Melola Discovery

← Melola Discovery

Akses terbuka Jurnal

Fatigue Life Analysis of Mooring Cleats on The N219A Aircraft Floater Based on Numerical Simulation

Zona Laut Jurnal Inovasi Sains Dan Teknologi Kelautan · Vol. ume (2024) · hlm. 213–222

DOI
10.62012/zl.v5i2.42798
ISSN
2721-5717, 2747-2124
Terbit
2024-07-27
Penerbit
Departemen Teknik Kelautan Universitas Hasanuddin
Bahasa
en
Lisensi
creativecommons.org/licenses/by/4.0

Abstrak

One of the procedures for rescuing a seaplane after an operational is to secure it, namely by mooring at an available port or mooring at a mooring buoy. This mooring buoy is considered a vehicle necessary for securing seaplanes in coastal conditions where it is not yet possible to build infrastructure in the form of an amphiport. To overcome this problem, seaplanes need to add a mooring cleat at the end of the bow of each float, which attaches the rope to the mooring buoy itself. So, it is necessary to study the strength of the mooring cleat itself when withstanding environmental loads. This study was carried out by modelling the mooring cleat using the finite element method to determine where the most significant stresses occur in the mooring cleat structure. Mooring cleats are modelled on deck thickness with varying thicknesses of 20mm and 40mm. The stress that occurred in the mooring cleat structure is then calculated using the Palmgren-Miner rule to determine the fatigue life of the mooring cleat for each variation. It was found that the largest von Misses stress experienced by the structure using 7075-T6 aluminium material was 147.87 MPa, which occurred in the mooring cleat, which was located on the 20mm deck thickness variation at the portside. Meanwhile, this variation's most extended fatigue life calculation occurred for the 40mm deck thickness variation on the portside with 514.43 years.

Kata kunci

Jaringan kolaborasi para penulis

25 penulis · 102 tautan kepenulisan bersama · 19 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • National Research and Innovation Agency
  • Institut Teknologi Sepuluh Nopember
  • Hasanuddin University
  • Universiti Sains Malaysia
  • UCSI University
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Endah SuwarniAfiliasi tidak diketahui2
Cakra WijayaAfiliasi tidak diketahui2
Endah SuwarniAfiliasi tidak diketahui2
Cakra WijayaAfiliasi tidak diketahui2
Habibi PalippuiHasanuddin University1
Juswan SadeHasanuddin University1
SilvianitaInstitut Teknologi Sepuluh Nopember1
Faizal SattuInstitut Teknologi Sepuluh Nopember1
Abdul GhofurNational Research and Innovation Agency1
Raj RajendranAfiliasi tidak diketahui1
Mahmud Iwan SolihinUCSI University1
Affiani MachmudahNational Research and Innovation Agency1
Elmi Abu BakarUniversiti Sains Malaysia1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://journal.unhas.ac.id/index.php/zonalaut/oai, pertama di-harvest 2 Nov 2026, terakhir terlihat 15 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Fatigue Life Analysis of Mooring Cleats on The N219A Aircraft Floater Based on Numerical Simulation</dc:title>
	<dc:creator xml:lang="en">Yulfani, Rosi Dwi</dc:creator>
	<dc:creator xml:lang="en">Rosyid, Daniel M.</dc:creator>
	<dc:creator xml:lang="en">Nugroho, Wibowo Harso</dc:creator>
	<dc:creator xml:lang="en">Priohutomo, Kusnindar</dc:creator>
	<dc:creator xml:lang="en">Sugiarto, Moh. Muria Armansyah</dc:creator>
	<dc:creator xml:lang="en">Arianti, Erdina</dc:creator>
	<dc:creator xml:lang="id">Yulfani, Rosi Dwi</dc:creator>
	<dc:creator xml:lang="id">Rosyid, Daniel M.</dc:creator>
	<dc:creator xml:lang="id">Nugroho, Wibowo Harso</dc:creator>
	<dc:creator xml:lang="id">Priohutomo, Kusnindar</dc:creator>
	<dc:creator xml:lang="id">Sugiarto, Moh. Muria Armansyah</dc:creator>
	<dc:creator xml:lang="id">Arianti, Erdina</dc:creator>
	<dc:subject xml:lang="en">Mooring Cleats</dc:subject>
	<dc:subject xml:lang="en">N219A</dc:subject>
	<dc:subject xml:lang="en">Stress</dc:subject>
	<dc:subject xml:lang="en">Palmgren-Miner</dc:subject>
	<dc:subject xml:lang="en">Fatigue Life</dc:subject>
	<dc:subject xml:lang="en">Mooring Cleats</dc:subject>
	<dc:subject xml:lang="en">N219A</dc:subject>
	<dc:subject xml:lang="en">Stress</dc:subject>
	<dc:subject xml:lang="en">Palmgren-Miner</dc:subject>
	<dc:subject xml:lang="en">Fatigue Life</dc:subject>
	<dc:description xml:lang="en">One of the procedures for rescuing a seaplane after an operational is to secure it, namely by mooring at an available port or mooring at a mooring buoy. This mooring buoy is considered a vehicle necessary for securing seaplanes in coastal conditions where it is not yet possible to build infrastructure in the form of an amphiport. To overcome this problem, seaplanes need to add a mooring cleat at the end of the bow of each float, which attaches the rope to the mooring buoy itself. So, it is necessary to study the strength of the mooring cleat itself when withstanding environmental loads. This study was carried out by modelling the mooring cleat using the finite element method to determine where the most significant stresses occur in the mooring cleat structure. Mooring cleats are modelled on deck thickness with varying thicknesses of 20mm and 40mm. The stress that occurred in the mooring cleat structure is then calculated using the Palmgren-Miner rule to determine the fatigue life of the mooring cleat for each variation. It was found that the largest von Misses stress experienced by the structure using 7075-T6 aluminium material was 147.87 MPa, which occurred in the mooring cleat, which was located on the 20mm deck thickness variation at the portside. Meanwhile, this variation's most extended fatigue life calculation occurred for the 40mm deck thickness variation on the portside with 514.43 years.</dc:description>
	<dc:publisher xml:lang="en">Departemen Teknik Kelautan Universitas Hasanuddin</dc:publisher>
	<dc:date>2024-07-27</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unhas.ac.id/index.php/zonalaut/article/view/42798</dc:identifier>
	<dc:identifier>10.62012/zl.v5i2.42798</dc:identifier>
	<dc:source xml:lang="en">Zona Laut Jurnal Inovasi Sains Dan Teknologi Kelautan; Volume 5, Number 2, July 2024 Edition; 213-222</dc:source>
	<dc:source xml:lang="id">Zona Laut : Jurnal Inovasi Sains Dan Teknologi  Kelautan; Volume 5, Number 2, July 2024 Edition; 213-222</dc:source>
	<dc:source>2721-5717</dc:source>
	<dc:source>2747-2124</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unhas.ac.id/index.php/zonalaut/article/view/42798/12458</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2025 Rosi Dwi Yulfani, Daniel M. Rosyid, Wibowo Harso Nugroho, Kusnindar Priohutomo, Moh. Muria Armansyah Sugiarto, Erdina Arianti</dc:rights>
	<dc:rights xml:lang="en">https://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>