Melola Discovery

← Melola Discovery

Open access Journal

Pengaruh Kadar Air dan Ketebalan Papan Terhadap Laju Pengeringan Kayu Karet (Hevea brasiliensis) dengan Penerapan Fase Pendinginan: The Effect of Water Content and Thickness of Rubber Wood (Hevea brasiliensis) Board on The Drying Rate with the Application of the Cooling Phase

Jurnal Silva Tropika · Vol. 8 No. 2 (2024) · pp. 98–104

DOI
10.22437/jurnalsilvatropika.v8i2.35227
ISSN
2621-4113, 2615-8353
Published
2024-12-26
Publisher
Fakultas Kehutanan Universitas Jambi
Language
en
License
creativecommons.org/licenses/by/4.0

Abstract

ABSTRACT Rubber wood is one of the wood species used as furniture raw material. Before processing it into furniture, it needs to be dried first until the moisture content meets the SNI requirements. In this study, drying data for rubber wood with different initial moisture content at several different thicknesses were taken from a furniture company in Central Java and then analyzed descriptively using Microsoft Excel. In the drying process, the company applies a cooling phase in between the heating phases. The results of the data analysis show that drying wood with a thickness of 30 mm takes longer than that with a thickness of 25 mm. On the other hand, in the same initial moisture content range, rubber wood with a thickness of 30 mm has a drying rate that is smaller than the drying rate for wood with a thickness of 25 mm. In the higher moisture content ranges the wood drying rate is greater than rubber wood with a low initial moisture content. Keywords: cooling phase, drying, moisture content, rubber wood, thickness ABSTRAK Salah satu jenis kayu yang digunakan sebagai bahan baku furnitur adalah kayu karet. Sebelum diolah menjadi furnitur kayu karet perlu dikeringkan terlebih dahulu sampai kadar airnya memenuhi persyaratan SNI tentang kayu untuk furnitur. Penelitian ini data pengeringan kayu karet dengan kadar air awal berbeda pada beberapa jenis ketebalan berbeda diambil dari perusahaan furnitur di Jawa Tengah dan kemudian diolah secara deskriptif menggunakan microsoft excel. Proses pengeringan di perusahaan tersebut menerapkan fase pendinginan di sela-sela fase pemanasan. Hasil pengolahan data menunjukkan bahwa pengeringan kayu ketebalan 30 mm membutuhkan waktu yang lebih lama dibandingkan ketebalan 25 mm. Sebaliknya, pada rentang kadar air awal yang sama kayu karet dengan ketebalan 30 mm memiliki laju pengeringan yang lebih kecil dibandingkan laju pengeringan kayu ketebalan 25 mm. Rentang kadar air yang lebih tinggi laju pengeringan kayu lebih besar dibandingkan kayu karet dengan kadar air awal yang rendah. Kata kunci: fase pendinginan,kadar air, kayu karet, ketebalan, pengeringan

Keywords

Collaboration network of the authors

14 authors · 40 co-authorship links

Hover or tap a name to highlight its co-authors. Double-click to open the author's page.

  • Politeknik Industri Furnitur dan Pengolahan Kayu
  • Affiliation unknown
  • Different organisations
  • Same organisation
  • Affiliation unknown
  • Thicker line = more joint articles · bigger circle = more articles
Show as table
Co-authorOrganisationJoint articles
Wahyu WidiyantoPoliteknik Industri Furnitur dan Pengolahan Kayu3
Nurhanifah NurhanifahPoliteknik Industri Furnitur dan Pengolahan Kayu3
Siska AnggirianiPoliteknik Industri Furnitur dan Pengolahan Kayu3
Soleh MuhamadPoliteknik Industri Furnitur dan Pengolahan Kayu3
Desy MulyosariPoliteknik Industri Furnitur dan Pengolahan Kayu3
Taufik Ramadhan FitriantoPoliteknik Industri Furnitur dan Pengolahan Kayu2
Arip WijayantoAffiliation unknown1
NurmadinaPoliteknik Industri Furnitur dan Pengolahan Kayu1
DarwitonoAffiliation unknown1
Titik Wisnu WardhanaAffiliation unknown1
Nurmadina NurmadinaPoliteknik Industri Furnitur dan Pengolahan Kayu1
Alfani Risman NugrohoPoliteknik Industri Furnitur dan Pengolahan Kayu1
Agung Ari PurwantoPoliteknik Industri Furnitur dan Pengolahan Kayu1

Affiliations come from OpenAlex; journal OAI-PMH metadata carries none. Authors without an OpenAlex ID are matched by name, which can merge or split people.

Metadata source: OAI-PMH (metadata jurnal) https://online-journal.unja.ac.id/index.php/STP/oai, first harvested 6 Nov 2026, last seen 16 Nov 2026.
Original metadata (oai_dc)
<oai_dc:dc xmlns="http://www.openarchives.org/OAI/2.0/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:oai_dc="http://www.openarchives.org/OAI/2.0/oai_dc/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.openarchives.org/OAI/2.0/oai_dc/  http://www.openarchives.org/OAI/2.0/oai_dc.xsd">
	<dc:title xml:lang="en">Pengaruh Kadar Air dan Ketebalan Papan Terhadap Laju Pengeringan Kayu Karet (Hevea brasiliensis) dengan Penerapan Fase Pendinginan  : The Effect of Water Content and Thickness of Rubber Wood (Hevea brasiliensis) Board on The Drying Rate with the Application of the Cooling Phase</dc:title>
	<dc:creator xml:lang="en">Wijayanto, Arip</dc:creator>
	<dc:subject xml:lang="en">cooling phase, drying, moisture content, rubber wood, thickness</dc:subject>
	<dc:description xml:lang="en">ABSTRACT
Rubber wood is one of the wood species used as furniture raw material. Before processing it into furniture, it needs to be dried first until the moisture content meets the SNI requirements. In this study, drying data for rubber wood with different initial moisture content at several different thicknesses were taken from a furniture company in Central Java and then analyzed descriptively using Microsoft Excel. In the drying process, the company applies a cooling phase in between the heating phases. The results of the data analysis show that drying wood with a thickness of 30 mm takes longer than that with a thickness of 25 mm. On the other hand, in the same initial moisture content range, rubber wood with a thickness of 30 mm has a drying rate that is smaller than the drying rate for wood with a thickness of 25 mm. In the higher moisture content ranges the wood drying rate is greater than rubber wood with a low initial moisture content.
 
Keywords: cooling phase, drying, moisture content, rubber wood, thickness
 
ABSTRAK
Salah satu jenis kayu yang digunakan sebagai bahan baku furnitur adalah kayu karet. Sebelum diolah menjadi furnitur kayu karet perlu dikeringkan terlebih dahulu sampai kadar airnya memenuhi persyaratan SNI tentang kayu untuk furnitur. Penelitian ini data pengeringan kayu karet dengan kadar air awal berbeda pada beberapa jenis ketebalan berbeda diambil dari perusahaan furnitur di Jawa Tengah dan kemudian diolah secara deskriptif menggunakan microsoft excel. Proses pengeringan di perusahaan tersebut menerapkan fase pendinginan di sela-sela fase pemanasan. Hasil pengolahan data menunjukkan bahwa pengeringan kayu ketebalan 30 mm membutuhkan waktu yang lebih lama dibandingkan ketebalan 25 mm. Sebaliknya, pada rentang kadar air awal yang sama kayu karet dengan ketebalan 30 mm memiliki laju pengeringan yang lebih kecil dibandingkan laju pengeringan kayu ketebalan 25 mm. Rentang kadar air yang lebih tinggi laju pengeringan kayu lebih besar dibandingkan kayu karet dengan kadar air awal yang rendah.
 
Kata kunci: fase pendinginan,kadar air, kayu karet, ketebalan,  pengeringan</dc:description>
	<dc:publisher xml:lang="en">Fakultas Kehutanan Universitas Jambi</dc:publisher>
	<dc:date>2024-12-26</dc:date>
	<dc:type>info:eu-repo/semantics/article</dc:type>
	<dc:type>info:eu-repo/semantics/publishedVersion</dc:type>
	<dc:type xml:lang="en">Peer-reviewed Article</dc:type>
	<dc:format>application/pdf</dc:format>
	<dc:identifier>https://online-journal.unja.ac.id/STP/article/view/35227</dc:identifier>
	<dc:identifier>10.22437/jurnalsilvatropika.v8i2.35227</dc:identifier>
	<dc:source xml:lang="en">Jurnal Silva Tropika; Vol. 8 No. 2 (2024): Jurnal Silva Tropika; 98-104</dc:source>
	<dc:source>2621-4113</dc:source>
	<dc:source>2615-8353</dc:source>
	<dc:language>en</dc:language>
	<dc:relation>https://online-journal.unja.ac.id/STP/article/view/35227/19637</dc:relation>
	<dc:rights xml:lang="en">Copyright (c) 2024 Arip Wijayanto</dc:rights>
	<dc:rights xml:lang="en">https://creativecommons.org/licenses/by/4.0</dc:rights>
</oai_dc:dc>