Journal SINTA 3
A Review Study of Influencing Factors and Conceptual Scaling Framework for Spray Drying Assisted by Ultrasonic Vibrating Mesh Atomizers
Logic: Jurnal Rancang Bangun dan Teknologi · Vol. 26 No. 2 (2026) · pp. 133–147
- ISSN
- 2580-5649, 1412-114X
- Published
- 2026-07-31
- Publisher
- Unit Publikasi Ilmiah, P3M, Politeknik Negeri Bali
- Language
- eng
Abstract
Abstract. Spray drying is widely used in the pharmaceutical, food, and chemical industries for converting liquid feed into dry particulate products. However, conventional spray drying systems commonly generate broad droplet size distributions and exhibit limited capability for producing submicron particles. To overcome these limitations, ultrasonic vibrating mesh atomizers have recently attracted significant attention due to their ability to generate highly uniform droplets with relatively low energy consumption and improved atomization controllability. Previous studies have investigated the influence of individual operating parameters on ultrasonic spray drying performance, particularly using laboratory-scale systems such as the Büchi Nano Spray Dryer B-90. Nevertheless, existing literature remains fragmented, with limited efforts to systematically establish the relative importance of governing parameters or to develop a unified conceptual framework for scaling ultrasonic spray drying systems from laboratory to industrial applications. This study addresses this gap by conducting a systematic literature-based parametric analysis of spray drying systems assisted by piezoelectric vibrating mesh atomizers. Experimental studies employing the Büchi Nano Spray Dryer B-90 were critically reviewed to identify the dominant factors controlling droplet formation, atomization stability, and particle generation behaviour. The analysed parameters were classified into three principal categories: atomization parameters, fluid properties, and drying process parameters. The analysis demonstrates that mesh aperture size, ultrasonic vibration frequency, and spray throughput are the primary parameters governing droplet formation and particle size distribution. Fluid properties, including viscosity, surface tension, and feed concentration, strongly influence atomization stability through their effects on dimensionless parameters such as the Weber number and Ohnesorge number. In contrast, drying parameters, including inlet air temperature and gas flow rate, predominantly affect evaporation kinetics and particle morphology rather than the initial droplet generation process. The reviewed studies further indicate that ultrasonic atomization commonly operates within a regime characterized by moderate Weber numbers and relatively low Ohnesorge numbers, consistent with capillary wave breakup mechanisms. Based on these findings, a conceptual scaling framework is proposed in which atomization similarity, fluid dynamic similarity, and drying conditions must be simultaneously considered to achieve reliable scale-up of ultrasonic spray drying systems
Keywords
Collaboration network of the authors
34 authors · 113 co-authorship links · 13 across different organisations
Hover or tap a name to highlight its co-authors. Double-click to open the author's page.
- Politeknik Negeri Bali
- Udayana University
- University of Indonesia
- National Nuclear Energy Agency of Indonesia
- Padjadjaran University
- Affiliation unknown
- Different organisations
- Same organisation
- Affiliation unknown
- Thicker line = more joint articles · bigger circle = more articles
Show as table
| Co-author | Organisation | Joint articles |
|---|---|---|
| I Wayan Adi Subagia | Politeknik Negeri Bali | 3 |
| Putu Wijaya Sunu | Politeknik Negeri Bali | 3 |
| Made Ery Arsana | Politeknik Negeri Bali | 2 |
| I Wayan Temaja | Politeknik Negeri Bali | 2 |
| I Nyoman Gede Baliarta | Politeknik Negeri Bali | 2 |
| Nyoman Sugiartha | Politeknik Negeri Bali | 2 |
| N. Putra | Affiliation unknown | 1 |
| Mulya Juarsa | National Nuclear Energy Agency of Indonesia | 1 |
| Irwin Pratama Putra | University of Indonesia | 1 |
| Ranggi Sahmura | University of Indonesia | 1 |
| I Made Gatot Karohika | Udayana University | 1 |
| I Gusti Agung Kade Suriadi | Udayana University | 1 |
| Tjokorda Gde Tirta Nindia | Udayana University | 1 |
| I Ketut Adi Atmika | Udayana University | 1 |
| I Gusti Komang Dwijana | Udayana University | 1 |
| Anak Agung Istri Agung Sri Komaladewi | Udayana University | 1 |
| Gopi Prasetiyo | Udayana University | 1 |
| . Sudirman | Affiliation unknown | 1 |
| I Wayan Suastawa | Politeknik Negeri Bali | 1 |
| I Nengah Darma Susila | Politeknik Negeri Bali | 1 |
| I Gede Artha Negara | Politeknik Negeri Bali | 1 |
| I B G Widiantara | Politeknik Negeri Bali | 1 |
| I Made Suarta | Politeknik Negeri Bali | 1 |
| Sudirman Sudirman | Politeknik Negeri Bali | 1 |
| I Made Sugina | Politeknik Negeri Bali | 1 |
| I Wayan Temaja | Politeknik Negeri Bali | 1 |
| I Made Joni | Padjadjaran University | 1 |
| I Kadek Ervan Hadi Wiryanta | Politeknik Negeri Bali | 1 |
| Tjokorda Gde Tirta Nindhia | Udayana University | 1 |
| I Dewa Made Susila | Politeknik Negeri Bali | 1 |
Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.