Jurnal SINTA 3
Evaluation of Lathe Operating Conditions Based on ISO 10816 Using the Correlation Between Spindle Vibration and Surface Quality
Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 26 No. 2 (2026) · hlm. 95–102
- ISSN
- 2580-5649, 1412-114X
- Terbit
- 2026-07-31
- Penerbit
- Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
- Bahasa
- eng
Abstrak
The evaluation of machine tool operating conditions is commonly performed based on mechanical reliability, while its direct relationship with the quality of machined surfaces is still rarely quantified. This study aims to evaluate the operating condition of a conventional lathe based on ISO 10816 by analyzing the correlation between spindle vibration and surface roughness. Experiments were conducted on a Dixon CQ6236X1000 lathe with variations in feed rate (0.104–0.835 mm/rev) and depth of cut (0–1.5 mm) at a constant spindle speed of 460 rpm. Spindle vibration was measured in terms of root mean square (RMS) velocity (mm/s) in the vertical and horizontal directions, and frequency-domain analysis was performed using Fast Fourier Transform (FFT). Surface roughness was evaluated using Ra, Rq, and Rz parameters. The results show that the RMS vibration values range from 0.4 to 2.5 mm/s, which correspond to Zone B and Zone C of ISO 10816-3 class I. At Zone B, the surface roughness values are relatively low (Ra = 2–6 µm), indicating stable machining conditions. However, when the operating condition shifts to Zone C, the surface roughness increases significantly, with Ra values exceeding 10 µm under certain cutting conditions. The correlation analysis between RMS vibration and surface roughness yields a coefficient of determination of R² = 0.399, indicating a moderate positive relationship. FFT analysis reveals that the dominant vibration components are associated with spindle rotational frequency and its harmonics, indicating the presence of mild regenerative chatter without evidence of bearing defects.These findings demonstrate that ISO 10816 can be utilized not only as a mechanical acceptability standard but also as a predictive indicator of surface quality in turning operations. The results provide a useful reference for integrating vibration-based condition monitoring with machining quality control in both industrial and educational workshop environments.
Kata kunci
Jaringan kolaborasi para penulis
40 penulis · 119 tautan kepenulisan bersama · 39 lintas organisasi · menampilkan 40 yang paling banyak terhubung
Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.
- Politeknik Negeri Malang
- Universitas Muhammadiyah Gresik
- State University of Malang
- Universiti Teknikal Malaysia Melaka
- Politeknik Negeri Madiun
- University of Brawijaya
- Udayana University
- Organisasi lain
- Organisasi berbeda
- Organisasi sama
- Afiliasi tidak diketahui
- Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
| Rekan penulis | Organisasi | Artikel bersama |
|---|---|---|
| Fica Aida Nadhifatul Aini | Politeknik Negeri Malang | 4 |
| Fitrah Bisma Taimullah Al Jahfal | Politeknik Negeri Malang | 3 |
| Ardhi Prawira Rohim | Politeknik Negeri Malang | 3 |
| Indrazno Siradjuddin | Politeknik Negeri Malang | 2 |
| Imam Mashudi | Politeknik Negeri Malang | 2 |
| Erni Yudaningtyas | University of Brawijaya | 1 |
| Denda Dewatama | Politeknik Negeri Malang | 1 |
| Rendi Pambudi Wicaksono | Politeknik Negeri Madiun | 1 |
| Mila Fauziyah | Politeknik Negeri Malang | 1 |
| Marizan Sulaiman | Universiti Teknikal Malaysia Melaka | 1 |
| Ahmad Burhanudin Fahmi | State University of Malang | 1 |
| I Made Wirawan | State University of Malang | 1 |
| Abdul Syukor Mohamad Jaya | Universiti Teknikal Malaysia Melaka | 1 |
| Mahfud Jiono | Politeknik Negeri Malang | 1 |
| Ferdian Ronilaya | Politeknik Negeri Malang | 1 |
| Lie Jasa | Udayana University | 1 |
| Ratna Ika Putri | Politeknik Negeri Malang | 1 |
| Ika Noer Syamsiana | Politeknik Negeri Malang | 1 |
| Haris Puspito Buwono | Politeknik Negeri Malang | 1 |
| Agus Dani | Politeknik Negeri Malang | 1 |
| Muhammad Fakhruddin | Politeknik Negeri Malang | 1 |
| Nicky Suwandhy Widhi Supriyanto | Politeknik Negeri Malang | 1 |
| Syamsul Hadi | Politeknik Negeri Malang | 1 |
| Rico Wahyu Pratama | Politeknik Negeri Malang | 1 |
| Tri Setyo Aji Cahyono | Politeknik Negeri Malang | 1 |
| Aini Zuhra Binti Abdul Kadir | University of Technology Malaysia | 1 |
| Septyana Riskitasari | Politeknik Negeri Malang | 1 |
| Kris Witono | Politeknik Negeri Malang | 1 |
| Etik Puspitasari | Politeknik Negeri Malang | 1 |
| Alviani Hesthi Permata Ningtyas | Universitas Muhammadiyah Gresik | 1 |
| Ilham Arifin Pahlawan | Universitas Muhammadiyah Gresik | 1 |
| Rilo Chandra Muhamadin | Universitas Muhammadiyah Gresik | 1 |
| R.N. Akhsanu Takwim | Politeknik Negeri Malang | 1 |
| Listiono Listiono | Politeknik Negeri Malang | 1 |
Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.