Melola Discovery

← Melola Discovery

Jurnal SINTA 3

Redesign of Clove Dryer Simulation Machine Using Heat Waste of Radiator as the Heat Source

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 19 No. 1 (2019) · hlm. 7–13

DOI
10.31940/logic.v19i1.1101
ISSN
2580-5649, 1412-114X
Terbit
2019-03-30
Penerbit
Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali
Bahasa
eng

Abstrak

In this study, a redesign to a clove dryer simulation tool using exhaust heat from radiator as a source of heat energy has been done. The dryer simulation tool consists of reservoir tank, a heater, a pump to circulate the water in the system, a radiator as a heat exchanger and a drying chamber with 2 shelves. The redesign stage is carried out by fixing the piping insulation system, changing the pipe and adding valve controls to vary the velocity of the fluid flow. Variations made are variations in the mass flow rate of 0.09 kg / s and 0.18 kg /s with a constant air flow rate of 1 m/s. The results of the analysis show that at a higher mass flow rate of 0.18 kg/s the average rate of heat transfer from the radiator air side is higher, which is around 3971.65 watts. The effectiveness of the radiator will also be higher at a higher mass flow rate, the average is 0.34 at a mass flow rate of 0.09 kg/s and 0.43 at a mass flow rate of 0.18 kg /s. For drying rates with a load of 2 kg of cloves with a higher flow rate of liquid will be faster, which is about 5 hours with a flow rate of 0.18 kg/s and 6.5 hours at a flow rate of 0.09 kg/s

Jaringan kolaborasi para penulis

7 penulis · 12 tautan kepenulisan bersama · 5 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Politeknik Negeri Bali
  • Udayana University
  • Padjadjaran University
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Made Ery ArsanaPoliteknik Negeri Bali1
I Putu Adi WigunaPoliteknik Negeri Bali1
I Nyoman Artha GunawanPoliteknik Negeri Bali1
I Made JoniPadjadjaran University1
Wayan Nata SeptiadiUdayana University1
Tjokorda Gde Tirta NindhiaUdayana University1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs.pnb.ac.id/index.php/LOGIC/oai, pertama di-harvest 19 Nov 2026, terakhir terlihat 19 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Redesign of Clove Dryer Simulation Machine Using Heat Waste of Radiator as the Heat Source</dc:title>
	<dc:creator>Wiryanta, I Kadek Ervan Hadi</dc:creator>
	<dc:description xml:lang="en-US">In this study, a redesign to a clove&amp;nbsp; dryer simulation tool using&amp;nbsp; exhaust heat from radiator as a source of heat energy has been done. The dryer&amp;nbsp; simulation tool consists of reservoir tank, a heater, a pump to circulate the water in the system, a radiator as a heat exchanger and a drying chamber with 2 shelves. The redesign stage is carried out by fixing the piping insulation system, changing the pipe and adding valve controls to vary the velocity of the fluid flow. Variations made are variations in the mass flow rate of 0.09 kg / s and 0.18 kg /s with a constant air flow rate of 1 m/s. The results of the analysis show that at a higher mass flow rate of 0.18 kg/s the average rate of heat transfer from the radiator air side is higher, which is around 3971.65 watts. The effectiveness of the radiator will also be higher at a higher mass flow rate, the average is 0.34 at a mass flow rate of 0.09 kg/s and 0.43 at a mass flow rate of 0.18 kg /s. For drying rates with a load of 2 kg of cloves with a higher flow rate of liquid will be faster, which is about 5 hours with a flow rate of &amp;nbsp;0.18 kg/s and 6.5 hours at a flow rate of 0.09 kg/s</dc:description>
	<dc:publisher xml:lang="en-US">Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali</dc:publisher>
	<dc:date>2019-03-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs.pnb.ac.id/index.php/LOGIC/article/view/1101</dc:identifier>
	<dc:identifier>10.31940/logic.v19i1.1101</dc:identifier>
	<dc:source xml:lang="en-US">Logic : Jurnal Rancang Bangun dan Teknologi; Vol 19 No 1 (2019): March; 7-13</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v19i1</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs.pnb.ac.id/index.php/LOGIC/article/view/1101/982</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2019 Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
</oai_dc:dc>