Melola Discovery

← Melola Discovery

Open access Journal SINTA 1

FIXATION PROCESS OF LAMINATED BAMBOO COMPRESSION FROM CURVED CROSS-SECTION SLATS

Indonesian Journal of Forestry Research · Vol. 8 No. 2 (2021) · pp. 159–171

DOI
10.59465/ijfr.2021.8.2.159-171
ISSN
2406-8195, 2355-7079
Published
2021-10-31
Publisher
Association of Indonesian Forestry and Environment Researchers and Technicians
Language
eng
License
creativecommons.org/licenses/by-nc-sa/4.0/

Abstract

Removing the outer part of bamboo for manufacturing flat bamboo lamination has disadvantage on the density of the product. The purpose of this experiment was to investigate the fixation of compressed bamboo from curved cross-section slats. The compression of bamboo slats using densification technique was aimed for uniform density. Furthermore, steam treatments were conducted to fix the deformation. The compressed bamboo slats revealed that the density of the samples at the bottom parts increased from 0.4–0.56 g/cm3 to 0.89–1.05 g/cm3 after pressing with a compression level between 46.98–63.97%, while the samples in the middle parts increased from 0.7–0.83 g/cm3 to 1.02–1.18 g/cm3 with the compression level of 32.92–41.5%. These results were slightly higher than that of the upper parts, which was between 0.91–0.98 g/cm3. The recovery of set decreased and the weight loss increased with increasing temperature and steam treatment time. Fixation of compressive deformation could be achieved at 160°C within 60 minutes. The bottom parts of samples experienced a slightly greater weight loss compared to the middle parts, i.e. 8.38% and 7.49%, respectively. The anatomical structure of bamboo tended to deform during densification process. Furthermore, the steam treatments affected the colour of densified bamboo which became darker. From this experiment, it can be concluded that the manufacture of laminated bamboo from bamboo slats can be uniformed in strength by equalizing the density at the bottom and middle with the upper parts through the densification technique.

Keywords

Collaboration network of the authors

40 authors · 236 co-authorship links · 128 across different organisations · showing the 40 most connected

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • National Research and Innovation Agency
  • Indonesian Institute of Sciences
  • IPB University
  • Lambung Mangkurat University
  • Tanjungpura University
  • Kyoto University
  • Ministry of Industry of the Republic of Indonesia
  • Other organisations
  • Affiliation unknown
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
Ratih DamayantiNational Research and Innovation Agency13
Yusup AminIndonesian Institute of Sciences13
Dimas TriwibowoNational Research and Innovation Agency11
Prabu Satria SejatiIndonesian Institute of Sciences8
NartoNational Research and Innovation Agency7
Sari Delviana MarbunTanjungpura University6
Sarah AugustinaNational Research and Innovation Agency6
DjarwantoNational Research and Innovation Agency5
Listya Mustika DewiNational Research and Innovation Agency5
Raden Gunawan Hadi RahmantoNational Research and Innovation Agency5
Dyah Ayu AgustiningrumNational Research and Innovation Agency5
Rohmah PariNational Research and Innovation Agency5
Imran Arra’d SofiantoNational Research and Innovation Agency5
Dwi Ajias PramasariNational Research and Innovation Agency4
Widya FatriasariAffiliation unknown4
Ika WahyuniIndonesian Institute of Sciences4
Sung‐Wook HwangKyoto University2
Hairi CiptaUniversitas Gadjah Mada2
Junji SugiyamaKyoto University2
Syahrul RamadhanMinistry of Industry of the Republic of Indonesia2
Ari HardiantoPadjadjaran University2
Maya IsmayatiNational Research and Innovation Agency2
Nadia Nuraniya KamaluddinPadjadjaran University2
Nyndia Tri MuliawatiNational Research and Innovation Agency2
Narita Ayu Putri PramestiMinistry of Industry of the Republic of Indonesia2
Muh Yusram MassijayaAffiliation unknown1
Yusuf Sudo HadiIPB University1
Dina SetyawatiTanjungpura University1
Sucahyo SadiyoIPB University1
Surjono SurjokusumoAffiliation unknown1
Imam WahyudiNational Research and Innovation Agency1
SunardiAffiliation unknown1
Wiwin Tyas IstikowatiLambung Mangkurat University1
Budi SutiyaLambung Mangkurat University1
Purnama LestariLambung Mangkurat University1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) https://ejournal.aptklhi.org/index.php/ijfr/oai, first harvested 8 Nov 2026, last seen 16 Nov 2026.
Original metadata (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">FIXATION PROCESS OF LAMINATED BAMBOO COMPRESSION FROM CURVED CROSS-SECTION SLATS </dc:title>
	<dc:creator>Darmawan, Teguh</dc:creator>
	<dc:creator>Bahanawan, Adik</dc:creator>
	<dc:creator>S. Adi, Danang</dc:creator>
	<dc:creator>Dwianto, Wahyu</dc:creator>
	<dc:creator>Nugroho, Naresworo</dc:creator>
	<dc:subject xml:lang="en-US">Laminated bamboo</dc:subject>
	<dc:subject xml:lang="en-US">curved cross-section slats</dc:subject>
	<dc:subject xml:lang="en-US">fixation process</dc:subject>
	<dc:subject xml:lang="en-US">steam treatment</dc:subject>
	<dc:description xml:lang="en-US">Removing the outer part of bamboo for manufacturing flat bamboo lamination has disadvantage on the density of the product. The purpose of this experiment was to investigate the fixation of compressed bamboo from curved cross-section slats. The compression of bamboo slats using densification technique was aimed for uniform density. Furthermore, steam treatments were conducted to fix the deformation. The compressed bamboo slats revealed that the density of the samples at the bottom parts increased from 0.4–0.56 g/cm3 to 0.89–1.05 g/cm3 after pressing with a compression level between 46.98–63.97%, while the samples in the middle parts increased from 0.7–0.83 g/cm3 to 1.02–1.18 g/cm3 with the compression level of 32.92–41.5%. These results were slightly higher than that of the upper parts, which was between 0.91–0.98 g/cm3. The recovery of set decreased and the weight loss increased with increasing temperature and steam treatment time. Fixation of compressive deformation could be achieved at 160°C within 60 minutes. The bottom parts of samples experienced a slightly greater weight loss compared to the middle parts, i.e. 8.38% and 7.49%, respectively. The anatomical structure of bamboo tended to deform during densification process. Furthermore, the steam treatments affected the colour of densified bamboo which became darker. From this experiment, it can be concluded that the manufacture of laminated bamboo from bamboo slats can be uniformed in strength by equalizing the density at the bottom and middle with the upper parts through the densification technique.</dc:description>
	<dc:publisher xml:lang="en-US">Association of Indonesian Forestry and Environment Researchers and Technicians</dc:publisher>
	<dc:date>2021-10-31</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ejournal.aptklhi.org/index.php/ijfr/article/view/424</dc:identifier>
	<dc:identifier>10.59465/ijfr.2021.8.2.159-171</dc:identifier>
	<dc:source xml:lang="en-US">Indonesian Journal of Forestry Research; Vol. 8 No. 2 (2021): Indonesian Journal of Forestry Research; 159-171</dc:source>
	<dc:source>2406-8195</dc:source>
	<dc:source>2355-7079</dc:source>
	<dc:source>10.59465/ijfr.2021.8.2</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ejournal.aptklhi.org/index.php/ijfr/article/view/424/94</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2021 Indonesian Journal of Forestry Research</dc:rights>
	<dc:rights xml:lang="en-US">http://creativecommons.org/licenses/by-nc-sa/4.0/</dc:rights>
</oai_dc:dc>