Melola Discovery

← Melola Discovery

Jurnal Tanpa peringkat SINTA

ANALISIS PENGARUH VARIASI TEMPERATUR BAJA AISI 1018 TERHADAP KEKERASAN DENGAN METODE JOMINY TEST

Dinamika : Jurnal Ilmiah Teknik Mesin · Vol. 10 No. 2 (2019) · hlm. 53–58

DOI
10.33772/djitm.v10i2.6954
ISSN
2502-3373, 2085-8817
Terbit
2019-05-22
Penerbit
Jurusan Teknik Mesin, Universitas Halu Oleo
Bahasa
eng

Abstrak

Hardenability of steel is an important guide to determine the pattern of heat behavior and the nature of the material to be heat-treated in the production of components. One way to determine steel hardenability is by using Jominy test method. This study aims to determine the hardness of the AISI 1018 steel by varying temperature in heat treatment. Hardness test was conducted using the Rockwell method (HRA) by varying the heating temperature to 700 °C, 800 °C and 900 °C. The material used was AISI 1018 steel and water as a cooling medium. The standard for making specimens refers to the ASTM A 255 Jominy Test with the following dimension: length of specimen 101.6 mm x diameter of specimen 25.4 mm. Electric heating furnace was used to heat the specimen according to the desired temperature. After a 15-minute holding time, the specimen was then cooled in clean water as cooling medium using Jominy test apparatus. Each specimen was cooled by spraying clean water onto it for 10 minutes. The results showed that the maximum hardness value occurred at the end of the specimen closest to the center of the spray and that the hardness decreased as the distance from the tip of the specimen increased. The results also showed that the higher the given heating temperature, the higher the hardness value of the specimens. However, the increase in temperature does not have a significant effect. This was probably the result of improper selection of materials where the heat treatment requires that the specimen contains more than 0,3% carbon. The specimen was too long on the air when released from the furnace. Hardness of test results obtained at temperature at a heating temperature of 700 ° C the average hardness value was 48.72 kg / mm2, at a temperature heating of 800 ° C the average hardness value was 47.44 kg / mm2 and at a heating temperature of 900 ° C the average hardness value was 48.12 kg/mm2.

Kata kunci

Jaringan kolaborasi para penulis

6 penulis · 11 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Ichsan RistiawanAfiliasi tidak diketahui1
Eko DespryantoAfiliasi tidak diketahui1
Muhammad Afif ZakwanAfiliasi tidak diketahui1
William RompiAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://ojs.uho.ac.id/index.php/dinamika/oai, pertama di-harvest 31 Okt 2026, terakhir terlihat 15 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">ANALISIS PENGARUH VARIASI TEMPERATUR BAJA AISI 1018 TERHADAP KEKERASAN DENGAN METODE  JOMINY TEST</dc:title>
	<dc:creator>Harjuma, Harjuma</dc:creator>
	<dc:creator>Parekke, Simon</dc:creator>
	<dc:subject xml:lang="en-US"></dc:subject>
	<dc:subject xml:lang="en-US">Temperature, cooling, Jominy test, hardness, AISI 1018 steel</dc:subject>
	<dc:description xml:lang="en-US">Hardenability of steel is an important guide to determine the pattern of heat behavior and the nature of the material to be heat-treated in the production of components. One way to determine steel hardenability is by using Jominy test method. This study aims to determine the hardness of the AISI 1018 steel by varying temperature in heat treatment. Hardness test was conducted using the Rockwell method (HRA) by varying the heating temperature to 700 °C, 800 °C and 900 °C. The material used was AISI 1018 steel and water as a cooling medium. The standard for making specimens refers to the ASTM A 255 Jominy Test with the following dimension: length of specimen 101.6 mm x diameter of specimen 25.4 mm. Electric heating furnace was used to heat the specimen according to the desired temperature. After a 15-minute holding time, the specimen was then cooled in clean water as cooling medium using Jominy test apparatus. Each specimen was cooled by spraying clean water onto it for 10 minutes. The results showed that the maximum hardness value occurred at the end of the specimen closest to the center of the spray and that the hardness decreased as the distance from the tip of the specimen increased. The results also showed that the higher the given heating temperature, the higher the hardness value of the specimens. However, the increase in temperature does not have a significant effect. This was probably the result of improper selection of materials where the heat treatment requires that the specimen contains more than 0,3% carbon. The specimen was too long on the air when released from the furnace. Hardness of test results obtained at temperature at a heating temperature of 700 ° C the average hardness value was 48.72 kg / mm2, at a temperature heating of 800 ° C the average hardness value was 47.44 kg / mm2 and at a heating temperature of 900 ° C the average hardness value was 48.12 kg/mm2. </dc:description>
	<dc:publisher xml:lang="en-US">Jurusan Teknik Mesin, Universitas Halu Oleo</dc:publisher>
	<dc:contributor xml:lang="en-US"></dc:contributor>
	<dc:date>2019-05-22</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US"></dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs.uho.ac.id/index.php/dinamika/article/view/6954</dc:identifier>
	<dc:identifier>10.33772/djitm.v10i2.6954</dc:identifier>
	<dc:source xml:lang="en-US">Dinamika : Jurnal Ilmiah Teknik Mesin; Vol 10, No 2 (2019); 53-58</dc:source>
	<dc:source>2502-3373</dc:source>
	<dc:source>2085-8817</dc:source>
	<dc:source>10.33772/djitm.v10i2</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs.uho.ac.id/index.php/dinamika/article/view/6954/5112</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2019 DINAMIKA: Jurnal Ilmiah Teknik Mesin</dc:rights>
</oai_dc:dc>