinates to get the end-effector position. Data analysis is done by comparing the data value of each joint angle with the calculated value so that the error value appears. The results showed that the inverse kinematic and trajectory planning algorithms were successfully applied to the 6-DOF robotic arm to perform straight-flat welding movements. Inverse kinematic testing on both input coordinates, the average error value for joints 2, 3, and 5 is 1.82º, 1.26º, and 2.08º. Meanwhile, the average error of the end-effector position at the x and z coordinates is 2.08 mm and 12.9 mm, respectively. Then for the trajectory planning test, the error value for the end-effector position in the x and z coordinates is 2.25 mm and 10.7 mm.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2022-03-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/385</dc:identifier>
	<dc:identifier>10.31940/logic.v22i1.51-61</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 22 No. 1 (2022): March; 51-61</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v22i1</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/385/220</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2022  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>