Melola Discovery

← Melola Discovery

Akses terbuka Jurnal SINTA 1

Analysis of the range of acceleration for an accelerometer with extended beams

International Journal of Electrical and Computer Engineering (IJECE) · Vol. 6 No. 4 (2016)

DOI
10.11591/ijece.v6i4.pp1541-1550
ISSN
2088-8708, 2088-8708
Terbit
2016-08-01
Penerbit
Institute of Advanced Engineering and Science
Lisensi
creativecommons.org/licenses/by-nc/4.0

Abstrak

The elastic behaviour of a system can be determined by an analysis of stresses. The stress generated in the element loaded of an accelerometer is of interest here. In these devices, the suspension beams are the elements subjected to greater stresses, as they support the mass. The stress that they can support is limited by the elastic limit of the material. Based on this analysis, the operating conditions to prevent permanent deformations are determined. The analysis is focused on the acceleration applied to the accelerometer because this parameter increases considerably the stresses in the device. A relationship between normal stress and gravity applied is obtained. This equation is used in order to avoid exceeding the elastic limit, during the accelerometer operation. This fact determines the acceleration range supported by the device. In the literature, studies about the physics and modelling of accelerometers are performed. However, about the specific acceleration of operation which they are subjected, information about its determination is not provided. In this paper, the analysis is realized considering a Conventional Capacitive Accelerometer (CCA) and a Capacitive Accelerometer with Extended Beams (CAEB), particularly, on the normal stress. When a range of acceleration values are applied, normal stress occur which must not exceed the elastic limit of the material, as it was mentioned before. The Matlab code used to calculate this relationship is given in Appendix A.

Jaringan kolaborasi para penulis

9 penulis · 29 tautan kepenulisan bersama · 7 lintas organisasi

Arahkan kursor atau ketuk sebuah nama untuk menyorot rekan penulisnya. Klik dua kali untuk membuka halaman penulis.

  • Universidad Autónoma del Estado de Morelos
  • National Institute of Astrophysics, Optics and Electronics
  • Organisasi berbeda
  • Organisasi sama
  • Afiliasi tidak diketahui
  • Garis lebih tebal = lebih banyak artikel bersama · lingkaran lebih besar = lebih banyak artikel
Tampilkan sebagai tabel
Rekan penulisOrganisasiArtikel bersama
Ramón Cabello-RuizUniversidad Autónoma del Estado de Morelos12
Volodymyr V GrimalskyUniversidad Autónoma del Estado de Morelos4
Alejandra Ocampo-DiazUniversidad Autónoma del Estado de Morelos3

Afiliasi berasal dari OpenAlex; metadata OAI-PMH jurnal tidak memuatnya. Penulis tanpa ID OpenAlex dicocokkan berdasarkan nama, sehingga dua orang bisa tergabung atau satu orang bisa terpisah.

Data ini berasal dari Crossref (yang disetorkan penerbit), karena endpoint OAI-PMH milik jurnal tidak dapat di-harvest.

Sumber metadata: Crossref API (cadangan, berdasarkan ISSN) https://api.crossref.org/journals/2088-8708/works, pertama di-harvest 27 Okt 2026, terakhir terlihat 15 Nov 2026.
Metadata sebagai oai_dc, dikonversi dari Crossref
<oai_dc:dc xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/"><dc:title>Analysis of the range of acceleration for an accelerometer with extended beams</dc:title><dc:creator>Cabello, Ramon</dc:creator><dc:creator>Tecpoyotl, Margarita</dc:creator><dc:creator>Vera, Jose Gerardo</dc:creator><dc:creator>Torres, Alfonso</dc:creator><dc:creator>Vargas, Pedro</dc:creator><dc:creator>Koshevaya, Svetlana</dc:creator><dc:description>&lt;jats:p&gt;&amp;lt;span lang="EN-US"&amp;gt;The elastic behaviour of a system can be determined by an analysis of stresses. The stress generated in the element loaded of an accelerometer is of interest here. In these devices, the suspension beams are the elements subjected to greater stresses, as they support the mass. The stress that they can support is limited by the elastic limit of the material. Based on this analysis, the operating conditions to prevent permanent deformations are determined. The analysis is focused on the acceleration applied to the accelerometer because this parameter increases considerably the stresses in the device. A relationship between normal stress and gravity applied is obtained. This equation is used in order to avoid exceeding the elastic limit, during the accelerometer operation. This fact determines the acceleration range supported by the device. In the literature, studies about the physics and modelling of accelerometers are performed. However, about the specific acceleration of operation which they are subjected, information about its determination is not provided. In this paper, the analysis is realized considering a Conventional Capacitive Accelerometer (CCA) and a Capacitive Accelerometer with Extended Beams (CAEB), particularly, on the normal stress. When a range of acceleration values are applied, normal stress occur which must not exceed the elastic limit of the material, as it was mentioned before. The Matlab code used to calculate this relationship is given in Appendix A.&amp;lt;/span&amp;gt;&lt;/jats:p&gt;</dc:description><dc:publisher>Institute of Advanced Engineering and Science</dc:publisher><dc:date>2016-08-01</dc:date><dc:type>info:eu-repo/semantics/article</dc:type><dc:format>application/pdf</dc:format><dc:identifier>https://doi.org/10.11591/ijece.v6i4.pp1541-1550</dc:identifier><dc:identifier>10.11591/ijece.v6i4.pp1541-1550</dc:identifier><dc:source>International Journal of Electrical and Computer Engineering (IJECE); Vol 6 No 4 (2016); 1541</dc:source><dc:source>2088-8708</dc:source><dc:source>2088-8708</dc:source><dc:relation>http://ijece.iaescore.com/index.php/IJECE/article/viewFile/721/479</dc:relation><dc:rights>http://creativecommons.org/licenses/by-nc/4.0</dc:rights></oai_dc:dc>