Melola Discovery

← Melola Discovery

Jurnal SINTA 3

THE EFFECT OF THE ANGLE AND DIMENSIONS OF A CROSS-SECTION SPECIMEN ON THE TORSIONAL STRENGTH OF AISI 1020 SQUARE STEEL SHAFT

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 24 No. 1 (2024) · hlm. 9–16

DOI
10.31940/logic.v24i1.9-16
ISSN
2580-5649, 1412-114X
Terbit
2024-03-31
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

The unknown torsional strength due to the inconsistency of the angles and dimensions of the square cross-section of AISI 1020 steel specimens in the torsion test is the problem encountered. The research method included: preparation of square AISI 1020 steel specimens measuring 6 mm x 6 mm x 160 mm, measurement of 2 diagonal angles of the cross section of the specimen and dimensions of the cross section at 5 observation points along the specimen receiving torsion loads, torsion testing of specimens, analysis of torsion test results data, and drawing conclusions. The results of the study affect the angle and dimensions of the specimen cross-section on the torsional strength of the AISI 1020 steel square shaft which has a greater value at the angles of 89o and 91o than 90o which with an angle of 89o at dimensions of 5.96 mm x 5.96 mm has a torsional strength of 412 MPa, while at an angle of 90o with dimensions of 5.96 mm x 5.96 mm it has a torsional strength of 359 MPa, and for an angle of 91o in dimensions of 5.95 mm x 5.95 mm has a torsional strength of 402 MPa. The average torsional strength is achieved in the range of 351 to 397 MPa, at an angle of 89o the torsional strength increases by 46 MPa or around 13.1 %, and at an angle of 91o the torsional strength increases by 43 MPa or around 12.3%.

Kata kunci

Jaringan kolaborasi para penulis

22 penulis · 59 tautan kepenulisan bersama · 6 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • Lambung Mangkurat University
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Syamsul HadiPoliteknik Negeri Malang2
Heru PrasetyoPoliteknik Negeri Malang1
Pondi UdiantoPoliteknik Negeri Malang1
Sugeng Hadi SusiloPoliteknik Negeri Malang1
Sudarmadji .Afiliasi tidak diketahui1
Nila AliaPoliteknik Negeri Malang1
Bambang IrawanLambung Mangkurat University1
Anggit MurdaniPoliteknik Negeri Malang1
Andhika Erlangga Setiawan PutraPoliteknik Negeri Malang1
Sza Sya Monica ValeriaPoliteknik Negeri Malang1
Aji TisaPoliteknik Negeri Malang1
Bagus WahyudiPoliteknik Negeri Malang1
Septyana RiskitasariPoliteknik Negeri Malang1
Talifatim MachfurohPoliteknik Negeri Malang1
Etik PuspitasariPoliteknik Negeri Malang1
Muhammad Akhlis RizzaPoliteknik Negeri Malang1
Ahmad Hailala Nur AzizPoliteknik Negeri Malang1
Pipit Wahyu NugrohoPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">THE EFFECT OF THE ANGLE AND DIMENSIONS OF A CROSS-SECTION SPECIMEN ON THE TORSIONAL STRENGTH OF AISI 1020 SQUARE STEEL SHAFT</dc:title>
	<dc:creator>Bima Cahya Maula Dana</dc:creator>
	<dc:creator>Syamsul</dc:creator>
	<dc:creator>Hangga Wicaksono</dc:creator>
	<dc:creator>Kris Witono </dc:creator>
	<dc:subject xml:lang="en-US">specimen cross-sectional angle</dc:subject>
	<dc:subject xml:lang="en-US">specimen cross-sectional dimensions</dc:subject>
	<dc:subject xml:lang="en-US">AISI 1020 steel</dc:subject>
	<dc:subject xml:lang="en-US">square shaft</dc:subject>
	<dc:subject xml:lang="en-US">torsional  strength</dc:subject>
	<dc:description xml:lang="en-US">The unknown torsional strength due to the inconsistency of the angles and dimensions of the square cross-section of AISI 1020 steel specimens in the torsion test is the problem encountered. The research method included: preparation of square AISI 1020 steel specimens measuring 6 mm x 6 mm x 160 mm, measurement of 2 diagonal angles of the cross section of the specimen and dimensions of the cross section at 5 observation points along the specimen receiving torsion loads, torsion testing of specimens, analysis of torsion test results data, and drawing conclusions. The results of the study affect the angle and dimensions of the specimen cross-section on the torsional strength of the AISI 1020 steel square shaft which has a greater value at the angles of 89o and 91o than 90o which with an angle of 89o at dimensions of 5.96 mm x 5.96 mm has a torsional strength of 412 MPa, while at an angle of 90o with dimensions of 5.96 mm x 5.96 mm it has a torsional strength of 359 MPa, and for an angle of 91o in dimensions of 5.95 mm x 5.95 mm has a torsional strength of 402 MPa. The average torsional strength is achieved in the range of 351 to 397 MPa,&amp;nbsp;at an angle of 89o the torsional strength increases by 46 MPa or around 13.1 %,&amp;nbsp;and at an angle of 91o the torsional strength increases by 43 MPa or around 12.3%.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2024-03-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/1410</dc:identifier>
	<dc:identifier>10.31940/logic.v24i1.9-16</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 24 No. 1 (2024): March; 9-16</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v24i1</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/1410/824</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2024  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>