Melola Discovery

← Melola Discovery

Open access Journal SINTA 1

Development of a hydraulic jack system bending tool for improved manufacturing efficiency

International Journal of Advances in Applied Sciences · Vol. 14 No. 4 (2025) · pp. 1072–1082

DOI
10.11591/ijaas.v14.i4.pp1072-1082
ISSN
2722-2594, 2252-8814
Published
2025-12-01
Publisher
Institute of Advanced Engineering and Science
Language
eng
License
creativecommons.org/licenses/by-sa/4.0

Abstract

This article presents the design, fabrication, and testing of a hydraulic sheet metal bending tool. The main objective was to create a tool capable of bending sheets of various thicknesses, ranging from 2 to 4 mm, with high precision and minimal operator effort. The design incorporates a hydraulic ram for easy operation, allowing multiple plates to be bent in a short period of time. Key calculations, including bending force, spring load, and hydraulic force, are performed to ensure the efficiency and safety of the tool. Experimental results show that the tool is able to achieve the desired bending angles, with minimal spring return, and can handle up to three 10 cm wide sheets in approximately 10 minutes. The performance of the tool has been proven by tests, and the results confirm that it can meet the requirements of industrial sheet metal bending. Based on these results, the tool demonstrates its effectiveness in small and medium-scale operations, providing a cost-effective solution for sheet metal production.

Collaboration network of the authors

18 authors · 50 co-authorship links · 8 across different organisations

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • Politeknik Negeri Ujung Pandang
  • University of Technology Malaysia
  • State University of Makassar
  • Affiliation unknown
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
Muhammad IswarAffiliation unknown3
Muhira Dzar FarabyPoliteknik Negeri Ujung Pandang2
Syahrisal SyahrisalAffiliation unknown2
Mohd Wazir MustafaUniversity of Technology Malaysia1
Makmur SainiPoliteknik Negeri Ujung Pandang1
Abdullah Asuhaimi Mohd ZinUniversity of Technology Malaysia1
A. R. SultanPoliteknik Negeri Ujung Pandang1
Arthur Halik RazakAffiliation unknown1
Yosrihard BasonganAffiliation unknown1
Asrul HidayatAffiliation unknown1
Mukhlisin MukhlisinState University of Makassar1
Mahadir SirmanAffiliation unknown1
Henny PasandangAffiliation unknown1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) http://ijaas.iaescore.com/index.php/IJAAS/oai, first harvested 8 Nov 2026, last seen 8 Nov 2026.
Original metadata (oai_dc) 
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Development of a hydraulic jack system bending tool for improved manufacturing efficiency</dc:title>
	<dc:creator>Suyuti, Muhammad Arsyad</dc:creator>
	<dc:creator>Nur, Rusdi</dc:creator>
	<dc:creator>Muttaqin, Ahmad Nurul</dc:creator>
	<dc:creator>Arminas, Arminas</dc:creator>
	<dc:creator>Sudirman, Zainal</dc:creator>
	<dc:description xml:lang="en-US">This article presents the design, fabrication, and testing of a hydraulic sheet metal bending tool. The main objective was to create a tool capable of bending sheets of various thicknesses, ranging from 2 to 4 mm, with high precision and minimal operator effort. The design incorporates a hydraulic ram for easy operation, allowing multiple plates to be bent in a short period of time. Key calculations, including bending force, spring load, and hydraulic force, are performed to ensure the efficiency and safety of the tool. Experimental results show that the tool is able to achieve the desired bending angles, with minimal spring return, and can handle up to three 10 cm wide sheets in approximately 10 minutes. The performance of the tool has been proven by tests, and the results confirm that it can meet the requirements of industrial sheet metal bending. Based on these results, the tool demonstrates its effectiveness in small and medium-scale operations, providing a cost-effective solution for sheet metal production.</dc:description>
	<dc:publisher xml:lang="en-US">Institute of Advanced Engineering and Science</dc:publisher>
	<dc:contributor xml:lang="en-US"></dc:contributor>
	<dc:date>2025-12-01</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en-US"></dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ijaas.iaescore.com/index.php/IJAAS/article/view/21779</dc:identifier>
	<dc:identifier>10.11591/ijaas.v14.i4.pp1072-1082</dc:identifier>
	<dc:source xml:lang="en-US">International Journal of Advances in Applied Sciences; Vol 14, No 4: December 2025; 1072-1082</dc:source>
	<dc:source>2722-2594</dc:source>
	<dc:source>2252-8814</dc:source>
	<dc:source>10.11591/ijaas.v14.i4</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ijaas.iaescore.com/index.php/IJAAS/article/view/21779/13345</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025 Muhammad Arsyad Suyuti, Rusdi Nur, Ahmad Nurul Muttaqin, Arminas Arminas, Zainal Sudirman</dc:rights>
	<dc:rights xml:lang="en-US">http://creativecommons.org/licenses/by-sa/4.0</dc:rights>
</oai_dc:dc>