Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Maximum Radiated Emissions of Printed Circuit Board Using Analytical Methods

International Journal of Electrical and Computer Engineering (IJECE) · Vol. 7 No. 6 (2019)

DOI
10.11591/ijece.v7i6.8658
ISSN
2088-8708, 2088-8708
Terbit
2019-12-01
Penerbit
Institute of Advanced Engineering and Science
Lisensi
creativecommons.org/licenses/by-nc-nd/4.0

Abstrak

The rapid progress of technology has imposed significant challenges on Printed Circuit Boards (PCB) designers. Once of those challenges is to satisfy the electromagnetic compatibility (EMC) compliance requirements. For that reason, EMC compliance must be considered earlier at the design stage for time and cost savings. Conventionally, full wave simulation is employed to check whether the designed PCB meets EMC standards or not. However, this method is not a suitable option since it requires intensive computational time and thus increasing the unit cost. This paper describes novel analytical models for estimating the radiated emissions (RE) of PCB. These models can be used to help the circuit designer to modify their circuit based on the maximum allowable RE comparing to the relevant EMC-RE standard limit. Although there are many RE sources on PCB, this paper focuses on the significant source of RE on PCB; namely PCB-traces. The trace geometry, termination impedance, dielectric type, etc. can be specified based on the maximum allowable emissions. The proposed models were verified by comparing the results of the proposed models with both simulation and experimental results. Good agreements were obtained between the analytically computed results and simulation/measurement results with accuracy of ±3dB.

Jaringan kolaborasi para penulis

11 penulis · 24 tautan kepenulisan bersama

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Tun Hussein Onn University of Malaysia
  • Afiliasi tidak diketahui
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Jawad AliTun Hussein Onn University of Malaysia1
Roshayati YahyaTun Hussein Onn University of Malaysia1
Noorsaliza AbdullahTun Hussein Onn University of Malaysia1
Warsuzarina Mat JubadiTun Hussein Onn University of Malaysia1
Prabakaran A L KalaihrasanTun Hussein Onn University of Malaysia1
Nurfarina ZainalTun Hussein Onn University of Malaysia1
Nor Hafizah NgajikinTun Hussein Onn University of Malaysia1
Hing Wah LeeAfiliasi tidak diketahui1

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Data ini berasal dari Crossref (yang disetorkan penerbit), karena endpoint OAI-PMH milik jurnal tidak dapat di-harvest.

Sumber metadata: Crossref API (cadangan, berdasarkan ISSN) https://api.crossref.org/journals/2088-8708/works, pertama di-harvest 27 Okt 2026, terakhir terlihat 15 Nov 2026.
Metadata sebagai oai_dc, dikonversi dari Crossref
<oai_dc:dc xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/"><dc:title>Maximum Radiated Emissions of Printed Circuit Board Using Analytical Methods</dc:title><dc:creator>Jenu, Mohd Zarar Mohd</dc:creator><dc:creator>Sayegh, Ahmed M.</dc:creator><dc:creator>Sapuan, Syarfa Zahirah</dc:creator><dc:description>&lt;jats:p&gt;&amp;lt;span&amp;gt;The rapid progress of technology has imposed significant challenges on Printed Circuit Boards (PCB) designers. Once of those challenges is to satisfy the electromagnetic compatibility (EMC) compliance requirements. For that reason, EMC compliance must be considered earlier at the design stage for time and cost savings. Conventionally, full wave simulation is employed to check whether the designed PCB meets EMC standards or not. However, this method is not a suitable option since it requires intensive computational time and thus increasing the unit cost. This paper describes novel analytical models for estimating the radiated emissions (RE) of PCB. These models can be used to help the circuit designer to modify their circuit based on the maximum allowable RE comparing to the relevant EMC-RE standard limit. Although there are many RE sources on PCB, this paper focuses on the significant source of RE on PCB; namely PCB-traces. The trace geometry, termination impedance, dielectric type, etc. can be specified based on the maximum allowable emissions. The proposed models were verified by comparing the results of the proposed models with both simulation and experimental results. Good agreements were obtained between the analytically computed results and simulation/measurement results with accuracy of ±3dB.&amp;lt;/span&amp;gt;&lt;/jats:p&gt;</dc:description><dc:publisher>Institute of Advanced Engineering and Science</dc:publisher><dc:date>2019-12-01</dc:date><dc:type>info:eu-repo/semantics/article</dc:type><dc:format>application/pdf</dc:format><dc:identifier>https://doi.org/10.11591/ijece.v7i6.8658</dc:identifier><dc:identifier>10.11591/ijece.v7i6.8658</dc:identifier><dc:source>International Journal of Electrical and Computer Engineering (IJECE); Vol 7 No 6 (2019); 2919</dc:source><dc:source>2088-8708</dc:source><dc:source>2088-8708</dc:source><dc:relation>http://iaescore.com/journals/index.php/IJECE/article/viewFile/8658/7443</dc:relation><dc:rights>http://creativecommons.org/licenses/by-nc-nd/4.0</dc:rights></oai_dc:dc>