Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

THERMO-MECHANICAL PARAMETER OPTIMIZATION VIA TAGUCHI DESIGN TO MINIMIZE OFF-MERGE DEFECTS AND ENHANCE POLYESTER FIBER UNIFORMITY

Jurnal Ilmiah Ilmu Terapan Universitas Jambi · Vol. 10 No. 4 (2026) · hlm. 2149–2161

DOI
10.22437/jiituj.v10i4.55711
ISSN
2580-2259, 2580-2240
Terbit
2026-08-31
Penerbit
LPPM Universitas Jambi
Bahasa
en
Lisensi
creativecommons.org/licenses/by/4.0

Abstrak

Defect minimization remains a critical operational challenge in continuous polyester fiber manufacturing, where off-merge defects compromise fiber crystallinity and dye uniformity, leading to material downgrading. This study aims to optimize key heat-setting operational parameters—specifically heat-setter temperature and tow speed—to reduce off-merge defect rates in industrial polyester staple fiber production. Utilizing the Taguchi Design of Experiments (L4 orthogonal array) with three replications under commercial production conditions, process parameters were evaluated through Analysis of Variance (ANOVA) and Signal-to-Noise (S/N) ratio analysis under the “smaller-the-better” criterion. Results indicated that heat-setter temperature was the dominant factor influencing defect variability (39.02% contribution, F = 10.66), followed by tow speed (21.95% contribution, F = 6.00), whereas their interaction effect was statistically insignificant (9.76%). Optimal settings were identified at 200 °C temperature and 260 m/min tow speed. Confirmatory trials validated these parameters, reducing the off-merge defect rate from 11.50% to 8.25%, resulting in a net defect reduction of 3.25%. The findings demonstrate that higher thermal energy and optimized tension enhance molecular alignment and the consistency of dye uptake. Industrially, this study provides synthetic fiber manufacturers with an evidence-based, cost-effective optimization approach that significantly reduces scrap rates, improves yield efficiency, and supports sustainable quality engineering in large-scale production environments.

Kata kunci

Jaringan kolaborasi para penulis

2 penulis · 1 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universitas Jenderal Achmad Yani
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Sumber metadata: OAI-PMH (metadata jurnal) https://online-journal.unja.ac.id/index.php/JIITUJ/oai, pertama di-harvest 5 Nov 2026, terakhir terlihat 15 Nov 2026.
Metadata asli (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">THERMO-MECHANICAL PARAMETER OPTIMIZATION VIA TAGUCHI DESIGN TO MINIMIZE OFF-MERGE DEFECTS AND ENHANCE POLYESTER FIBER UNIFORMITY</dc:title>
	<dc:creator xml:lang="en">Suryana, Hendy</dc:creator>
	<dc:creator xml:lang="en">Islam, Sifa Nurul</dc:creator>
	<dc:subject xml:lang="en">Crystallinity</dc:subject>
	<dc:subject xml:lang="en">Defect Reduction</dc:subject>
	<dc:subject xml:lang="en">Heat-Setting Process</dc:subject>
	<dc:subject xml:lang="en">Polyester Fiber</dc:subject>
	<dc:subject xml:lang="en">Quality Engineering</dc:subject>
	<dc:subject xml:lang="en">Taguchi Method</dc:subject>
	<dc:description xml:lang="en">Defect minimization remains a critical operational challenge in continuous polyester fiber manufacturing, where off-merge defects compromise fiber crystallinity and dye uniformity, leading to material downgrading. This study aims to optimize key heat-setting operational parameters—specifically heat-setter temperature and tow speed—to reduce off-merge defect rates in industrial polyester staple fiber production. Utilizing the Taguchi Design of Experiments (L4 orthogonal array) with three replications under commercial production conditions, process parameters were evaluated through Analysis of Variance (ANOVA) and Signal-to-Noise (S/N) ratio analysis under the “smaller-the-better” criterion. Results indicated that heat-setter temperature was the dominant factor influencing defect variability (39.02% contribution, F = 10.66), followed by tow speed (21.95% contribution, F = 6.00), whereas their interaction effect was statistically insignificant (9.76%). Optimal settings were identified at 200 °C temperature and 260 m/min tow speed. Confirmatory trials validated these parameters, reducing the off-merge defect rate from 11.50% to 8.25%, resulting in a net defect reduction of 3.25%. The findings demonstrate that higher thermal energy and optimized tension enhance molecular alignment and the consistency of dye uptake. Industrially, this study provides synthetic fiber manufacturers with an evidence-based, cost-effective optimization approach that significantly reduces scrap rates, improves yield efficiency, and supports sustainable quality engineering in large-scale production environments.</dc:description>
	<dc:publisher xml:lang="en">LPPM Universitas Jambi</dc:publisher>
	<dc:date>2026-08-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://online-journal.unja.ac.id/JIITUJ/article/view/55711</dc:identifier>
	<dc:identifier>10.22437/jiituj.v10i4.55711</dc:identifier>
	<dc:source xml:lang="en">Jurnal Ilmiah Ilmu Terapan Universitas Jambi; Vol. 10 No. 4 (2026): Volume 10, Nomor 4, August 2026; 2149-2161</dc:source>
	<dc:source>2580-2259</dc:source>
	<dc:source>2580-2240</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://online-journal.unja.ac.id/JIITUJ/article/view/55711/25514</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2026 Hendy Suryana, Sifa Nurul Islam</dc:rights>
	<dc:rights xml:lang="en">https://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>