Melola Discovery

← Melola Discovery

Jurnal SINTA 3

The Effect of Holding Pressure and Inject Pressure to Short Shot Defect in Injection Molding Cover Pot: Pengaruh Holding Pressure dan Inject Pressure Terhadap Short Shot Defect pada Proses Injection Molding Cover Pot

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 23 No. 2 (2023) · hlm. 147–154

DOI
10.31940/logic.v23i2.147-154
ISSN
2580-5649, 1412-114X
Terbit
2023-07-31
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

The influence of inappropriate injection molding parameters often results in product defects, one of which is the short shot, which is a condition where the plastic to be injected into the cavity does’t reach the ideal capacity. The purpose of this research is to understand and be able to explain the parameters of holding pressure, inject pressure, and the interaction of these two parameters on short shot defects in cover pot products with the injection molding process. This research uses independent variables, namely holding pressure with variations of 20 Bar, 30 Bar, and 40 Bar and inject pressure with variations of 15 Bar, 30 Bar, and 45 Bar and dependent variables in the form of short shot defects. The method used in this research is a factorial experiment with replication of 10 (ten) times and data processing analysis using ANOVA with the help of Minitab 21.2.0 statistical software. The result of this research is that there is a significant influence of holding pressure, inject pressure, and the interaction of these two parameters on short shot defects in cover pot products with injection molding process. The average weight of the product produced at the interaction of the parameters holding pressure 40 Bar and inject pressure 45 Bar is 8.8 grams (normal) so as to minimize product defects to improve the quality and quantity of cosmetic packaging production cover pot.

Kata kunci

Jaringan kolaborasi para penulis

6 penulis · 7 tautan kepenulisan bersama · 1 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Hosei University
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Haris Puspito BuwonoPoliteknik Negeri Malang1
Nurlia Pramita SariPoliteknik Negeri Malang1
Syamsul HadiHosei University1
R.N. Akhsanu TakwinAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">The Effect of Holding Pressure and Inject Pressure  to Short Shot Defect in Injection Molding Cover Pot: Pengaruh Holding Pressure dan Inject Pressure Terhadap Short Shot Defect pada Proses Injection Molding Cover Pot</dc:title>
	<dc:creator>Muhammad Sambodo Aribowo</dc:creator>
	<dc:creator>Dani, Agus</dc:creator>
	<dc:subject xml:lang="en-US">Holding pressure</dc:subject>
	<dc:subject xml:lang="en-US">Inject pressure</dc:subject>
	<dc:subject xml:lang="en-US">Injection molding</dc:subject>
	<dc:subject xml:lang="en-US">Polystyrene</dc:subject>
	<dc:subject xml:lang="en-US">Short shot</dc:subject>
	<dc:description xml:lang="en-US">The influence&amp;nbsp;of inappropriate injection molding&amp;nbsp; parameters often results in product defects, one of&amp;nbsp; which is the short shot, which is a condition where the plastic to be injected into&amp;nbsp; the cavity does’t reach the ideal capacity. The purpose of this research is&amp;nbsp; to understand and be able to explain&amp;nbsp; the parameters of holding pressure, inject pressure, and the interaction of these two parameters on short shot defects in&amp;nbsp;&amp;nbsp; cover pot products&amp;nbsp; with the injection molding process. This research uses independent variables, namely holding pressure with variations of 20 Bar, 30 Bar, and 40 Bar and inject pressure with variations of 15 Bar, 30 Bar, and 45 Bar and dependent&amp;nbsp;variables in the form of short shot defects. The method used in this research is a factorial experiment with replication of 10 (ten) times and data processing analysis using ANOVA with the help of&amp;nbsp; Minitab 21.2.0 statistical software. The result of this research is that there is a significant influence&amp;nbsp;of holding pressure, inject pressure, and the interaction of these two parameters on short shot defects&amp;nbsp; in cover pot products&amp;nbsp; with injection molding process.&amp;nbsp;The average weight of the product produced at the interaction&amp;nbsp; of the parameters holding pressure 40 Bar and inject pressure 45 Bar is 8.8 grams (normal) so as to minimize product defects to improve the quality and quantity of cosmetic packaging production cover pot.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2023-07-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/1099</dc:identifier>
	<dc:identifier>10.31940/logic.v23i2.147-154</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 23 No. 2 (2023): July; 147-154</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v23i2</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/1099/644</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2023  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>