Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Analysis of Leakage Test Results on Flange-Gasket Piping System Simulator Device

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 25 No. 1 (2025) · hlm. 27–34

DOI
10.31940/logic.v25i1.27-34
ISSN
2580-5649, 1412-114X
Terbit
2025-03-30
Penerbit
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Bahasa
eng

Abstrak

Fluid leaks in piping installations often occur in the industrial sector which is detrimental due to the selection of gasket materials, flanges, and improper tightening torque of flange bolts. The fluids that are flowed can be clean water, palm oil with a fatty acid content at an acidity level (pH) of around 4, oil, solutions with a certain pH or fuel. The purpose of the simulator device analysis is to obtain data on the level of tightening torque of bolts-nuts on 1 inch pipe flanges-gaskets and the volume of leakage. The analysis method includes setting the working pressure of the fluid on the globe valve at 1 Bar, 1.3 Bar, and 1.5 Bar on the flange-gasket piping system simulator device, measuring the lowest tightening torque at which the fluid starts to leak to the highest at a condition where there is no leak at all, and two-way Anova analysis on the distribution data. The results of the study showed that the lowest bolt-nut tightening torque at 2 Nm for three M8 bolts-nuts as flange-gasket pair locks resulted in an average fluid droplet leakage of 120 ml/hour and at a torque of 4 Nm the leakage level was about a quarter of that, namely 36 ml/hour and finally at a torque of 5 Nm there was no leakage at all. Implications in industries that use fluid flow with sufficient tightening torque of nuts-bolts on flanges-gaskets can reduce-stop losses due to leakage that occurs in their piping systems.

Kata kunci

Jaringan kolaborasi para penulis

40 penulis · 102 tautan kepenulisan bersama · 22 lintas organisasi · menampilkan 40 yang paling banyak terhubung

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Malang
  • University of Sarjanawiyata Tamansiswa
  • Politeknik Pertanian Negeri Pangkajene Kepulauan
  • Lambung Mangkurat University
  • Jakarta State Polytechnic
  • University of Technology Malaysia
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
R.N. Akhsanu TakwimPoliteknik Negeri Malang3
Anggit MurdaniPoliteknik Negeri Malang3
PurwokoAfiliasi tidak diketahui2
SubagiyoAfiliasi tidak diketahui2
Nila AliaPoliteknik Negeri Malang2
Hangga WicaksonoPoliteknik Negeri Malang2
Andri SetiawanPoliteknik Negeri Malang2
Muhammad RiyadiPoliteknik Pertanian Negeri Pangkajene Kepulauan1
Irawan IlhamPoliteknik Pertanian Negeri Pangkajene Kepulauan1
Eko Sulkhany YuliantoUniversity of Sarjanawiyata Tamansiswa1
Tito Aji MilleniawanUniversity of Sarjanawiyata Tamansiswa1
Mohammad Ahyar Syafwan LysanderUniversity of Sarjanawiyata Tamansiswa1
Shahnur Al-HafriUniversity of Sarjanawiyata Tamansiswa1
Didik SubiyantoUniversity of Sarjanawiyata Tamansiswa1
Tri Aji PurnomoUniversity of Sarjanawiyata Tamansiswa1
Nanang QosimPoliteknik Negeri Malang1
Am. MufarrihPoliteknik Negeri Malang1
Zakki Fuadi EmzainPoliteknik Negeri Malang1
Syamsul HadiPoliteknik Negeri Malang1
SarjiyanaAfiliasi tidak diketahui1
Sudarmadji .Afiliasi tidak diketahui1
Bambang IrawanLambung Mangkurat University1
Andhika Erlangga Setiawan PutraPoliteknik Negeri Malang1
Sza Sya Monica ValeriaPoliteknik Negeri Malang1
Muslimin MusliminJakarta State Polytechnic1
Samsul HadiPoliteknik Negeri Malang1
Muhamad Zidan WibowoPoliteknik Negeri Malang1
Naufal Reza PutraAfiliasi tidak diketahui1
Rico Wahyu PratamaPoliteknik Negeri Malang1
Zakiyah AmaliaPoliteknik Negeri Malang1
Tri Setyo Aji CahyonoPoliteknik Negeri Malang1
Fica Aida Nadhifatul AiniPoliteknik Negeri Malang1
Aini Zuhra Binti Abdul KadirUniversity of Technology Malaysia1
Alfarizi Al AzisPoliteknik Negeri Malang1
Vinan ViyusPoliteknik Negeri Malang1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Analysis of Leakage Test Results on Flange-Gasket Piping System Simulator Device</dc:title>
	<dc:creator>Hadi, Syamsul</dc:creator>
	<dc:creator>Hutagalung, Muhammad Naufal Abiyyi</dc:creator>
	<dc:creator>Pranoto, Bayu</dc:creator>
	<dc:creator>Dwiyanto, Firman</dc:creator>
	<dc:creator>Kurniawan, Dadang</dc:creator>
	<dc:subject xml:lang="en-US">Fluid leaks</dc:subject>
	<dc:subject xml:lang="en-US">centrifugal pumps</dc:subject>
	<dc:subject xml:lang="en-US">fluid pressure</dc:subject>
	<dc:subject xml:lang="en-US">bolt-nut tightening torque</dc:subject>
	<dc:description xml:lang="en-US">Fluid leaks in piping installations often occur in the industrial sector which is detrimental due to the selection of gasket materials, flanges, and improper tightening torque of flange bolts. The fluids that are flowed can be clean water, palm oil with a fatty acid content at an acidity level (pH) of around 4, oil, solutions with a certain pH or fuel. The purpose of the simulator device analysis is to obtain data on the level of tightening torque of bolts-nuts on 1 inch pipe flanges-gaskets and the volume of leakage. The analysis method includes setting the working pressure of the fluid on the globe valve at 1 Bar, 1.3 Bar, and 1.5 Bar on the flange-gasket piping system simulator device, measuring the lowest tightening torque at which the fluid starts to leak to the highest at a condition where there is no leak at all, and two-way Anova analysis on the distribution data. The results of the study showed that the lowest bolt-nut tightening torque at 2 Nm for three M8 bolts-nuts as flange-gasket pair locks resulted in an average fluid droplet leakage of 120 ml/hour and at a torque of 4 Nm the leakage level was about a quarter of that, namely 36 ml/hour and finally at a torque of 5 Nm there was no leakage at all. Implications in industries that use fluid flow with sufficient tightening torque of nuts-bolts on flanges-gaskets can reduce-stop losses due to leakage that occurs in their piping systems.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2025-03-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/2018</dc:identifier>
	<dc:identifier>10.31940/logic.v25i1.27-34</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 25 No. 1 (2025): March; 27-34</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v25i1</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/2018/1098</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>