Melola Discovery

← Melola Discovery

Journal SINTA 3

Optimization of Pineapple Leaf Fiber-Reinforced ABS Waste Filaments for FDM: Effect of Mesh Size and Volume Fraction

Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 25 No. 3 (2025) · pp. 169–174

DOI
10.31940/logic.v25i3.169-174
ISSN
2580-5649, 1412-114X
Published
2025-11-30
Publisher
Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
Language
eng

Abstract

Acrylonitrile Butadiene Styrene (ABS) plastic waste presents significant potential for upcycling into environmentally friendly materials, particularly as feedstock for 3D printing filaments in Fused Deposition Modeling (FDM). This study investigates the influence of pineapple leaf fiber (PALF) reinforcement at two weight fractions (3% and 5%) and two mesh sizes (200 and 300) on the dimensional stability, printability, and mechanical properties of ABS waste-based composite filaments. Comprehensive evaluations were conducted, including filament diameter consistency, surface morphology, and uniaxial tensile testing. The 5% fiber content with 300-mesh PALF yielded the most stable filament diameter (average 1.73 mm, CV 2%), while the same formulation also achieved the highest ultimate tensile strength (UTS) of 8.873 MPa and elongation at break of 0.197%. Interestingly, the highest Young’s modulus (0.139 GPa) was observed in the 3%–300 mesh variant, although it exhibited more brittle behavior. Overall, the 5%–300 mesh formulation was identified as optimal, striking a favorable balance between tensile strength, flexibility, and dimensional consistency, thereby validating its suitability as a sustainable FDM filament derived from post-consumer ABS waste.

Keywords

Collaboration network of the authors

28 authors · 78 co-authorship links · 16 across different organisations

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • Sumatera Institute of Technology
  • Politeknik Negeri Bali
  • Bandung Institute of Technology
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
Komang Widhi WidanthaPoliteknik Negeri Bali5
I Wayan Padma Yogi AsanaPoliteknik Negeri Bali3
Sena MaulanaSumatera Institute of Technology2
Rio Ardiansyah MurdaSumatera Institute of Technology2
Fajar Aditya JulyatmojoSumatera Institute of Technology2
Astri Aulia SuwandaSumatera Institute of Technology2
Muhammad Saeful FadlanSumatera Institute of Technology2
Anisa FitriSumatera Institute of Technology2
Abdul MuhyiSumatera Institute of Technology1
Muhamad F. ArifSumatera Institute of Technology1
Kardo RajagukgukSumatera Institute of Technology1
Riyan FerdiyantoSumatera Institute of Technology1
I Wayan Suma WibawaPoliteknik Negeri Bali1
I Komang KantunPoliteknik Negeri Bali1
I Ketut SuhermanPoliteknik Negeri Bali1
I Wayan SuiryaPoliteknik Negeri Bali1
M KusumaPoliteknik Negeri Bali1
I Putu Gede Sopan RahtikaPoliteknik Negeri Bali1
Amadeus RenaldyPoliteknik Negeri Bali1
Bayu PrasetyaSumatera Institute of Technology1
Muhammad Yasin SiregarSumatera Institute of Technology1
Ahmad Andryan PrakosoSumatera Institute of Technology1
Ni Luh Wisma Eka YantiBandung Institute of Technology1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) https://ojs2.pnb.ac.id/index.php/LOGIC/oai, first harvested 19 Nov 2026, last seen 19 Nov 2026.
Original metadata (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en-US">Optimization of Pineapple Leaf Fiber-Reinforced ABS Waste Filaments for FDM: Effect of Mesh Size and Volume Fraction</dc:title>
	<dc:creator>Sipahutar, Wahyu</dc:creator>
	<dc:creator>Fikri, Azizul</dc:creator>
	<dc:creator>Baiti, Risa Nurin </dc:creator>
	<dc:creator>Siregar, Mhd Yasin </dc:creator>
	<dc:creator>Putri, Faiza Armalia </dc:creator>
	<dc:subject xml:lang="en-US">FDM</dc:subject>
	<dc:subject xml:lang="en-US">Acrylonitrile Butadiene Styrene (ABS)</dc:subject>
	<dc:subject xml:lang="en-US">Pineapple Fiber</dc:subject>
	<dc:subject xml:lang="en-US">Composite</dc:subject>
	<dc:description xml:lang="en-US">Acrylonitrile Butadiene Styrene (ABS) plastic waste presents significant potential for upcycling into environmentally friendly materials, particularly as feedstock for 3D printing filaments in Fused Deposition Modeling (FDM). This study investigates the influence of pineapple leaf fiber (PALF) reinforcement at two weight fractions (3% and 5%) and two mesh sizes (200 and 300) on the dimensional stability, printability, and mechanical properties of ABS waste-based composite filaments. Comprehensive evaluations were conducted, including filament diameter consistency, surface morphology, and uniaxial tensile testing. The 5% fiber content with 300-mesh PALF yielded the most stable filament diameter (average 1.73 mm, CV 2%), while the same formulation also achieved the highest ultimate tensile strength (UTS) of 8.873 MPa and elongation at break of 0.197%. Interestingly, the highest Young’s modulus (0.139 GPa) was observed in the 3%–300 mesh variant, although it exhibited more brittle behavior. Overall, the 5%–300 mesh formulation was identified as optimal, striking a favorable balance between tensile strength, flexibility, and dimensional consistency, thereby validating its suitability as a sustainable FDM filament derived from post-consumer ABS waste.</dc:description>
	<dc:publisher xml:lang="en-US">Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali</dc:publisher>
	<dc:date>2025-11-30</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/2686</dc:identifier>
	<dc:identifier>10.31940/logic.v25i3.169-174</dc:identifier>
	<dc:source xml:lang="en-US"> Logic : Jurnal Rancang Bangun dan Teknologi; Vol. 25 No. 3 (2025): November; 169-174</dc:source>
	<dc:source>2580-5649</dc:source>
	<dc:source>1412-114X</dc:source>
	<dc:source>10.31940/logic.v25i3</dc:source>
	<dc:language>eng</dc:language>
	<dc:relation>https://ojs2.pnb.ac.id/index.php/LOGIC/article/view/2686/1232</dc:relation>
	<dc:rights xml:lang="en-US">Copyright (c) 2025  Logic : Jurnal Rancang Bangun dan Teknologi</dc:rights>
	<dc:rights xml:lang="en-US">https://scholar.google.co.id/citations?user=smBuD3gAAAAJ&amp;hl=id</dc:rights>
</oai_dc:dc>