Melola Discovery

← Melola Discovery

Open access Journal

Fatigue Life Analysis of Mooring Cleats on The N219A Aircraft Floater Based on Numerical Simulation

Zona Laut Jurnal Inovasi Sains Dan Teknologi Kelautan · Vol. ume (2024) · pp. 213–222

DOI
10.62012/zl.v5i2.42798
ISSN
2721-5717, 2747-2124
Published
2024-07-27
Publisher
Departemen Teknik Kelautan Universitas Hasanuddin
Language
en
License
creativecommons.org/licenses/by/4.0

Abstract

One of the procedures for rescuing a seaplane after an operational is to secure it, namely by mooring at an available port or mooring at a mooring buoy. This mooring buoy is considered a vehicle necessary for securing seaplanes in coastal conditions where it is not yet possible to build infrastructure in the form of an amphiport. To overcome this problem, seaplanes need to add a mooring cleat at the end of the bow of each float, which attaches the rope to the mooring buoy itself. So, it is necessary to study the strength of the mooring cleat itself when withstanding environmental loads. This study was carried out by modelling the mooring cleat using the finite element method to determine where the most significant stresses occur in the mooring cleat structure. Mooring cleats are modelled on deck thickness with varying thicknesses of 20mm and 40mm. The stress that occurred in the mooring cleat structure is then calculated using the Palmgren-Miner rule to determine the fatigue life of the mooring cleat for each variation. It was found that the largest von Misses stress experienced by the structure using 7075-T6 aluminium material was 147.87 MPa, which occurred in the mooring cleat, which was located on the 20mm deck thickness variation at the portside. Meanwhile, this variation's most extended fatigue life calculation occurred for the 40mm deck thickness variation on the portside with 514.43 years.

Keywords

Collaboration network of the authors

25 authors · 102 co-authorship links · 19 across different organisations

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • National Research and Innovation Agency
  • Institut Teknologi Sepuluh Nopember
  • Hasanuddin University
  • Universiti Sains Malaysia
  • UCSI University
  • Affiliation unknown
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
Endah SuwarniAffiliation unknown2
Cakra WijayaAffiliation unknown2
Endah SuwarniAffiliation unknown2
Cakra WijayaAffiliation unknown2
Habibi PalippuiHasanuddin University1
Juswan SadeHasanuddin University1
SilvianitaInstitut Teknologi Sepuluh Nopember1
Faizal SattuInstitut Teknologi Sepuluh Nopember1
Abdul GhofurNational Research and Innovation Agency1
Raj RajendranAffiliation unknown1
Mahmud Iwan SolihinUCSI University1
Affiani MachmudahNational Research and Innovation Agency1
Elmi Abu BakarUniversiti Sains Malaysia1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) https://journal.unhas.ac.id/index.php/zonalaut/oai, first harvested 2 Nov 2026, last seen 15 Nov 2026.
Original metadata (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Fatigue Life Analysis of Mooring Cleats on The N219A Aircraft Floater Based on Numerical Simulation</dc:title>
	<dc:creator xml:lang="en">Yulfani, Rosi Dwi</dc:creator>
	<dc:creator xml:lang="en">Rosyid, Daniel M.</dc:creator>
	<dc:creator xml:lang="en">Nugroho, Wibowo Harso</dc:creator>
	<dc:creator xml:lang="en">Priohutomo, Kusnindar</dc:creator>
	<dc:creator xml:lang="en">Sugiarto, Moh. Muria Armansyah</dc:creator>
	<dc:creator xml:lang="en">Arianti, Erdina</dc:creator>
	<dc:creator xml:lang="id">Yulfani, Rosi Dwi</dc:creator>
	<dc:creator xml:lang="id">Rosyid, Daniel M.</dc:creator>
	<dc:creator xml:lang="id">Nugroho, Wibowo Harso</dc:creator>
	<dc:creator xml:lang="id">Priohutomo, Kusnindar</dc:creator>
	<dc:creator xml:lang="id">Sugiarto, Moh. Muria Armansyah</dc:creator>
	<dc:creator xml:lang="id">Arianti, Erdina</dc:creator>
	<dc:subject xml:lang="en">Mooring Cleats</dc:subject>
	<dc:subject xml:lang="en">N219A</dc:subject>
	<dc:subject xml:lang="en">Stress</dc:subject>
	<dc:subject xml:lang="en">Palmgren-Miner</dc:subject>
	<dc:subject xml:lang="en">Fatigue Life</dc:subject>
	<dc:subject xml:lang="en">Mooring Cleats</dc:subject>
	<dc:subject xml:lang="en">N219A</dc:subject>
	<dc:subject xml:lang="en">Stress</dc:subject>
	<dc:subject xml:lang="en">Palmgren-Miner</dc:subject>
	<dc:subject xml:lang="en">Fatigue Life</dc:subject>
	<dc:description xml:lang="en">One of the procedures for rescuing a seaplane after an operational is to secure it, namely by mooring at an available port or mooring at a mooring buoy. This mooring buoy is considered a vehicle necessary for securing seaplanes in coastal conditions where it is not yet possible to build infrastructure in the form of an amphiport. To overcome this problem, seaplanes need to add a mooring cleat at the end of the bow of each float, which attaches the rope to the mooring buoy itself. So, it is necessary to study the strength of the mooring cleat itself when withstanding environmental loads. This study was carried out by modelling the mooring cleat using the finite element method to determine where the most significant stresses occur in the mooring cleat structure. Mooring cleats are modelled on deck thickness with varying thicknesses of 20mm and 40mm. The stress that occurred in the mooring cleat structure is then calculated using the Palmgren-Miner rule to determine the fatigue life of the mooring cleat for each variation. It was found that the largest von Misses stress experienced by the structure using 7075-T6 aluminium material was 147.87 MPa, which occurred in the mooring cleat, which was located on the 20mm deck thickness variation at the portside. Meanwhile, this variation's most extended fatigue life calculation occurred for the 40mm deck thickness variation on the portside with 514.43 years.</dc:description>
	<dc:publisher xml:lang="en">Departemen Teknik Kelautan Universitas Hasanuddin</dc:publisher>
	<dc:date>2024-07-27</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://journal.unhas.ac.id/index.php/zonalaut/article/view/42798</dc:identifier>
	<dc:identifier>10.62012/zl.v5i2.42798</dc:identifier>
	<dc:source xml:lang="en">Zona Laut Jurnal Inovasi Sains Dan Teknologi Kelautan; Volume 5, Number 2, July 2024 Edition; 213-222</dc:source>
	<dc:source xml:lang="id">Zona Laut : Jurnal Inovasi Sains Dan Teknologi  Kelautan; Volume 5, Number 2, July 2024 Edition; 213-222</dc:source>
	<dc:source>2721-5717</dc:source>
	<dc:source>2747-2124</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://journal.unhas.ac.id/index.php/zonalaut/article/view/42798/12458</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2025 Rosi Dwi Yulfani, Daniel M. Rosyid, Wibowo Harso Nugroho, Kusnindar Priohutomo, Moh. Muria Armansyah Sugiarto, Erdina Arianti</dc:rights>
	<dc:rights xml:lang="en">https://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>