Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Tensile Strength Analysis of AISI 1045 Steel Results of Smaw Welding Using Variations of Preheat and Cooling Media

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 22 No. 3 (2022) · hlm. 214–224

DOI
10.31940/logic.v22i3.214-224
ISSN
2580-5649, 1412-114X
Terbit
2022-11-30
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

In the welding process, there are many factors that need to be considered, including heat input, cooling rate, the material being welded, and the use of added materials, if these factors are not considered, they can cause cracks in the American Iron & Steel Institute (AISI) 1045 material. to determine the effect of preheat variations on tensile strength, the effect of cooling media on tensile strength, and to determine the interaction of preheat variations and cooling media on tensile strength. This research method used experimentally by varying the preheat temperature 250⁰C, 325⁰C, 400⁰C, and the cooling medium was lime, sand, and normal air, then tensile test was carried out. The results showed that the cooling medium affected the tensile strength with the highest tensile strength of 64.35 kg/mm2 on the sand cooling medium, while the preheat variation had no effect on the tensile strength as shown by a graph close to the horizontal straight at the tensile strength ranging from 60 kg/mm2, interaction between preheat and cooling medium has no effect on tensile strength. This is indicated by the tensile strength values ​​that are almost close to each preheat point, namely at a temperature of 250⁰C between 53-67 kg/mm2, at 325⁰C between 56-60 kg/mm2, and a temperature of 400⁰C between 51-64 kg/mm2. In this study it can be concluded that a good cooling medium uses sand media with a preheat temperature of 250⁰C.

Kata kunci

Jaringan kolaborasi para penulis

15 penulis · 33 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
R.N. Akhsanu TakwimPoliteknik Negeri Malang3
PurwokoAfiliasi tidak diketahui2
Anggit MurdaniPoliteknik Negeri Malang2
Syamsul HadiPoliteknik Negeri Malang2
SarjiyanaAfiliasi tidak diketahui2
Radhi Nurvian AmrullahPoliteknik Negeri Malang1
Naufal Reza PutraAfiliasi tidak diketahui1
Syamsul HadiPoliteknik Negeri Malang1
Muhammad Naufal Abiyyi HutagalungPoliteknik Negeri Malang1
Firman DwiyantoPoliteknik Negeri Malang1
Dadang KurniawanPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Tensile Strength Analysis of AISI 1045 Steel Results of Smaw Welding Using Variations of Preheat and Cooling Media</dc:title>
	<dc:creator>Pranoto, Bayu</dc:creator>
	<dc:creator>Subagiyo</dc:creator>
	<dc:creator>Samsul Hadi</dc:creator>
	<dc:creator>Muhamad Zidan Wibowo </dc:creator>
	<dc:subject xml:lang="en-US">Tensile Strength</dc:subject>
	<dc:subject xml:lang="en-US">Cooling Media</dc:subject>
	<dc:subject xml:lang="en-US">Welding</dc:subject>
	<dc:subject xml:lang="en-US">Preheat</dc:subject>
	<dc:subject xml:lang="en-US">SMAW</dc:subject>
	<dc:description xml:lang="en-US">In the welding process, there are many factors that need to be considered, including heat input, cooling rate, the material being welded, and the use of added materials, if these factors are not considered, they can cause cracks in the American Iron &amp;amp; Steel Institute (AISI) 1045 material. to determine the effect of preheat variations on tensile strength, the effect of cooling media on tensile strength, and to determine the interaction of preheat variations and cooling media on tensile strength. This research method used experimentally by varying the preheat temperature 250⁰C, 325⁰C, 400⁰C, and the cooling medium was lime, sand,&amp;nbsp;and normal air, then tensile test was carried out. The results showed that the cooling medium affected the tensile strength with the highest tensile strength of 64.35 kg/mm2 on the sand cooling medium, while the preheat variation had no effect on the tensile strength as shown by a graph close to the horizontal straight at the tensile strength ranging from 60 kg/mm2, interaction between preheat and cooling medium has no effect on tensile strength. This is indicated by the tensile strength values ​​that are almost close to each preheat point, namely at a temperature of 250⁰C between 53-67 kg/mm2, at 325⁰C between 56-60 kg/mm2, and a temperature of 400⁰C between 51-64 kg/mm2. In this study it can be concluded that a good cooling medium uses sand media with a preheat temperature of 250⁰C.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2022-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/520</dc:identifier>
	<dc:identifier>10.31940/logic.v22i3.214-224</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 22 No. 3 (2022): November; 214-224</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v22i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/520/403</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2022  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>