Melola Discovery

← Melola Discovery

Journal SINTA 3

Tensile Strength Analysis of AISI 1045 Steel Results of Smaw Welding Using Variations of Preheat and Cooling Media

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 22 No. 3 (2022) · pp. 214–224

DOI
10.31940/logic.v22i3.214-224
ISSN
2580-5649, 1412-114X
Published
2022-11-30
Publisher
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Language
eng

Abstract

In the welding process, there are many factors that need to be considered, including heat input, cooling rate, the material being welded, and the use of added materials, if these factors are not considered, they can cause cracks in the American Iron & Steel Institute (AISI) 1045 material. to determine the effect of preheat variations on tensile strength, the effect of cooling media on tensile strength, and to determine the interaction of preheat variations and cooling media on tensile strength. This research method used experimentally by varying the preheat temperature 250⁰C, 325⁰C, 400⁰C, and the cooling medium was lime, sand, and normal air, then tensile test was carried out. The results showed that the cooling medium affected the tensile strength with the highest tensile strength of 64.35 kg/mm2 on the sand cooling medium, while the preheat variation had no effect on the tensile strength as shown by a graph close to the horizontal straight at the tensile strength ranging from 60 kg/mm2, interaction between preheat and cooling medium has no effect on tensile strength. This is indicated by the tensile strength values ​​that are almost close to each preheat point, namely at a temperature of 250⁰C between 53-67 kg/mm2, at 325⁰C between 56-60 kg/mm2, and a temperature of 400⁰C between 51-64 kg/mm2. In this study it can be concluded that a good cooling medium uses sand media with a preheat temperature of 250⁰C.

Keywords

Collaboration network of the authors

15 authors · 33 co-authorship links

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • Politeknik Negeri Malang
  • Affiliation unknown
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
R.N. Akhsanu TakwimPoliteknik Negeri Malang3
PurwokoAffiliation unknown2
Anggit MurdaniPoliteknik Negeri Malang2
Syamsul HadiPoliteknik Negeri Malang2
SarjiyanaAffiliation unknown2
Radhi Nurvian AmrullahPoliteknik Negeri Malang1
Naufal Reza PutraAffiliation unknown1
Syamsul HadiPoliteknik Negeri Malang1
Muhammad Naufal Abiyyi HutagalungPoliteknik Negeri Malang1
Firman DwiyantoPoliteknik Negeri Malang1
Dadang KurniawanPoliteknik Negeri Malang1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, first harvested 19 Nov 2026, last seen 19 Nov 2026.
Original metadata (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Tensile Strength Analysis of AISI 1045 Steel Results of Smaw Welding Using Variations of Preheat and Cooling Media</dc:title>
	<dc:creator>Pranoto, Bayu</dc:creator>
	<dc:creator>Subagiyo</dc:creator>
	<dc:creator>Samsul Hadi</dc:creator>
	<dc:creator>Muhamad Zidan Wibowo </dc:creator>
	<dc:subject xml:lang="en-US">Tensile Strength</dc:subject>
	<dc:subject xml:lang="en-US">Cooling Media</dc:subject>
	<dc:subject xml:lang="en-US">Welding</dc:subject>
	<dc:subject xml:lang="en-US">Preheat</dc:subject>
	<dc:subject xml:lang="en-US">SMAW</dc:subject>
	<dc:description xml:lang="en-US">In the welding process, there are many factors that need to be considered, including heat input, cooling rate, the material being welded, and the use of added materials, if these factors are not considered, they can cause cracks in the American Iron &amp;amp; Steel Institute (AISI) 1045 material. to determine the effect of preheat variations on tensile strength, the effect of cooling media on tensile strength, and to determine the interaction of preheat variations and cooling media on tensile strength. This research method used experimentally by varying the preheat temperature 250⁰C, 325⁰C, 400⁰C, and the cooling medium was lime, sand,&amp;nbsp;and normal air, then tensile test was carried out. The results showed that the cooling medium affected the tensile strength with the highest tensile strength of 64.35 kg/mm2 on the sand cooling medium, while the preheat variation had no effect on the tensile strength as shown by a graph close to the horizontal straight at the tensile strength ranging from 60 kg/mm2, interaction between preheat and cooling medium has no effect on tensile strength. This is indicated by the tensile strength values ​​that are almost close to each preheat point, namely at a temperature of 250⁰C between 53-67 kg/mm2, at 325⁰C between 56-60 kg/mm2, and a temperature of 400⁰C between 51-64 kg/mm2. In this study it can be concluded that a good cooling medium uses sand media with a preheat temperature of 250⁰C.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2022-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/520</dc:identifier>
	<dc:identifier>10.31940/logic.v22i3.214-224</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 22 No. 3 (2022): November; 214-224</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v22i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/520/403</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2022  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>